Question about 2005 Nissan Altima

1 Answer

Where is the crank shaft sensor located on the 2005 altima 2.5s automatic

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 144 Answers

The crankshaft position sensor is on the right rear of cylinder block, below starter motor.

Posted on Oct 01, 2009

Testimonial: "great just what i asked realy helpful thanks"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Nissan Altima crank shaft censor located bank 2


there is only one crankshaft sensor so you will be looking for a CAM shaft sensor for it to be on bank 2
go google and type in --location of cam shaft sensors on nissan altima engine ---

Dec 18, 2016 | Nissan Cars & Trucks

Tip

Tips for your 2005 Nissan Altima 2.5 crank shaft sensor


If your 2005 Nissan Altima is sputtering or seems to stall in mid drive at speeds of 55-70 mph or just shuts down at low speeds or idle this may be due to your crank shaft sensor.
The crank shaft sensors were originally made of plastic and were later "upgraded" to a metal sensor.
To change you will need a 10 mm Hex socket wrench, a long flat head screw driver, and if you have access I would recommend a lift.
To access the sensor you will be under the vehicle and you will see a guard plate over the exhaust, remove this so you can have some arm room to reach up behind the engine. reaching up with your right arm you should begin "blindly" feeling for the sensor which by looking at the new one you can be able to tell what it feels like. There will be the connector you need to detatch be careful not to break it. Once you locate it use the wrench to remove the bolts and the flat head to help wedge it out. Once the sensor is out you
Once you remove the old sensor the new one will be a tight fit but it does fit, be sure to attach the sensor cords before putting the new sensor back in. but once you have it attached take a little oil and lubricate the sensor to help it slide back in, reattach the bolts and now your done.

on Aug 09, 2010 | Nissan Altima Cars & Trucks

1 Answer

Location of crank shaft position sensor on 2006 nissan altima


its on the back side of the engine near the bell housing there was a factory recall on some of those

Sep 22, 2012 | 2005 Nissan Altima

1 Answer

Whant to know where crank shaft possition sensor is located


should be next to and behind crankshaft pulley 

Sep 26, 2009 | 2005 Nissan Altima

2 Answers

CRANK SHAFT POSITION SENSOR 20002 NISSAN ALTIMA


1st, Nissan had a recall on Crank position sensors for 2002-2006 Altima's. Check with you dealer before you go doing any repairs. You may discover you can get your car repaired at no charge.
NHTSA Campaign ID number :O7V527000
Symptom: Erratic behavior. Stalling and no starts and very difficult to diagnose due to the time frame in which the component actually malfunctions. The warranty should not be limited to the original owner.
I would also need more specifics as to which engine you have so I might assist you in where the location of the sensor is. The Altima had a 4 and a 6 cyl engine offered that year.

Dec 18, 2008 | 2005 Nissan Altima

2 Answers

2005 Subaru Baja Crank Shaft Position Sensor


is there a problem using e10 ethonal in a subaru impreza wrx 2003

Nov 10, 2008 | 2005 Subaru Baja

1 Answer

Crank shaft sensor


I believe if memory serves me right its on gear box housing , in slightly different areas depending on gearbox

Oct 23, 2008 | 2003 Nissan Altima

3 Answers

Crankshaft poistion sensor location for 2005 nissan altima


Its right next to the passenger side drive shaft, where it goes into the transmission. Right above the drive shaft. It s black with green slider inside of the connector and it has 3 wires coming out of it.

Jul 23, 2008 | 2005 Nissan Altima

Not finding what you are looking for?
2005 Nissan Altima Logo

423 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...