Question about 2001 Chevrolet Venture

2 Answers

Where does the vacuum line on air intake duct

Where does the vacuum line on air intake duct connect to on a 2001 chevy venture?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 19 Answers

Are you referring to the plastic line that comes out of the top of the duct, turns and disappears toward the back of the engine? That line goes to the top of the rear valve cover. Use a flashlight and look for the hole on the top of the back valve cover. Look to the right and below the coils. It's tough to see but you can see it. Be careful, sometimes the plastic line can be brittle and break.

Posted on Oct 01, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

It is really hard to reach and see. I finally figured out if you reach over the distributor, down, and back toward said valve cover you can reach where it plugs in.

Posted on Jan 20, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 bmw 530i heat only comes out defroster all others blow cold , vents are working redirecting air flow , any thoughts


sounds like a trap door is stuck not allowing the heat to flow through your air duct properly ..check for any bad vacuum leaks around your intake or around your air flow leading to intake vacuum

Oct 26, 2013 | 2001 BMW 325

1 Answer

My a/c is blowing cool air on the pax side and, warm on the driver side of my Chevy Venture Van, what can I do, to fix this problem


The fact that its blowing cold on one side means that the AC system is working correctly . However the air flow is controled by vacuum actuators inside the the dash board . There controled by engine vacuum and open and close little dors inside the duct work that roots the air into the cabin . Unfortinatly there not always that easy to get to with out removeing the the dash .Look up under the dask try to follow the duck work it may be just stuck or a disconnected hose or a split hose But your AC system is working and this is where the problem is . Good luck with it

Aug 14, 2011 | 2001 Chevrolet Venture

1 Answer

Need to replace intake manifold how do you do this


Bonneville, LeSabre, Park Avenue 2000-2005 Intake Manifold - Removal & Installation

3.8L Engine
VIN 1 Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    Negative battery cable Supercharger Thermostat housing Exhaust Gas Recirculation (EGR) tube at the intake manifold Engine Control Temperature (ECT) sensor Intake manifold
To install:
  1. Install or connect the following:
    Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm). ECT sensor connector EGR tube to the intake manifold Thermostat housing Supercharger Negative battery cable
  2. Refill and bleed the cooling system.
  3. Run the engine and check for leaks and proper engine operation.

VIN K Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Relieve the fuel system pressure.
  5. Remove or disconnect the following:
    Fuel injector sight shield Air inlet duct Spark plug wires from the right side Manifold Absolute Pressure (MAP) sensor Vacuum lines from the intake manifold Fuel lines Fuel injector electrical connectors Fuel regulator vacuum line Fuel rail from the intake manifold Exhaust Gas Recirculation (EGR) heat shield Throttle cable bracket from the cylinder head mounting bracket and the throttle body cables Throttle body support bracket Upper intake plenum and gasket Thermostat housing Electrical connector from the Engine Coolant Temperature (ECT) sensor Drive belt tensioner assembly EGR valve outlet pipe Lower intake manifold

    a5adffa.jpg
    Fig. Exploded view of the intake manifold and related components-3.8L (VIN K) engine
To install:


140d431.jpg
Fig. Upper intake manifold torque sequence-3.8L (VIN K) engine


4950e4f.jpg
Fig. Lower intake manifold torque sequence-3.8L (VIN K) engine
  1. Install or connect the following:
    Intake manifold using new manifold gaskets. Torque the bolts in sequence to 11 ft. lbs. (15 Nm); then, re-torque to 11 ft. lbs. (15 Nm). EGR valve outlet pipe Drive belt tensioner assembly. Torque the tensioner bolts to 37 ft. lbs. (50 Nm). Electrical connector to the ECT sensor Thermostat housing Upper intake plenum. Torque the intake plenum bolts to 88 inch. lbs. (10 Nm). Throttle body support bracket Throttle cable bracket to the cylinder head mounting bracket and the cables to the throttle body lever EGR heat shield Fuel rail. Torque the fuel rail bolts to 88 inch. lbs. (10 Nm). Fuel lines Fuel regulator vacuum line Fuel injector electrical connectors Vacuum lines to the intake manifold MAP sensor Spark plug wires Fuel injector sight shield and air inlet duct Negative battery cable
  2. Refill and bleed the cooling system.
  3. Run the engine and check for leaks and proper engine operation.

Hope this help (remember rated this).

May 17, 2010 | 2001 Pontiac Bonneville

1 Answer

How do you install injectors in a chevy s-10 pick-up?


Removal & Installation

8205896.gif
Exploded view of the fuel rail and injector mounting


Take care when servicing the fuel rail assembly to prevent dirt or contaminants from entering the fuel system. ALL openings in the fuel lines and passages should be capped or plugged while disconnected.
  1. Before disassembly, clean the fuel rail assembly with a spray type cleaner such as AC Delco® X-30A, or equivalent. After removal, DO NOT immerse the fuel rail in liquid solvent.
  2. Properly relieve the fuel system pressure and disconnect the negative battery cable.
  3. Remove the air intake duct, as necessary for access.
  4. Tag and disengage the fuel injector electrical connectors.
  5. Disengage the fuel pressure regulator vacuum line, then tag and disengage all other necessary vacuum hoses.
  6. Loosen and remove the fuel rail retaining bolts.
  7. If necessary to remove the fuel rail assembly completely from the engine compartment, or to prevent stressing and damaging the fuel lines, disconnect the fuel lines from the rail assembly.
  8. Carefully lift the fuel rail assembly and fuel injectors from the intake.
  9. Carefully release and separate the fuel injectors from the rail assembly.
  10. Remove and discard ALL old O-rings from the fuel injectors and, if disconnected, the fuel lines.
To install:
  1. Lightly coat the new O-rings with clean engine oil, then position them to the injectors and, if applicable, fuel fittings.
  2. Install the injectors to the fuel rail assembly.
  3. Carefully install the fuel rail and injectors to the intake manifold. Make sure the injectors are properly seated in their bores, but DO NOT force them into position.
  4. Install and tighten the rail retaining bolts to 62 inch lbs. (7 Nm).
  5. If removed, connect the fuel lines to the rail assembly and secure the fittings.
  6. Engage the fuel pressure regulator and any other vacuum lines, as noted during removal.
  7. Engage the injector electrical connectors.
  8. Connect the negative battery cable and cycle the ignition switch (without attempting to start the engine) in order to pressurize the fuel system, then check for leaks.
  9. Install the air intake duct.

Apr 25, 2010 | 1992 Chevrolet S-10

1 Answer

2001 Chevy Venture will not start. Turns over and tries to start


Spray "starting fluid" (AutoZone $4) into air intake. If it "starts better" then it is fuel-related. The gas in your tank may be contaminated. Whatever floated to the top is what is left in your tank. Add a gallon of new fuel, burn what you can and use a "complete fuel system cleaner" (AutoZone $9) when you fill-up.

Oct 05, 2009 | 2001 Chevrolet Venture

1 Answer

How do I remove the thermostat from my 2001 chevy venture


2001 Chevrolet Truck Venture FWD 3.4L SFI 6cyl

Removal & Installation

  1. Remove the air cleaner and duct assembly.
  2. Drain the coolant until the coolant level is below the thermostat.
  3. Remove the crossover exhaust pipe.
  4. Remove the radiator hose from the thermostat housing.
  5. Remove the thermostat housing bolts and clean any sealer from the bolt threads.
    30d8f30.jpg

    Fig. Remove the housing bolts
  6. Remove the thermostat housing and gasket.
  7. Remove the thermostat.
  8. Clean the mating surfaces.

To install:


6c98478.jpg

Fig. The removal and installation of the thermostat
  1. Install the thermostat.
  2. Install the thermostat housing and gasket.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the thermostat housing bolts and tighten them to 18 ft. lbs. (25 Nm).
  4. Install the radiator hose to the thermostat housing.
  5. Install the crossover exhaust pipe.
  6. Install the air cleaner and duct assembly.
  7. Fill the cooling system.

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the air cleaner intake duct.
  3. Partially drain the cooling system.
  4. Remove the radiator inlet hose from the thermostat housing.
  5. Remove the thermostat housing bolts.
  6. Remove the thermostat.
  7. Clean and inspect the thermostat housing gasket mating surfaces.
To install:
  1. Install the thermostat.
  2. Install the thermostat housing.
  3. Install the thermostat housing bolts and tighten to 18 ft. lbs. (25 Nm).
  4. Install the radiator inlet hose to the thermostat housing.
  5. Install the air cleaner intake duct.
  6. Fill the cooling system.
  7. Start the engine and check for leaks.
3.9L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Release the tension on the hose clamp at the thermostat housing and remove coolant hose.
  4. Remove the thermostat housing mounting bolts and remove the thermostat housing.

    5734720.jpg
    Fig. Remove the thermostat housing to access the thermostat-3.9L engine shown
  5. Remove the thermostat.
To install:
  1. Install the thermostat.
  2. Install the thermostat housing and tighten the bolts to 18 ft. lbs. (25 Nm).
  3. Install the coolant hose to the thermostat housing and install the hose clamp.
  4. Refill the cooling system to the correct level.
  5. Start the engine and check for leaks.

I hope help you whit thie (remember rated this help) Have a nice day and good luck.

Sep 23, 2009 | 2001 Chevrolet Venture

2 Answers

Radiator replacement


  1. Remove air cleaner and duct assembly.
  2. Drain the coolant.
    1. Remove the engine mount struts.
    2. Remove the cooling fans with the cooling fan shroud.
    3. Remove the radiator upper hose from the radiator.
    4. Remove the radiator lower hose from the radiator.
    5. Disconnect the transaxle oil cooler lines from the radiator.
    6. Remove the radiator brackets and bolts.
    7. Remove the radiator. Installation Procedure
    1. Install the radiator. Notice: Refer to Fastener Notice in Service Precautions.
      1. Install the radiator brackets and bolts.
        • Tighten the bolts to 24 Nm (18 ft. lbs.) .
      1. Connect the transaxle oil cooler lines to the radiator.
      2. Install the radiator upper hose to the radiator.
      3. Install the radiator lower hose to the radiator.
      4. Install the cooling fans with the cooling fan shroud.
      5. Install the engine mount struts. Notice: When adding coolant, it is important that you use GM Goodwrench DEX-COOL (R) or HAVOLINE (R) DEX-COOL (R) coolant. If Coolant other than DEX-COOL (R) or HAVOLINE (R) DEX-COOL (R) is added to the system the engine coolant will require change sooner; at 50,000 km (30,000 mi) or 24 months.
      6. Fill the cooling system.
      7. Install the air cleaner and duct assembly.

Jun 28, 2009 | 2000 Chevrolet Venture

2 Answers

Where is thermostat on 2001 chevy venture van with v6 engine


under the intake plenum, which will have to be removed before you can access the thermostat.
I suggest having it done by a garage mechanic.

May 23, 2009 | 2004 Chevrolet TrailBlazer

Not finding what you are looking for?
2001 Chevrolet Venture Logo

Related Topics:

317 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

79077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...