Question about 2004 Audi A4

2 Answers

How do I bleed the front brakes on a 2004 audi a4 quattro?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,874 Answers

For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Posted on Oct 01, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 750 Answers

Start car,trany in park and placing a clear tube on bleed valve with the other end in a container with clean fluid, have an assistant depress pedalfully as you open bleed valve,(do not pump pedal) when pedal reaches full strok(to the floor) close valve and then release pedal keep doing this till air free fluid is seen coming from bleed line, start with wheel furthest frommaster cylinder

Posted on Oct 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove dash panel to replace brake light switch 2004 a4 quattro 1.8


Its beneath the brake pedal not dash. Do not depress it before installation as it will lock up and cannot be used after.

Jun 19, 2014 | 2004 Audi A4

1 Answer

Hi I own an audi a4 2004 Quattro, and i been having problems after i changed my break pads recently. Everytime i break, when going on low speed, there's a clunking sound coming from both, left and right...


um, clunking brakes when braking after you repaired them? EMERGENCY PROCEDURE REQUIRED Have the car towed to a reputable shop. Your brake pads or calipers or wheel are coming apart. they could fail while driving. This is likely very serious. Hopefully, it is just the anti rattle clips not holding the pads in place but do not chance it. Also, consider a mobile mechanic

Jul 22, 2017 | 2004 Audi A4

1 Answer

How do i change front brake hose on my 98 audi a4? where is it located?


Its located on the brake caliper and goes up to the brake line,To change just remove the high pressure fitting from both ends [very basic job]Fit the new pipe ,but now you have a new pipe but full of air!.To bleed out the new pipe just open the bleed screw [looks like a grease nipple on the top of the brake caliper]and connect a small piece of hose [must be a tight fit on the bleed screw]with the bleed screw loose and the hose fitted just fit the other end in to a container of brakefluid and press the brake slowly up and down till all the bubbles are gone{dont forget to top up your reservoir before you bleed it!!]as if the reservoir runs dry you will need a special bleeder to bleed the brakes [it requires 2 bar or 30 psi pressure to bleed out the system after the reservoir goes dry]

Mar 08, 2010 | 2004 Audi A4

1 Answer

Squeek noise on front wheels when hit bump


The problem could be caused by a wheel bearing squeeling or the cv joint squeeling.

Jun 25, 2009 | 2000 Audi A4

2 Answers

How to depress rear brake caliper piston on an 2004 Audi A4


It must be turned clockwise while being pushed in. The local parts store will have a tool just for this purpose.

Mar 27, 2009 | 2004 Audi A4

1 Answer

The tail lights to my Audi A4 quattro 2.0 T wont turn off


common for the brake lights to stay on but not tail lights are you sure its tail lights ? if it is are the front side lights on ?

Jan 01, 2009 | 2006 Audi A4

1 Answer

Replacing the brake bulb in my Audi A4 Quattro


There is a small carpeted circle that pops out, unscrew 1 phillips head screw and the tail-light releases

Nov 22, 2008 | 2004 Audi A4

1 Answer

I want to replace the rear disk pads on my a-6 Quattro 3.0; can I safely use one of those compressor kits from a parts place to compress the pistons, any tricks to share ?? and anything to worry about...


I have taken the brake caliper of the rear passenger side and renewed the seals in it i have also renewed the brake pads in that wheel i have tried to bleed it before renewing the pads in the outherside but when i open the bleed nipple and push the peddle down there is no braked fluid coming out i also renewed the nipple.When you take the brake pipe off the caliper ther is still no fluid coming out also there is no pressure on the pedal 1997 audi a4 1800

Jul 26, 2008 | 1998 Audi A4

Not finding what you are looking for?
2004 Audi A4 Logo

358 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14223 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...