Question about 2002 Buick LeSabre

1 Answer

How do I remove the glove box? I have removed 2 screws along the inside top and one screw on the right side that also had wire to support door. But the glove box still will not come out. It won't even budge.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

After removing the three screws, the glove box is held with two clips - one on each side. The clips will come undone when you pull on the glove box with a little force. You will then need to unplug the switch/lamp connector.

Posted on Nov 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove centre glove box on 2004 Renault scenic


Lift up gearstick gaitor leaving plastic surrounding in place.

Lift plastic surround and remove lock and Hazzard switch.
Push gaitor through surround and remove surround.
Remove ***** from front of centre consoleand 2 screws from rear.
Follow the side of the centre console down into footwell and remove Popper from each side.
Pull console forward slightly and disconnect cigar lighter.
Remove centre console.
Remove 2 screws below the radio.
Pull radio/air-conditioning surround forward, leave the radio in the surround as it will come out with the surround.
Remove 2 screws holding the glovebox to the centre console.
Open glovebox.
Remove 3 screws along the top front.
Open the fuse box at back of glove box and push the fuse holder up off the flap.
Open passenger door.
Remove dash side panel and remove 2 screws.
Remove kick panel trim in passenger footwell and remove ***** from bottom of glove box. (The glovebox will need to be open to see this *****)
Pull glovebox out slightly. It can be hard to pull out, just be sure you have all screws out.
Disconnect glovebox light and light switch.
Remove glovebox fully.

Apr 03, 2016 | Renault Cars & Trucks

8 Answers

1995 Jeep Grand Cherokee Laredo Alarm system


Hi,

Please CLICK HERE this link will help you out..

Goodluck..

May 14, 2008 | 1995 Jeep Grand Cherokee

1 Answer

How to change cabin filter 2011 Lacrosse


I just changed mine yesterday and these tips listed above were unfortunately incorrect.

Step 1 - Open the passenger door
There is a panel that has no screws on the flatside of the dashboard which faces against the closed door at the jam side. Use a body tool and pry the panel carefully exposing the inside area of the glovebox. If possible dont do this in cold weather because the tabs are plastic. Inside the panel you will see one small tab that the glove box has a 1/4 plastic clip seated in the tab.

Step 2 - Open the glove box. Remove the 3 hex screws on the top interior row of the glove box.

Step 3 - At the right and left corners of the bottom of the glove box remove the two front facing screws on the lower hinge.

Step 4- At the very bottom parallel to the floor there are two more hex screws remove those (they hold the plastic vent in place underneath the glove box. Pull the vent downward to release the tabs.
IMPORTANT: Dont forget to go back to step 1 and pull the small tab from the slot in the dashboard cover area ( Inside the panel you will see one small tab that the glove box has a 1/4 plastic clip seated in the tab)

Step 5 - Pull down on the glove box to release the clips.

Step 6 - You will see a black box inside. There are three tabs (right, top, and left) pull them individually to remove the front facing cover. Inside you will see the air filter. Remove and have airflow arrow pointed downward.

Reverse steps to reinstall. Be sure to line up the clips before pressing them back in place. Do not force them!

Good luck. I hope this helps. I did mine on the first attempt with no issues in about 10 minutes (I'm not a mechanic).

Aug 26, 2012 | Buick LaCrosse Cars & Trucks

1 Answer

The catch on the glove box lid on a vw golf 2001 is broken how do i fix it?


You need to replace the whole glove box door. Pry the panel on the right side of the dash off, remove the t25 screw, remove the 3 t20 screws along the bottom of the glove box, and the t20 screws that you can see inside the glove box. This will loosen it enough to pull the whole glove box loose. Then you need to remove the damper by prying the little plastic pin out. Then remove the bracket it secures to that has a t20 screw in it. There are 2 plastic pins in the hinges that need to be popped out, once this is done, the door will come off. Reassembly is the reverse.
If the pins are difficult to reinstall, file the new glove box door hinge holes with a round file. I usually shoot a little oil into the damper too, just to make operation easier.

Feb 04, 2011 | 2001 Volkswagen Golf

2 Answers

How to change cabin air filter in 2005 pontiac vibe


it's located behind the glove box. Instructions are in you owners manual. basically you remove the glove box and remove a plastic cover to access the filter. make sure you install the filter right side up. under $10 at rockauto.com

Aug 08, 2010 | 2005 Pontiac Vibe

2 Answers

The blower does not work on the first 3 speeds only works on high


This is a pretty common problem. It's the blower motor resistor. It's a cheap & easy fix with normal tools. The resistor is located on the top of the blower motor housing which is on the passenger side of the truck under the dash (just below the glove box). In order to change it, you need to remove the glove box liner. There are just normal screws holding the glove box in (Either Phillips or Torx head screws). Take the screws out, pull out the glove box, and the resistor cover will be visable. There is a wiring pigtail/connector plugged into it. All you will see is the wires going into a flat square black plastic piece that is screwed onto the top of the housing. Unplug the wire connector, remove the 3 screws or nuts (I've seen both used) holding the resistor cover on, and then wiggle the cover up and out. The resistor is mounted to the backside of that black plastic square you are pulling up and out. The resistor is a cheap part. Locally (Minnesota) it's $15.99 for your 2000 Blazer at O'Reilly. On a few I have done, I didn't have to remove the glove box door, (or the junk in the glove box), just the liner with the junk still in it. On a few Fords I had to remove the door too. I have replaced resistors in about 20 minutes start to finish. Good luck and I hope this helps. Here is a picture of your resistor as a visual aid for when you remove the glove box liner. You'll see the top of this and as you can see in the picture, the spot where the wire connector plugs in to the center of it along with the 3 screw/bolt holes. One on each corner of the top side in the pic, one in the middle of the bottom side. You can also see the resistor itself on the back side of the cover in this picture.
91b9946.jpg

Jan 14, 2010 | 2000 Chevrolet Blazer

1 Answer

How to change cabin air filter in toyota avalon 2002?


1) Turn off the ignition switch while leaving the wipers in the up position. 2) Open the hood and properly secure it in the open position. 3) Gently pull the rubber cowl seal away from the cowl vent screen. Place your hand underneath the right half of the cowl vent screen and lift straight up, thereby releasing the four spring clips and removing the right half of the screen 4) Remove the water shield. Carefully disengage the two water shield locking tabs and slide the water shield toward the front of the vehicle, lifting the water shield up and away from the vehicle 5) Remove the Passenger Compartment Air Filter, being careful not to allow debris or loose components to fall into the filter housing. Replace the Passenger Compartment Air Filter with a fresh filter and reverse the above procedures to reassemble the vehicle components. �
I am not sure what time in the year your 2001 Avalon was built but her is the procedure that I just followed: 1. Open glove box and remove contents 2. Remove the three philips head screws along the top inside frame of the glove box. 3. Remove the hex head bolt in the lower right and Philips screw in the lower left side of the glove box frame. 4. Unlatch the black cover plate from the roof of the glove box. This holds an electrical connection and will need pushed up through the hole when the entire box is removed. 5. Pull on the top left side of the glove box to release the pop tab. Repeat on the right side. 6. Carefully lower the glove box assembly. 7. Disconnect the electrical connection to the trunk disable button 8. The entire glove box can now be removed from the area. The door gear assembly does not come off of the box and is easily damaged if attempted to do so. 9. The Cabin Air Filter assembly has a white cover. Pop the tabs on the right and left side and slide the assembly out. 10. Replace the filter in the assembly. Make sure the airflow indicator points down. 11. Re-Install Air Filter assembly. 12. Re-Install the electrical connections remembering to slide the one through the hole in the top of the glove box. 13. Push glove box assembly on pop tabs. 14. Re-Install screws and bolts. 15. Reconnect the black cover plate to the top of the glove box.
rate it

Jan 08, 2010 | 2002 Toyota Avalon

2 Answers

How to change front blower motor in a 2003 dodge caravan


Removal & Installation
CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.

  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel
d6b70fa.gif
The blower motor is located behind the glovebox, behind the blower motor cover

  1. Remove the A/C-heater blower motor cover.
  2. Disconnect the blower motor wiring connector.
  3. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  4. Remove the blower motor mounting screws.
0e0729c.gif
Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

1ed158c.gif
The blower motor is secured to the housing with three small screws

  1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.

Oct 12, 2009 | 2003 Dodge Caravan

1 Answer

Where is the cabin air filter located on an 07 Hyundai Tiburon?


The cabin filter is located behind the glove box.

Remove the three screws along the bottom edge of the glove box door.

Open the glove box door and remove the three screws along the top edge just inside where the door closes.

Pull the glove box assembly out and you will see the cabin filter cover behind it. It is a (approx.) 1.5"x10" plastic plate that snaps out.

Remove the cabin filter cover and slide the old filter out, noting the orientation. Install the new filter in the same orientation then reassemble the vehicle.

Sep 20, 2009 | 2007 Hyundai Tiburon

1 Answer

How do I change the cabin filters on a 2004 Hyundai XG350L


you will need a phillips screw driver and pliers. now first open the glove box and remove the clamps on etch side on the inside that stops the glove box from falling out then remove the screws from the inside top edge bottom right then remove the bolts at the bottom remove the glove box then look for a vertical door lift from the bottom and remove this peace then take out your air filter. I KNOW THIS IS A LOT SO IF YOU NEED ME TO POST A YOUTUBE VID JUST LET ME KNOW

Apr 05, 2009 | 2004 Hyundai XG350

Not finding what you are looking for?
2002 Buick LeSabre Logo

Related Topics:

1,389 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...