Question about 2005 GMC Canyon

1 Answer

The fan will work only at position 4 (maximum), is it the control ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Its the resistor. its located down to the left of the blower motor, 4 wires.

Posted on Oct 01, 2009

Testimonial: "Quick response. Thanks "

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hi I recently purchased an 05 Chevy Equinox. I'm positive it needs a tune up. What would be the BEST brand of oil to use for this Vehicle? & is it normal that while it is on & not moving, the temp gauge...


The original oil used is 5W-30. I would use fully synthetic for maximum protection.
Yes the engine should reach just above normal before the fans switch on.

Sep 07, 2017 | Cars & Trucks

1 Answer

How do I reset the remote key


Try this it worked for my s60 and recently on my C30
S/V 90
Procedure
1. Sit in the vehicle with all doors closed.
2. Turn the ignition key on and off five times (not to start position, but the on position) and on the fifth time leave in the on position.
3. Press the remote lock/unlock button several times (if there is a dashboard mounted LED it should light for 2 seconds and then it should flash for 10 seconds) to synchronise the remote to the control unit. Repeat this for additional remotes.
4. Switch off the ignition and test the remotes. A maximum of 4 remotes can be programmed.
S/V90 (Alternative Method)
Procedure
1. Close all the doors, the bonnet and the boot.
2. Switch the ignition on and off 5 times within 10 seconds, and leave the ignition on the fifth time.
3. Press one of the two buttons on each remote control.
Note: The first remote control has to be programmed within 15 seconds. The rest must be programmed a maximum of 10 seconds apart from each other.
4. Switch off the ignition and test the remote controls.
If you are unsure how to program your remote controls, please contact your Volvo dealer.

Nov 06, 2013 | 2004 Volvo XC90

2 Answers

VW Golf 2000 A/C and Fan Blower problem


In most cases, the problem related to blower and A/C switch lies with the fan controller relay which is fitted on the housing of the blower. It is a small circuit board and your fan is connected through this circuit relay and it controls the speed of the fan which further due to safety circuit controls the A/C. indirectly. Check that.

Apr 14, 2012 | 2000 Volkswagen Golf

1 Answer

The fan will not come on in the first 4 positions,


It may be the fan motor reostat. It's located under the dash on the passenger side on the duct work. It kinda works like a dimmer switch.

May 27, 2010 | 2001 Chevrolet Impala

1 Answer

The central locking on my ford focus has stopped working, i have changed the battery in the key fob but no luck, can you help. graham.


Obtain all keys fitted with remote control. Fasten seat belts and close all doors. Turn ignition switch from position I to position II 4 times within 6 seconds. Switch ignition OFF. Programming mode activated for 10 seconds proceed as follows: Press and hold lock, unlock or boot release button Fig. 1 [1], [2] or [3]. Wait for acoustic signal (indicates correct programming). Repeat above procedure within 10 seconds to program remaining keys. To exit programming mode: Turn ignition switch to position III or wait 10 seconds. Keys can also be programmed using diagnostic equipment.
NOTE: A maximum of 4 keys can be programmed.

Jan 06, 2010 | 2001 Ford Focus

1 Answer

Problems with the air conditioner fan of Cutlasss Supreme SL '94


Sounds like you have either a bad fan connection or you need to replace the fan motor itself.

Check all the wiring leading to the fan, and the fan controller.

Nov 13, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Front heater/ac blower in 2004 Grand Caravan does not work at all


the heat or cold adjustment control in my 2002 grand caravan will only work on maximum adjustment, if you try to reduce the speed of the blower by turning the control knob 1 knot, 2, 3 and 4 down it won't work it only work at the last position which is the 5th or last turn of the control knob. please let me know what could be the problem. thanks.

Oct 03, 2009 | 2002 Dodge Grand Caravan

1 Answer

Chrysler Vision (Eagle Vision) A/C ventilator works all the time at max.


The problem was in ventilator valve resistor, located below glow box, near ventilator. A transistor replacement did the job!

Sep 01, 2008 | 1996 Eagle Vision

Not finding what you are looking for?
2005 GMC Canyon Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...