Question about Chrysler Town & Country

1 Answer

1996 town and country 3.3 ltr engine 1.) service light came on, turned key back on and off three times and counted the service light...three blinks, a pause, and two more.. code 32 on the dash.i I assume. 2.) I did notice sometimes when I turn on the van the rpm and speedo are not working. and need to turn off and then on again a minute later to work 3.) also tranny is not always kicking down as it should to a another gear...its like Im in 3rd not in drive at 45 mph....it should be at aoput 1600 rpm but its up at 2000 until I speed up a little...so do I need more tranny fluid? 4.) and I do know that the wipers are not...nieither the front nor the rear...is there a Relay behind the center consule where the radio is? I heard a clicking there before inop wipers,.

Posted by on

1 Answer

Have you checked the trans fluid or ever changed it?

Posted on Oct 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the camshaft sensor located on 1996 Chrysler town and country lxi


Well the sensor should be on the drivers side just under the valve cover and it looks like a circle with a plug in it.I think your problem though is the timing belt is off a tooth it will run fine but being a tooth off will keep that light on.

Jul 09, 2014 | 1996 Chrysler Town & Country

Tip

How To Replace Install Front Wheel Bearing Hub 1996-2007 Chrysler Town And...


How To Replace Install Front Wheel Bearing Hub 1996-2007 Chrysler Town And Country

on Apr 10, 2012 | 2001 Chrysler Town & Country

1 Answer

2005 town and country touring i want to disconnect the seatbelt warning light and chime?


1. Turn the ignition switch to the off position and buckle the seat belt
2. Turn the ignition switch to run (engine does not need to be running), wait for the seat belt light to turn off.
3. Within 60 seconds, unbuckle and rebuckle the drivers seat belt at least 3 times, ending with the seat belt buckled.
4. Turn the ignition key to the off position. A single chime will sound to signify that you have successfully completed the programming.

It can be reactivated by repeating these steps.

The alert will be deactivated but the warning light will continue to stay on will the belt is unfastened.

Feb 13, 2013 | 2005 Chrysler Town & Country

1 Answer

My nissan serena air bag light flashes on and of


"If you have the airbag light, it will show steady for a few seconds (the manual says 7 secs) after you turn the key from off to on (but not start) and then start to flash. Here is how to reset it:

1. Turn the key from off to on.

2. Watch the airbag light closely. It will stay on for a few secs. and then as soon as it blinks off (the start of the flashing), turn the key off instantly.

3. Count to 5 (1 Mississippi, 2 Mississippi . . . .)

4. Repeat steps 1-3 two more times until you have done the cycle three times.

5. Now turn the key on and watch the light. It will start blinking in a different, slower manner. This is diagnostic mode. You can watch this for a little while, no hurry.

6. Now turn the key off again, Count to 5 like in step 3 again, and turn back on. If the procedure worked, the airbag light will not be flashing.

If it does not work the first time, just repeat the steps again."

Aug 06, 2010 | 1996 Nissan 200SX

1 Answer

When I drive my 1996 town and country chrysler van and I push the gas down the car loses power. It makes a loud banging sound. Sometimes it will start to go a little and **** really hard and then you can...


Has the service engine soon light come on ?

This could be caused by a lot of different things, don't replace parts until you know for sure what the problem is otherwise you will just be throwing your money away,

If the service engine soon light IS on then go to auto zone and have them get the codes, on your year you may have to have them turn the ignition key on and off five times, then count the number of flashes of the service engine soon light and then look up the codes in a haynes repair manual for your specific vehicle.

Mar 29, 2010 | 1996 Chrysler Town & Country

1 Answer

How do you read the flashing check engine light codes on a 93 chrysler town & country?


Turn key on and off twice without starting engine. count flashes, their will be slight hesitation, make one digit after hesitation make second digit.(flashes 5 times hesitates flashes three times hesitates your code is 53) if it countiues to flash, its making second two digit code.

Jan 27, 2010 | 2005 Chrysler Town & Country

1 Answer

1996 Chrysler T&C speedometer and tack not alwasy working


Is the check engine light on?
On or not, you can check to see what the error code is by turning the ignition on-off-on-off-on (do not start) and count the number of times the check engine light comes on. This website/pdf will give you good insight to what can be done with various codes regarding transmissions, which may be your problem. Check your code number and see if it is applicable to the list provided.

Without know much more, I would suggest you replace both input and output speed sensors on your transmission. They cost $17-18 each and at this point should be replaced anyway, especially given the lower cost. These can be done while standing in front of the vehicle. Remove the air cleaner and use a 1" socket to unscrew the old and replace with new. (remove wiring before using tools)

Jul 24, 2009 | 1998 Chrysler Town & Country

2 Answers

Air bag light is blinking


my airbag light is blinking . can i reset anything its a04 nissaun armada

May 02, 2009 | 2004 Nissan Armada

1 Answer

2005 Chrysler town & country touring won't turn over.


Sounds like you need a starter, or you have a loose wire somewhere under the hood.

Apr 25, 2009 | 2005 Chrysler Town & Country

1 Answer

Engine light fr ash 10 time


what your check engine light is doing is called the key dance.

The "Key Dance" is a coined term to identify a process of reading MIL fault codes stored by your cars engine computer (PCM). You cycle your ignition key from off to on (not start) 3 times leaving it on. You then count the number of times the Service Engine Soon light flashes. This combination of flashes identifies a fault code. For example, a code 21 would be flash, flash, pause, flash. All codes are 2 digits. Multiple codes are seperated by longer pauses. It should end with a code 55 indicating the process is finished.

Sometimes in newer models, the code is shown on the trip odometer. They would be P codes.

I would pull out my obd code reader and find out what it's telling me. Some parts places (Autozone, O'Reilys, etc) would even have a code reader you could borrow to check for any obd codes.

Jun 07, 2008 | 2005 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...