Question about 2004 Ford Freestar

Open Question

Can a hydronic 4 coolant heater be installed on a 04 ford freestar

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

04 ford explorer heater blows cold coolant does not circulate


Number 12 is heater control valve. Number 11 is vacuum line, full vacuum and the valve will shut off coolant flow. I can't say the valve is the problem? Maybe the heater core needs to be flushed? When you say coolant doesn't flow, you mean through heater core?
26386563-zoyd2ay4ajnqri3x4p5ocmly-3-0.jpg

Dec 05, 2016 | 2004 Ford Explorer

1 Answer

Need the code PO722 for a 2006 ford freestar 3.9


Hope, code PO722 Output Speed Sensor No Signal.
Possible trigger for code,
  • Defective Output Speed Sensor
  • Defective Shift Solenoids
  • Defective Engine Coolant Temperature Sensor
  • Defective Valve Body
  • Dirty transmission fluid that restricts the hydraulic passages
  • Defective Output Speed Sensor wiring or connector
P0722 Ford Output Speed Sensor No Signal
http://www.autozone.com/repairguides/Ford-Freestar-Monterey-2004-2006/Diagnostic-Trouble-Codes/4-2L-V6-VIN-2-Auto-5/_/P-0996b43f802e829c

Aug 27, 2016 | 2006 Ford Freestar

1 Answer

How do you by pass the security system on a 04 ford freestar


Ropes, google search (bypass the security system on a 04 ford freestar) and you will see a few videos, etc to show how.

Press the helpful button

Feb 10, 2016 | Ford Cars & Trucks

1 Answer

04 Ford freestar I got on the eway once I hit 55mph my c to h gauge went to the car didn't smoke or overheat. I got off the eway it went back down. the engine symbol cut on it will not cut oFf. why?


Check the coolant level! You may be so low that it isn't able to circulate between the engine block and radiator. Add water / coolant mixture to the radiator when the engine is *cold* and then start the engine. Continue topping off the radiator as the engine reaches normal operating temperature. Finally, add water / coolant to the warm / hot level indicator on the coolant reservoir.

Apr 24, 2015 | 2004 Ford Freestar

1 Answer

How do I change a waterpump on 2005 ford freestar van


Remove the fan while coolant is draining into a bucket. Remove the belt. Once that's all out of the way you can get to the water pump. Remove the lower radiator hose from the pump and the water line to the heater core from the pump. Now remove the securement bolts and remove the water pump.

Sep 25, 2014 | 2005 Ford Freestar

1 Answer

Right passenger slide door does not lock with remote on 04 ford freestar


If someone else tries to open the door when you push the button it can mess it up.. i remember when i messed up my mom's car and she has the same car :) we went to ford and they fixed it somehow!

Jul 11, 2012 | Ford Freestar Cars & Trucks

1 Answer

Who knows where I can get a guide to replace the Heater Core on my 2006 Ford Freestar?


I have the shop manual & wiring book from Ford for your car. If interested, let me know. $25 plus postage.

this is a big job, time consuming. Is it leaking coolant?

Removal and Installation
NOTE: If a heater core leak is suspected, the heater core must be leak tested before it is removed from the vehicle.
  1. Drain the cooling system. For additional information, refer to Section 303-03.
  1. Position the front seats fully rearward.
  1. Depower the supplemental restraint system. For additional information, refer to Section 501-20B.
  1. Remove the wiper motor and pivot assembly. For additional information, refer to Section 501-16.
  1. Remove the LH and RH windshield side garnish mouldings. For additional information, refer to Section 501-05.
  1. Remove the LH and RH A-pillar lower trim panels. For additional information, refer to Section 501-05.
  1. Disconnect the heater hoses from the heater core.
  1. Lower the glove compartment.
  1. Remove the 3 steering column opening panel lower bolts.
    • To install, tighten to 8 Nm (71 lb-in).
  1. Remove the steering column opening panel cover.
  1. Remove the steering column opening panel upper bolts.
    • To install, tighten to 8 Nm (71 lb-in).
  1. Remove the steering column opening panel reinforcement.
  1. Remove the 4 storage console pin-type retainers.
  1. Remove the storage console.
  1. Remove the rear seat floor duct adapter.
  1. Remove the upper instrument panel finish panel.
  1. Remove the LH lower instrument panel bolt.
    • To install, tighten to 12 Nm (9 lb-ft).
  1. Remove the LH upper instrument panel bolt.
    • To install, tighten to 12 Nm (9 lb-ft).
  1. Remove the 4 upper instrument panel bolts.
  1. Remove the upper instrument panel cowl bolt.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the 4 instrument panel center support brace bolts.
    • To install, tighten to 12 Nm (9 lb-ft).
  1. Remove the LH instrument panel support bracket bolt.
    • To install, tighten to 12 Nm (9 lb-ft).
  1. Loosen the RH instrument panel bolts one half of the bolt length, but do not completely remove the bolts.
    • To install, tighten to 12 Nm (9 lb-ft).
  1. Working through the glove compartment opening, remove the RH instrument panel support bracket bolt.
    a0083958.jpg
  1. Position the LH side of the instrument panel slightly away from the dash panel.
  1. Remove the heater core and evaporator core housing support brace nut.
  1. Remove the heater core and evaporator core housing support brace bolt.
  1. Remove the heater core and evaporator core housing support brace.
  1. Remove the 4 floor duct screws.
  1. Remove the floor duct.
  1. Remove the 7 heater core cover screws.
  1. Detach the wire harness from the heater core cover.
  1. Remove the heater core cover.
  1. Remove the heater core.
  1. To install, reverse the removal procedure.
  1. Fill the engine cooling system. For additional information, refer to Section 303-03.

Oct 31, 2011 | 2006 Ford Freestar

1 Answer

How to know if heater core leaking on freestar 2004


If you have an odor of coolant inside the vehicle, or the windshield fogs up when the defroster in turned on, or the carpet on the passenger floor is wet and doesn't dry, you probably have a heater core leaking.

Sep 22, 2011 | 2004 Ford Freestar

1 Answer

How do i change the coolant/flush radiator in 2004 ford freestar


Open the petcock on the bottom of the radiator and allow the old coolant to drain.

Close the petcock.

To refill you will first fill the degas container to the cold fill range, leave the cap off the canister. Turn all of the heater controls to warm and turn fan to full. Idle the engine until the thermostat opens. Top off the coolant and put the cap back on. Idle at 3000 RPM for several seconds and then idle again for a minute or so. Check the level and then repeat this 4 times, or until heat is coming from the front and rear heat units.

If you want to flush the system you will have to remove the thermostat and hook up your flush system to the radiator hose at the thermostat housing. Follow the instructions on your flush system then put the thermostat back in. Follow the instructions above to refill.

Dec 12, 2009 | 2004 Ford Freestar

Not finding what you are looking for?
2004 Ford Freestar Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...