Question about 2005 Isuzu Ascender

1 Answer

Which fuze do i replace on a 2005 isuzu ascender if my trailer recepticle is not working? i have already replaced all the trailer lights and electronics, it's not the trailer.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 247 Answers

I assume that you have a trailer light attachment installed at the rear of the vehicle somewhere around the tow hitch,turn on your head lights,obtain a volt meter and check D.C. voltage on the pigtail,ground the black lead to clean frame metal and check the pins on the plug with the red lead,one of them should be live 12v dc.that will be your trailer running lights,theother will be brake lights,you will have to have someone hold trheir foot on the brake to test it,dont assume the trailer is ok. verify voltage at the connector on the vehicle first,if you have 12 v,there the trailer has the problem,or if it hasnt been used in a long time the connector may need to be cleaned,as far as the fuse goes depending how it was installed,could be several choices,set your meter on continuity and check all fuses,you dont have to phisically remove each one,if you look close there are two small contact points on both sides of the amp rating number,most likely you will have two or three fuse panel locations,primary is under dash drivers side ,secondary panels and relays located in engine compartment under hood on fender walls black plastic box w/cover,,also may be on the sides of the dash board,can only see when the door is open ,or behind the ashtray in the center console,replace any fuses that are blown,be aware of the plug configuration on the car to the trailer,and that the ground wire on the car side of the plug is also the ground lead on the trailer connector, wires may have got mixed up during repair,happens to the best of us once in a while,clean ground connections are very important on trailers,old rusty wires and scerws should be removed wire brushed and reinstalled,or replaced if needed,then sealed with varnaloc,or spray paint,to protect them,hope this helps you.aloha from maui todd0708

Posted on Oct 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is electronic control unit 10 p0256 means on 2005 Isuzu ascender?


code p0256 refers to injector 2---circuit high===causes wiring short to positive ---injector---ECM
check wiring is good at connections
replace faulty injector

Sep 29, 2014 | 2005 Isuzu Ascender

1 Answer

How replace smog pump in 2005 Isuzu Ascender


How do you know the pump is defective, what is the code?

Aug 31, 2014 | 2005 Isuzu Ascender

1 Answer

Ascender radio fuse location


radio fuse is located under driver side dashboard mounted on firewall or in-line behind the radio mount.

Jun 08, 2014 | 2005 Isuzu Ascender

1 Answer

2005 S Isuzu Ascender Speedometer niddle moved all the way to the right of gage and as not moved.


If the odometer is working correctly, the problem is inside the speedometer head.
The speed sensor would be on the side of the transmission if the odometer is not working.

Apr 07, 2013 | 2005 Isuzu Ascender S

1 Answer

I had a P0410 code. I repladed the air pump on my 05 Isuzu Ascender and the check engine light came back on the next day after replacement.


this is an obd2 trouble code table, it canhelp you understand the meaning of code.
for this code youc can try:

Replace the AIR pump AND one-way check valve

Test and clean the AIR pump AND test and replace the one-way air check valve

Replace the AIR pump inlet hose

Replace the AIR pump fuse (found under the hood)

Jul 29, 2011 | 2005 Isuzu Ascender

1 Answer

How to replace the oil cooler on my 2005 isuzu


Why would any car have a power steering cooler?
It could never get very hot, and it would not matter if it did.

May 05, 2010 | 2005 Isuzu Ascender

1 Answer

I have a 2005 Isuzu ascender, the gauge light keeps coming on. The oil gauge drops to zero. I have gotten an oil change and new filter. What can the problem be now?


It could be a bad oil sending sensor, or the oil pump. When it drops, does the gauge stay on zero or fluctuates. The sending sensor isn't to bad to replace or cost wise, but pump is a different story. Have someone check the sending unit or just have it replaced to see if that's the problem.

Jan 17, 2010 | 2005 Isuzu Ascender

1 Answer

Check engine light on 2005 isuzu ascender, code PO128 is given...help!!


that code means that the coolant is cooler than it is supposed to be and it cannot be regulated...which means the thermostat is stuck open or broken,so replace the thermostat and that should solve your problem,hope this sheds a little light on it!

Sep 26, 2009 | 2005 Isuzu Ascender

1 Answer

How to replace climate control light


Have You checked the fuses first?

Jan 21, 2009 | 2005 Isuzu Ascender

Not finding what you are looking for?
2005 Isuzu Ascender Logo

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...