Question about 1992 Ford Escort 4 Door

1 Answer

Timing belt won't tighten - 1992 Ford Escort 4 Door

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 80 Answers

If you have a 1.8L DOHC you need to buy a tensioner spring.
but if you have a 1.9L SOHC you need to pry the tensioner close to the belt to release the slack.

Let me know if this help you....

Posted on Sep 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i tighten the timing belt on my 1989 pontiac


I assume you are replacing the belt and also the waterpump, the waterpump is what tightens the timing belt, it spins in the housing in an oval shaped housing and tightens or loosens the belt, you need to loosen the waterpump bolts and rotate the pump to tighten the timing belt, make sure theres a small amount of slack in the belt after you tighten it, you dont what the belt too tight, you should be able to grab belt and move in and out an inch. heres a diagram to make sure all timing marks are lined up. note if the timing belt is being replaced you really should install a new waterpump and check the timing pulleys. good day.
10_26_2011_7_29_24_pm.gif

Oct 26, 2011 | 1989 Pontiac LeMans

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

2 Answers

Need diagram to put timingbelt on 2001 kia sportage


prev.gif next.gif Timing Belt Removal & Installation SOHC To Remove:
  1. Disconnect battery negative cable.
  2. Remove fresh air duct.
  3. Drain engine coolant into an appropriate container and retighten radiator drain plug.
  4. Remove upper radiator hose.
  5. Remove fan clutch assembly bolts.
  6. Remove 5 cooling fan shroud bolts.
  7. Remove fan shroud and fan as an assembly.
  8. Loosen alternator mounting bolts and remove drive belt from pulley.
  9. Remove fan pulley.
  10. Remove 4 cooling fan assembly bolts.
  11. Remove cooling fan assembly.
  12. Remove 4 bolts and upper timing belt cover.
  13. Remove 2 lower bolts and lower timing belt cover.
  14. Loosen adjusting bolt and remove A/C belt.
  15. Remove alternator belt.
  16. Loosen power steering pump lock bolt and mounting bolt.
  17. Remove drive belt from crankshaft damper. Camshaft timing marks kia-03-20-7032.gif

  18. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
  19. Remove 5 bolts and remove damper.
  20. Remove timing belt guide from timing belt pulley.
  21. Loosen tensioner lock bolt.
  22. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt. NOTE: Mark the direction of timing belt rotation on the belt if it is being reused.
  23. Remove timing belt.
To Install:
Timing belt pulley timing marks kia-03-20-7035.gif

NOTE: Timing belt pulley timing mark and timing mark must be aligned.
Camshaft timing marks kia-03-20-7032.gif

NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
Timing belt installation kia-03-20-7036.gif

  1. Install timing belt with minimal slack from timing belt pulley to water pump and from water pump to camshaft pulley.
  2. Loosen tensioner lock bolt until tension is applied to timing belt. CAUTION
    Do not turn crankshaft counterclockwise.
  3. Turn crankshaft pulley 2 full turns clockwise and ensure timing marks are properly aligned.
  4. Tighten tensioner lock bolt to 33 ft lb (45 Nm).
  5. Apply a force of 21 lb to timing belt midway between idler pulley and camshaft pulley.
    • Deflection should measure 0.43-0.51 inch (11-13 mm)
    NOTE: if timing belt deflection is incorrect remove timing belt and install NEW tensioner spring.
  6. Install timing belt guide.
  7. Install crankshaft damper pulley.
  8. Install 5 crankshaft damper pulley bolts. Tighten bolts to 132 in lb (15 Nm).
  9. Install power steering pump drive belt.
  10. Adjust power steering pump drive belt tension and tighten lock bolt and mounting bolt.
  11. Install alternator drive belt.
  12. Install A/C drive belt.
  13. Install lower timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
  14. Install upper timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
  15. Install cooling fan assembly and 4 bolts. Tighten bolts to 27 ft lb (37 Nm).
  16. Install fan pulley.
  17. Install fan clutch and shroud as an assembly. Tighten bolts to 74 in lb (8 Nm).
  18. Tighten 4 cooling fan nuts to 16 ft lb (22 Nm).
  19. Adjust alternator belt tension and tighten alternator mounting bolts.
  20. Install upper radiator hose.
  21. Install fresh air duct.
  22. Connect battery negative cable.
  23. Refill/bleed cooling system.
DOHC To Remove:
  1. Disconnect battery negative cable.
  2. Remove fresh air duct.
  3. Remove 5 cooling fan shroud bolts and 4 thermo-modulated fan nuts.
  4. Remove 4 thermo-modulated fan shroud fasteners.
  5. Remove generator drive belt.
  6. Remove fan pulley (located above crankshaft pulley).
  7. Remove 4 bolts and splash shield (located under front of vehicle).
  8. Remove A/C drive belt and power steering drive belt. Timing Belt Removal kia-03-20-7097.gif

  9. Remove 5 bolts and upper timing belt cover.
  10. Remove 2 bolts and lower timing belt cover.
  11. Loosen tensioner lock bolt and pivot tensioner pulley outboard.
  12. Retighten tensioner lock bolt. NOTE: Mark timing belt for rotation if it is being reused.
  13. Remove timing belt.
To Install:
Crankshaft match marks 79245g25.gif

  1. Align marks on timing belt pulley and pump body. Camshaft pulley alignment marks 79245g28.gif

  2. Align marks on camshaft pulleys with alignment marks on seal plate.
  3. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  4. Loosen tensioner lock bolt.
  5. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  6. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  7. Apply a force of 22 lbs to timing belt between camshaft sprockets.
    • Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
    NOTE: Replace tensioner spring if timing belt deflection is excessive.
    Timing Belt Installation kia-03-20-7097.gif

  8. Install lower timing belt cover.
  9. Install upper timing belt cover.
  10. Install power steering drive belt and adjust belt tension.
  11. Install fan pulley.
  12. Install generator drive belt and adjust belt tension.
  13. Install A/C drive belt and adjust belt tension.
  14. Install splash guard.
  15. Install fan and fan shroud.
  16. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  17. Install fan shroud mounting bolts.
  18. Install fresh air duct.
  19. Connect hose to resonance chamber.
  20. Connect battery negative cable.

Aug 02, 2010 | 2001 Kia Sportage

2 Answers

How do i put timing belt and water pump?


REMOVAL & INSTALLATION of timing belt: Fig. 1: View of the timing belt cover 91163p64.gif
Fig. 2: Loosen then timing belt tensioner using a ratchet and short socket 91163p65.gif
Fig. 3: Matchmark the direction of rotation of the timing belt 91163p67.gif
Fig. 4: Once loose, pull the belt off the camshaft pulley 91163p71.gif
  1. Disconnect the negative battery cable.
  2. Turn the crankshaft to align the timing belt matchmarks and set cylinder No. 1 to Top Dead Center (TDC) on the compression stroke. Once in this position, the engine must NOT be turned or disturbed.
  3. Remove all necessary components to gain access to the cylinder head and timing belt covers.
  4. Remove the cylinder head and timing belt covers.
  5. There are 2 belts in this system; the one running to the camshaft pulley is the timing belt. The other, shorter one drives the balance shafts and is referred to as the balancer belt or timing balancer belt. Lock the timing belt adjuster in position by installing one of the lower timing belt cover bolts to the adjuster arm.
  6. Loosen the timing belt and balancer shafts tensioner adjuster nut, but do not loosen the nut more than 1 turn. Push the tensioner for the balancer belt away from the belt to relieve the tension. Hold the tensioner and tighten the adjusting nut to hold the tensioner in place.
  7. Carefully remove the balancer belt. Do not crimp or bend the belt; protect it from contact with oil or coolant. Slide the belt off the pulleys.
  8. Remove the balancer belt drive sprocket from the crankshaft.
  9. Loosen the lockbolt installed to the timing belt adjuster and loosen the adjusting nut. Push the timing belt adjuster to remove the tension on the timing belt, then tighten the adjuster nut.
  10. Remove the timing belt. Do not crimp or bend the belt; protect it from contact with oil or coolant. Slide the belt off the pulleys.
  11. If defective, remove the belt tensioners by performing the following:
    1. Remove the springs from the balancer belt and the timing belt tensioners.
    2. Remove the adjusting nut.
    3. Remove the bolt from the balancer belt adjuster lever, then remove the lever and the tensioner pulley.
    4. Remove the lockbolt from the timing belt tensioner lever, then remove the tensioner pulley and lever from the engine.
  12. This is an excellent time to check or replace the water pump. Even if the timing belt is only being replaced as part of a good maintenance schedule, consider replacing the pump at the same time. To install:
  13. If the water pump is to be replaced, install a new O-ring and make certain it is properly seated. Install the water pump and retaining bolts. Tighten the mounting bolts to 106 inch lbs. (12 Nm).
  14. If the tensioners were removed, perform the following to install them:
    1. Install the timing belt tensioner lever and tensioner pulley. NOTE: The tensioner lever must be properly positioned on its pivot pin located on the oil pump. Be sure that the timing belt lever and tensioner moves freely and does not bind.
    2. Install the lockbolt to the timing belt tensioner, do not tighten the lockbolt at this time.
    3. Install the balancer belt pulley and adjuster lever.
    4. Install the adjusting nut and the bolt to the balancer belt adjuster lever. Do not tighten the adjuster nut or bolt at this time. NOTE: Be sure that the balancer lever and tensioner moves freely and does not bind.
    5. Install the springs to the tensioners.
    6. Move the timing belt tensioner its full deflection and tighten the lockbolt.
    7. Move the balancer its full deflection and tighten the adjusting nut.
  15. The crankshaft timing pointer must be perfectly aligned with the white mark on the flywheel or flex-plate; the camshaft pulley must be aligned so that the word UP is at the top of the pulley and the marks on the edge of the pulley are aligned with the surfaces of the head.
  16. Install the timing belt over the pulleys and tensioners.
  17. Loosen the bolt used to lock the timing belt tensioner. Loosen, then tighten the timing belt adjusting nut.
  18. Turn the crankshaft counterclockwise until the cam pulley has moved 3 teeth; this creates tension on the timing belt. Loosen, then tighten the adjusting nut and tighten it to 33 ft. lbs. (45 Nm). Tighten the bolt used to lock the timing belt tensioner.
  19. Realign the timing belt marks, then install the balancer belt drive sprocket on the crankshaft.
  20. Align the front balancer pulley; the face of the front timing balancer pulley has a mark, which must be aligned with the notch on the oil pump body. This pulley is the one at 10 o'clock to the crank pulley when viewed from the pulley end.
  21. Align the rear timing balancer pulley (2 o'clock from the crank pulley) using a 6 x 100mm bolt or rod. Mark the bolt or rod at a point 2.9 in. (74mm) from the end. Remove the bolt from the maintenance hole on the side of the block; insert the bolt or rod into the hole. Align the 2.9 in. (74mm) mark with the face of the hole. This pin will hold the shaft in place during installation.
  22. Install the balancer belt. Once the belts are in place, be sure that all the engine alignment marks are still correct. If not, remove the belts, realign the engine and reinstall the belts. Once the belts are properly installed, slowly loosen the adjusting nut, allowing the tensioner to move against the belt. Remove the pin from the maintenance hole and reinstall the bolt and washer.
  23. Turn the crankshaft 1 full turn, then tighten the adjuster nut to 33 ft. lbs. (45 Nm). Remove the bolt used to lock the timing belt tensioner.
  24. Install the lower cover, ensuring the rubber seals are in place. Install a new seal around the adjusting nut, DO NOT loosen the adjusting nut.
  25. Install the key on the crankshaft and install the crankshaft pulley. Apply oil to the bolt threads and tighten it to 181 ft. lbs. (250 Nm).
  26. Install the upper timing belt cover and all applicable components. When installing the side engine mount, tighten the bolt and nut attaching the mount to the engine to 40 ft. lbs. (55 Nm) and the through-bolt and nut to 47 ft. lbs. (65 Nm).
  27. Connect the negative battery cable.
---
For water pump removal and installation contact me:

Jul 12, 2010 | 1997 Honda Civic

2 Answers

Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


Hi,


You find the timing marks on the picture below.

moz-screenshot-2.pngaab8238.jpg



Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Jun 25, 2010 | 1997 Toyota Camry

1 Answer

Ifailed to get on tdc before removing old timing belt how do I get back in time so Icanreplacebelt.


This is the complete procedure from the service manual on how to replace the timing belt start to finish, start over to assure u get it right, if u mess up the engine will be damaged

Removal for 1.6L engines : ONLY 2006 to 2009 CARS


Engine removal is not required for this procedure.

1.Remove the engine cover.

2.Remove the RH front wheel.

3.Remove the 2 bolts and RH side cover.

4.Temporarily loosen the water pump pulley bolts.

5.Remove the alternator drive belt

6.Remove the air conditioner compressor drive belt

7.Remove the power steering pump drive belt

8.Remove the 4 bolts and water pump pulley.

9.Remove the 4 bolts and
timing belt2_bing.gif upper cover

10.Turn the crankshaft pulley, and align its groove with timing mark "T" of the timing belt cover. Check that the timing mark of camshaft sprocket is aligned with the timing mark of cylinder head cover. (No.1 cylinder compression TDC position)

11.Remove the crankshaft pulley bolt and crankshaft pulley

12.Remove the crankshaft flange

13.Remove the 4 bolts and timing belt lower cover

14.Remove the timing belt tensioner and timing belt.

15.Remove the bolt and timing belt idler

16.Remove the crankshaft sprocket

17.Remove the cylinder head cover.

(1)Remove the wire harness bracket

(2)Remove the ignition coil.

(3)Remove the PCV (Positive Crankcase Ventilation) hose and the breather hose from the cylinder head cover

(4)Remove the engine cover bracket

(5)Loosen the cylinder head cover bolts and then remove the cover and gasket.

18.Remove the camshaft sprocket.

Hold the portion of the camshaft with a hexagonal wrench, and remove the bolt with a wrench and remove the camshaft sprocket.

INSTALLATION:

1.Install the camshaft sprocket and tighten the bolt to the specified torque.

(1)Temporarily install the camshaft sprocket bolt

(2)Hold the portion of the camshaft with a hexagonal wrench, and tighten the bolt with a wrench
Tightening torque :78.5 ~ 98.1N.m (8.0 ~ 10.0kgf.m, 57.9 ~ 72.3lb-ft)



2.Install the cylinder head cover.

(1)Install the cylinder head cover and bolts
Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

(2)Install the engine cover bracket

(3)Install the PCV(Positive Crankcase Ventilation) hose and breather hose to the cylinder head cover.

(4)Install the ignition coil.

3.Install the crankshaft sprocket

4.Align the timing marks of the camshaft sprocket and crankshaft sprocket with the No.1 piston placed at top dead center and its compression stroke.

5.Install the idler pulley and tighten the bolt to the specified torque.

Tightening torque :42.2 ~ 53.9N.m (4.3 ~ 5.5kgf.m, 31.1 ~ 39.8lb-ft)

6.Temporarily install the timing belt tensioner

7.Install the belt so as not give slack at each center of shaft. Use the following order when installing timing belt.
Crankshaft sprocket →idler pulley →camshaft sprocket →timing belt tensioner

8.Adjust the timing belt tension.

(1)Loosen the tensioner pulley mounting bolt and apply tension to the timing belt.

(2)After checking the alignment between each sprocket and each timing belt tooth, tighten the mounting bolt and one by one.

Tightening torque :19.6 ~ 26.5N.m (2.0 ~ 2.7kgf.m, 14.5 ~ 19.5lb-ft)

(3)Then recheck the belt tension.
Verify that when the tensioner and the tension side of the timing belt are pushed in horizontally with a moderate force [approx. 49N (11lb)], the timing belt cog end is aprox. 1/2 of the tensioner mounting bolt head radius (across flats) away from the bolt head center.

4)Timing belt tension measuring procedure
(by a sonic tension guage)
Rotate crankshaft in clockwise direction to set 1st piston on top dead center (TDC) and rotate crankshaft in counterclockwise to 90° then measure the belt tension in the middle of tension side span (in arrow direction of above illustration) by free vibration method.


9.Turn the crankshaft two turns in the operating direction (clockwise) and realign crankshaft sprocket and camshaft sprocket timing mark.


10.Install the timing belt lower cover with 5bolts

Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

11.Install the flange and crankshaft pulley, and then tighten crankshaft pulley bolt. Make sure that crankshaft sprocket pin fits the small hole in the pulley.

Tightening torque :137.3 ~ 147.1N.m (14.0 ~ 15.0kgf.m, 101.3 ~ 108.5lb-ft)

12.Install the timing belt upper cover with 4 bolts.

Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

13.Install the water pump pulley and 4 bolts.

14.Install the power steering pump drive belt

15.Install the air conditioner compressor drive belt

16.Install the alternator drive belt

17.Install the RH side cover with 2 bolts

18.Install the RH front wheel.


Tightening torque :88.3 ~ 98.1N.m (9.0 ~ 10.0kgf.m, 65.1 ~ 72.3lb-ft)

19.Install the engine cover with bolts.


Tightening torque :3.9 ~ 5.9N.m (0.4 ~ 0.6kgf.m, 2.9 ~ 4.3lb-ft)

May 20, 2010 | 2006 Kia Sorento

1 Answer

Need timing info on a 05/06 saturn ion? 2.0 l sprchrged eng



  • Tighten
    Tighten the timing belt tensioner fastening nut to 20 N·m (15 lb ft).
  • Verify the timing marks are still aligned.
  • Remove the J42069-10 and J42069-20.
  • Install the timing belt front cover. Refer to Timing Belt Cover Replacement-Front.
  • Connect the negative battery cable.Tighten
    Tighten the battery terminal bolts to 17 N·m (13 lb ft)

  • click on this link directly to get detailed instructions on how to set timing on Saturn Ion Car http://whoisbyme.blogspot.com/2010/03/saturn-ion-cars-trucks-timing-belt-20-l.html ------------ This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

    Mar 25, 2010 | Saturn Ion Cars & Trucks

    1 Answer

    How do i install a water pump for an Isuzu Rodeo, V.7 3.2 liter


    Isuzu_Rodeo_Rodeo_Sport_1997-2004
    Water Pump - Removal and Installation

    3.2L Engines
    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Drain the cooling system.
    3. Remove or disconnect the following:
      Negative battery cable Upper radiator hose Timing belt. Refer to the Timing Belt procedure. Idler pulley Water pump
    To install:


    d2081b9.jpg

    Fig. Exploded view of the water pump mounting

    3702807.jpg

    Fig. Water pump torque sequence. Apply LOCTITE® 262 to bolt number 3 (arrow)-3.2L and 3.5L engines

    NOTE Apply Loctite® 262 to bolt number 3 prior to installation.
    1. Install or connect the following:
      Water pump. Tighten the bolts in two passes, in sequence, to 18 ft. lbs. (25 Nm). Idler pulley. Torque to 38 ft. lbs. (52 Nm). Timing belt Upper radiator hose Negative battery cable
    2. Fill the cooling system.
    3. Start the engine and check for leaks.

    3.2L Engine
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Drain the cooling system.
    3. Remove or disconnect the following: Negative battery cableRadiator hoseAccessory drive beltFront coverTiming belt. Refer to the Timing Belt unit repair section.Timing belt idler pulley Water pump
      Negative battery cable Radiator hose Accessory drive belt Front cover Timing belt. Refer to the Timing Belt unit repair section. Timing belt idler pulley Water pump

    To install:

    e6f48ad.jpg

    Fig. Water pump bolt tightening sequence-3.2L engines
    1. Install or connect the following: Water pump. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm).Timing belt idler pulley. Tighten the bolt to 38 ft. lbs. (52 Nm).Timing beltFront coverAccessory drive beltRadiator hoseNegative battery cable
      Water pump. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm). Timing belt idler pulley. Tighten the bolt to 38 ft. lbs. (52 Nm). Timing belt Front cover Accessory drive belt Radiator hose Negative battery cable

    2. Fill the cooling system.
    3. Start the engine and check for leaks.

    Hope this help (remember rated and commento).

    Mar 19, 2010 | 1997 Isuzu Rodeo

    1 Answer

    Remove water pump


    Disconnect battery earth lead. Do not turn crankshaft or camshaft whn timing beld removed. Remove spark plugs to ease turning engine. Turn engine in normal direction of rotation (unless otherwise stated) Do not turn engine via camshaft or other sprockets. Observe all tightening torques. Remove engine, remve RH engine mounting. Remove auxiliary drive belts, water pump pulley, crankshaft pulley, timing belt upper cover, timing belt lower cover. Turn crankshaft clockwise to TDC on No. 1 cylinder, slacken tensioner bolts 5 & 6. Move tensioner away from belt and lightly tighten bolts. Remove timing belt. Remove water pump and replace with new one. Suggest to replace cambelt as well.
    Installation
    Ensure timing marks aligned3 & 4. Fit timing belt in anti-clockwise direction, standing at crankshaft sprocket. Ensure belt is taut between sprockets on non-tensioned side. Slacken tensioner bolt 5. slacken tensioner bolt 6. Allow tensioner to operate. Tighten tensioner bolt 6. Tighten tensioner bolt 5. Turn crankshaft on turn clockwise. Ensure crankshaft sprocket timing marks aligned 4.
    Slacken tensioner bolt 5. Slacken tensioner bolt 6. Allow tensioner to operate. Tighten tensioner 6. Tighten torque: 20 - 26 Nm. Tighten tensioner bolt 5. tighten torque: 20 - 26 Nm. Apply thumb pressure to belt at middle. Approximately 5kg. Belt should deflect to 1/4 of tensioner bolt head width 7. Belt tention can also be set using burroghs (BT-33-73F) tension gauge 10 at middle. Turn crankshaft 90 ° anti clockwise. Check belt tension is 9.5 16,5kg (engine must be cold). Install components in reverse order of removal. Fit cranckshaft pully. Tighten crankshaft pully bolts 8. G4-J: Tightening torque: 12-15Nm.
    G4-N/G4-k: Tightening torque: 10-12Nm
    G4EA: Tighten crankshaft pully bolt 9. Tighten torque: 140-150Nm.

    Nov 04, 2009 | Hyundai Excel Cars & Trucks

    2 Answers

    Need instructions to replace 1993 Toyota Camry Timing Belt


    Hi Kmcarroll77

    TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

    Installation
    1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

    CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
    4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
    CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
    9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
    b7619be.jpg
    92cabaf.jpg
    Hope this helps, don't forget to rate.

    Lazaruselite

    Feb 25, 2009 | 1993 Toyota Camry V6

    Not finding what you are looking for?
    1992 Ford Escort 4 Door Logo

    Related Topics:

    66 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76691 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    fordexpert

    Level 3 Expert

    5537 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...