Question about 2001 Nissan Altima

1 Answer

Key Fob for a 2001 Nissan Altima keeps opening the truck repeatedly when it is in range of the car, but will not unlock or lock the doors.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 770 Answers

You probably have a stuck button. If you can take apart and clean, It'll probably start workin properly. If you can't you may want to try one of those compressed air cleaners, available at best buy or office stores, used to clean keyboards and electronics. If none of that works, you may have to replace the fob...about $60.

Posted on Oct 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I tried to program a new fob for a 1999 Altima. And nothing worked





1.   Close and lock all doors with the driver’s side power lock/unlock switch.

2.   Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast, system will not enter programming mode.

3.   Insert key into the ignition cylinder and turn to the ACC position.

4.   Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful.

5.   If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should flash. Repeat this step for each transmitter (including any existing transmitters).

6.   Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.




Make sure you have the right fob for your car.

Nov 15, 2016 | 1999 Nissan Altima

1 Answer

2001 nissan sentra key fob problems


If the battery is definitely good, it is possible that the contacts on your fob for the open door command are dirty or wearing out..

Those fobs are inordinately expensive for what they are so it behooves you to check it out first.

Sep 05, 2015 | 2001 Nissan Sentra

1 Answer

2008 Altima with push button start. Why won't the fob unlock doors?


Insert key into and remove it from ignition more than six times in 10 seconds. When the hazards lights will flash twice insert key into ignition and turn to ACC position.
Then push any button on key fob once, the hazard lights will flash twice. Then open drivers door to END.
Should be all working again.

Jun 06, 2015 | 2008 Nissan Altima

1 Answer

I changed my car battery, now my 2008 Nissan Altima key fob won't work


There is a special procedure involved in keying your fob to your car once the battery has been changed. You must lock and open the door with your key. Turn the ignition to "on"(not start) then push the fob's open and close button, then shut off ignition. This procedure is done everything the key battery is changed. Hope this can help you!
------------
Motorcycle Diagnostic Scanner

Oct 31, 2012 | Cars & Trucks

2 Answers

I activated alarm and car will not start,. How to deactivate alarm and start car? I have a 98 Nissan Altima


ON NISSAN MANUALLY LOCK ALL DOORS THEN UNLOCK THE PASSENGER DOOR WITH THE KEY THEN THE DRIVER DOOR THEN PRESS AND HOLD THE BRAKE PUT KEY IN IGNITION THE CAR SHOULD START NOW THIS RESETS THE ALARM

Aug 02, 2011 | 1998 Nissan Altima

1 Answer

Sorry my car was not listed so picked Altima 2003 Micra Intelligent key fob not working properly. Can drive the car but cannot open or lock the doors. Did get fob wet. Now dried out. Worked for first few...


You are going to need to check the power lock control moduel on the inside of the door panel. If the FOB appears to be working but the doors are not unlocking, you need to check this. I would also replace all fuses that control the locks. If both of these devices check out ok, you may need to replace your FOB. To check your power lock control moduel, manually lock and unlock your doors by pressing the lock button on the inside of the door. If it does not work, it is either the fuses or the power lock control moduel. If it works, your FOB has gone bad. Hope this helps! Please rate 4 thumbs up!

Apr 18, 2011 | Nissan Altima Cars & Trucks

1 Answer

The key fob will lock all the doors, but wont unlock them


Time for a new remote lol. I would open the remote out and clean it really good and see of that helps. If not like I said time for a new remote.

Dec 31, 2010 | 2001 Nissan Altima

1 Answer

Hi I want to program a new keyless fob. I have the original fob that works great.Do I need to do anything to the original key when I program the new fob? 2006 nissan altima


1. Close and lock all doors with the driver’s side power lock/unlock switch.

2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.

3. Insert key into the ignition cylinder and turn to the ACC position.

4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.


5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).

6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.

Nov 16, 2009 | 2006 Nissan Altima

Not finding what you are looking for?
2001 Nissan Altima Logo

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...