Question about 2006 GMC Sierra

1 Answer

My 2006 gcm 2500 4 door truck back doors will not lock when i use my remote key or when i put it in gear

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 750 Answers

There is a power motor thats conected to the main lock drag link via a sub drag link which are clamped together some time the clamp gets loose and slides on main drag link and when activated dose not go through its corect range of travel ,engageing lock partly or not at all. you would have to remove the door trim to acsess it.

Posted on Oct 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I program the keyless remote on a 2006 Buick LaCrosse


2006 Buick Rendezvous Remote Programming For Buick Rendezvous / Intrigue / AztekObtain all remote transmitters for this vehicle.
1. Close all doors.
2. Press and hold the Unlock button on door lock switch on drivers door.
Hold until instructed to release in step 6.
3. Insert key into the ignition cylinder but do not turn it.
4. Remove key from ignition and then insert key into ignition without turning ignition cylinder and remove key.
5. Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.
6. Release door lock switch on drivers door panel. A Chime will sound 3 times indicating that you are in programming mode.
7. Press both the Lock and Unlock buttons on the remote up to 30 seconds.
A chime will sound 2 times if remote has programmed successful.
8. Repeat step 7 if you are programming additional remotes.
9. Remove key from ignition to exit programming mode

Oct 28, 2017 | Buick Cars & Trucks

2 Answers

2001 Chevrolet Impala Keyless Entry


Common problem, a small switch in the door lock breaks and does not activate the lock, all works from the key not remote, driver door recognises door not locked will unlock all doors, to repair you have to replace drivers door lock or just live with the key, I do
Merry Christmas

Dec 15, 2013 | 2001 Chevrolet Impala

1 Answer

Rear doors dont lock with auto lock switch on ram 2500 slt


Check the wiring harness into the rear doors - they tend to get crimped and break the wires

Feb 04, 2013 | 2006 Dodge Ram 2500

1 Answer

On my 2006 Chrysler 300/ the auto lock button on my key remote doesn't lock or unlock doors?


how do I reset one of two keys that the unlock,lock,trunck does't work but the key turns the engine over.

Oct 08, 2012 | 2006 Chrysler 300

1 Answer

2006 325 i door locks not working driver door will lock and other doors stay open if drivers door is locked it needs to be open manually back doors were locked by hand and now wont open by remote


I had a very similar situation. Was very annoying not being able to unlock or lock doors from pannel control nor from remote.
Only driver door can be opened with manual key.

Solution: One of the 15 amp purple fuses was blown. Fuses are located inside glove compartment, the interior end has to be removed releasing the two locks.
Use a light and the red tool located on the panel to remove fuses.

Oct 14, 2010 | 2006 BMW 3 Series

1 Answer

My truck fuel pump willnot come on and i replaced it also the fuel pump relay switch it look,s the fuel pump fuse has no power help


"if this truck has a factory theft deterrent mode" it cuts off the signal to your pump. Take the battery cable off and let sit for 30 minutes, hook it back up now using a "new key" with the resistor pellet in it put it in to the start position, and wait ten minutes now turn off , now see if the doors can be locked and unlocked with the remote fob...close all doors and use remote fob to lock the doors. now using just the key unlock your drivers door. Now give it a shot and see if it will start. sorry but this is all i can come up with right now..what usually most people end up doing is to tow it to the dealer, and they have a special box with your code that resets the theft mode.

May 10, 2010 | 1994 Chevrolet Silverado 2500

3 Answers

My wife is stuck at the airport. the key fob on


On the driver's side door handle, there is a cap covering the key hole on the right side. On the bottom of the cap is a small ****. Use the valet key to pry it up and off. Then you may open the door, most likely sounding the alarm, so you will need to insert the remote in the ignition to stop the NOISE!!!! Hope this helps. This is how I lock my remote away when I go somewhere to run.

Nov 06, 2009 | 2006 Volkswagen Passat

1 Answer

2001 silverado 2500 HD diesel. Key goes in, will


I believe that the vehicle antitheft is tied into the drivers door lock. Maybe try disconnecting the battery for 2 minutes.

Oct 24, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

Sliding door will not lock or unlock with remote key or front door panels


I have the same van and the passenger side sliding door stopped locking by the remote or the electrical switch. I took the door panel off for the sliding door and located the door lock solenoid( the locking solenoid was bad). but it was sOOOOOO dificult to remove the door lock solenoid ( and I thought I had every tool) that I had no choice but to put it all back together and tell the wife she needed to take it to the dealership to fix it. I forget how much the part was but the dealer part was suprisingly more expensive than I thought it would be.

Jun 10, 2009 | 2006 Chrysler Town & Country

2 Answers

1999 Ford Explorer Door Locks


Unfortunately, This is a very common problem with Ford Explorers! Ford replaces the locks when it encounters this issue. I managed to unseize my passanger door and tailgate lock, but the drivers door lock is broken beyond repair. You can purchase new remotes for your explorer and program them very easily. Just google ford key fobs...

Jan 03, 2009 | 1999 Ford Explorer

Not finding what you are looking for?
2006 GMC Sierra Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...