Question about 1986 Ford Bronco II

1 Answer

I have an 86 ford bronco II. Ive been driving around with the tranny not going into 4th gear. Today I was driving and the tranny started to completely slip into 3rd gear, almost like going into neutral. The fluid was very low so I added some fluid along with Lucas Oil's transmission stop slip. Is there anything else I can do. I cannot afford a new trans.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 26 Answers

I would have to say no,there is nothing else you can do now. Does the fluid smell burned? Is it discoloured? If it is ok now after the top up and additive ,consider your self lucky.

Posted on Sep 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 86 ford bronco ii that recently i went to start and the idle was so erratic i thought had a vaccuum leak or something i ended up trying to drive it home and it had no power and would rev up b


I'd replace dist. cap and rotor button. There might also be a crankshaft position sensor near the crank. Might be bad. Also,check the MAP sensor and vacuum to it. don-ohio (:^)

Mar 26, 2017 | 1986 Ford Bronco II

1 Answer

We can get the 86 bronco II to start and run but will not go when put into drive or reverse?


Check your Transmission Fluid. If it is low fill to the recommended level. If it smells burnt it is time for a Rebuild.

May 14, 2014 | 1986 Ford Bronco II

1 Answer

1990 Ford Bronco II manual transmission extremely hard to shift will not go into reverse


90 Ford Bronco II: You have to put it in whichever gear you want it in before you start it or it wont shift at all. Then once you are going its extremely hard to shift into the other gears. Reverse is the only gear that sounds like its grinding.

Aug 16, 2013 | 1990 Ford Bronco II

1 Answer

Bronco II won't start


86 ford bronco 2 won't start changed coil wire acts like it wants to start not getting spark

Nov 10, 2012 | 1988 Ford Bronco II

1 Answer

Does an 86 ford bronco ii have more than 4 seats


all bronco II's that i have seen have 2 bucket seats up front and 1 bench in the back that usually had 3 sets of seatbelts.

May 20, 2010 | 1986 Ford Bronco II

1 Answer

TRANSMISSION


The two wheel drive tranny won't work because it will be longer. The tranny that came out of the 4 wheel drive is shorter and the transfer case bolts to the rear of the tranny thus it has a shorter output shaft and a different spline to accommodate the transfer case. You need to find the correct tranny unless you want to change the internals from one tranny to the other.

Feb 26, 2009 | 1988 Ford Bronco II

1 Answer

Vibrations in 4th gear and TCC lock-up


it does sound like the u joints
with the eggine turned off and in park craw under it and see if you can shake the drive shaft if you can shack it at all their wore, replace them

Feb 20, 2009 | 2001 Ford Focus

1 Answer

All gears grinding not going


You obviously need to bleed the line. You are not getting enough movement to disengage the pressure plate when depressing the clutch pedal. The systems can be a little tough to bleed air from. Keep at it. You will get it. The secret is to keep the reservoir full while bleeding and not let more air back it at the slave down below. Good luck.

Jan 15, 2009 | 1993 Ford Bronco

1 Answer

Ford transmission 86 4wd will not shift to high gear


It is hard to say from your description what the problem is ... could be linkage issue ... could be trans is going as is with the other poster ...
Losing overdrive. Clutches (bands/clutches) have had it. Be careful driving without that top gear ... doing too high a speed without the appropriate gear causes extra stress on your engine that could accelerate further problems. Try to do only driving at a low enough speed that the top gear is not missed ... will help the vehical last as long as possible.

Oct 13, 2008 | 1986 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...