Question about 1994 Honda Accord

1 Answer

Leaking oil from behind crank pully - 1994 Honda Accord

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 750 Answers

Frontseal is worn remove pully and replace

Posted on Oct 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have oil leaking from either the timing chain 4.6l 32v oil get on the fan belt


it would be the timing chain cover or the crank sensor on the lower right front of engine to the side of your crank pully

May 06, 2014 | 2000 Chevrolet Blazer

1 Answer

Oilpan at crank leaking when starting up vann what is seal or pan gasket


the oil pan is the pan that you see under the car it is what seals the pan to the
motor thare is a gasget between them with a sealer //front and rear seals
thare is 1 behind the harmonic balancer or the bottom pully the fan belt goes
to the other is in front of the fly wheel the fly wheel is what the starter engages
to when starting your car the front and rear seal fit around the crank shaft
to real oil in i hope this helps you bob
10_16_2011_3_51_51_pm.jpg10_16_2011_3_52_06_pm.jpg

Oct 09, 2011 | 1998 Plymouth Voyager

2 Answers

How do i repair the gasket behind the crank shaft seal?I have a major oil leak and i was told my gasket behind the crank shaft in the front needs to be changed. I have nearly no experience on vehicles so...


Front crank seal. First you have to have room to work, so this may require you remove the radiator and some plastics. Remove the serpentine belt,remove the bolt in the center of the crank pully. The pully should slide off with some resistance but not enough to need a puller. Once the pully is off, there's your sea. Pop the seal out with a screwdriver. Clean the surface of the hole where the seal was, Put some sealer,on the outer perimeter of the new seal and some grease on the seal lips. Evenly tap the new seal into place with the spring side of the seal facing in. make sure seal is at the point the old seal was. Now take the pully and clean the surface the seal rides on, very clean and nd coat with a thin coating of grease. Slide the pully back on and secure with bolt. Then belt, then radiator. Any trouble, holler. Good Luck, Ned

Oct 17, 2009 | 1994 Dodge Caravan

1 Answer

Describe your 2005 Chrysler Town & Country Problem HOW DIFFICULT IS IT TO CHANGE FRONT CRANK SEAL?


it's not too bad to change, you will need a special tool to remove the crank pully, it looks like a 3 jaw puller and once you get that off the seal is right behind it. Make sure to clean the crank pully shaft that goes through the seal with a piece of emery cloth to prevent leakage and coat it with either transmission assembly lube or a small amount of motor oil to prevent a dry start that can damage the seal again

Jul 23, 2009 | 2005 Chrysler Town & Country

1 Answer

Major oil leak


check front crank seal ive replaced lots of those and you may have to sleeve the crank pully

May 31, 2009 | 2003 Chevrolet Silverado 1500

2 Answers

Antifreeze drips from crank shaft pully area when running.


it's probably not dripping from the crankshaft... it would drip from the water pump just on top of it...

to check if it is done, take a flashlight and spot on top of the water pump. there should be a hole on top of it behind the pulley...

if it is damp, the pump is gone....

if not it might leak from the gasket...

Apr 28, 2009 | 1986 Acura Integra

1 Answer

Oil leaking from front of motor.


Being it is a 97 outbac, I believe you have the EJ25 Duel over head cam Boxer motor, Very good motor. If i am correct you have 5 places that most likely could be the leak. THe crank pulley, in center, Or either of the 4 cam shafts. You will have to look for more signs of the leak. If leaking from the cams you will usualy see the oil on the iside of the pulleys them selves. The crank seal on the other hand generally runs down the center of the block.Please be very careful to check your timing marks on your pulleys before you start it, due to the belt posibly slipping from what you had said. The crank has a small hash line that points up to a mark in the block The top pulleys on both sides have a sigle line that points to a notch straight up on the cover and double lines that point straght down at double lines on the lower pulleys. And the lower pulleys also have a single line that point to a notch outward that is on the cover. Hope this helps and have a good day.

Jan 30, 2009 | 1997 Subaru Outback

Not finding what you are looking for?
1994 Honda Accord Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...