Question about 1993 Chevrolet K1500

Open Question

Easy ways to replace oil cooler line in a truck

Oil cooler lines

Posted by on

  • yadayada
    yadayada May 11, 2010

    no easy way, very messy job indeed

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
djicenova
  • 319 Answers

SOURCE: need to replace transmission line to the cooler on a GMC Sierra

Its fairly easy, you dont have to replace the fittings at the cooler. if they are leaking up at the cooler, it needs to be replaced, but if not, its just simple line to line, not too long of a process

please rate well! hope this gives you the info you needed!

Posted on Mar 01, 2009

Ad
Molson02536
  • 3854 Answers

SOURCE: oil cooler lines replacement how hard and how long

It's harder then it seams, you have to disconnect the engine mount on the drivers side to get enough room to remove and replace the old oil lines. Other then the engine needing to be raised a bit, it's simple. Good luck and hope this helps, it takes about 3 to 4 hour to do this job and don't for get to use lock tight and keep everything clean. 

Posted on Jul 16, 2009

  • 7353 Answers

SOURCE: how do you get the oil cooler line loose at the

there should be 1 nut and stud holding the lines to the housing. I would suggest replacing the upper o-ring for the oil filter adapter at the same time. The oil cooler hoses are also prone to leak, if so, you want to replace evreything while you are there.

Posted on Sep 21, 2009

  • 10 Answers

SOURCE: oil cooler line replacement on a 1998 Suburban

remove oil filter assembly press plastic tabs pull line out should replace tabs and o ring on assembly to block

Posted on Nov 26, 2009

Molson02536
  • 3854 Answers

SOURCE: oil cooler lines leaking

Inspect where the oil is leaking from the oil cooler line, it's common for the oil to leak from the remote oil cooler line adapter bolt on the engine block. You can remove the two bolts one at a time and place a oil drain plug washer with some RTV silicon to ensure that it will not leak.

The other common place for the oil line to leak is from where the rubber lines mate to the aluminum line from the remote oil filter line adapter. This is also a simple fix but you're going to need a drumlin tool cut off the old compression clamp that was press fit. Cut off the old compression fitting ring, use cation that you only cut off the ring and replace it with a new compression clamp. Make sure you use compression clamps and not a hose clamp.

This is the best way to fix the oil leak from the adapter line to the rubber hose line, to replace the whole line with the new adapter is expensive and i believe your have to disconnect the engine mount to raise the engine to clear enough room to install the new line along the frame.

Good luck and don't use any engine oil stop leak, it will damage your oil pressure relieve valve and that's one extra thing you don't need to replace.

Posted on Feb 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3.9l. How can I replace engine oil cooler lines?


This should be a straight forward swap to a new line. Loosen fittings, remove clips, unscrew retainer on block and drain oil from old line to avoid messy spills and replace.

Video Chevy Astro Van Oil Cooler Lines Replacement - Should be a very similar procedure for your Impala.

625 665 How to replace an oil cooler line


Find part information here:
Dorman Hose Engine Oil Cooler 625 665 ReadReviews onDorman

May 15, 2016 | 2006 Chevrolet Impala

1 Answer

SE. How do I remove transmission oil cooler line?


How To Install Replace Transmission Cooler Lines 2001-06 ...

? 5:45
https://www.youtube.com/watch?v=SFEXmxxBMK8
Oct 31, 2013 - Uploaded by 1A Auto Parts
How To Install Replace Transmission Cooler Lines 2001-06 ... In this video, 1A Auto shows you how to remove, replace and install leaking or broken Transmission Cooler ... How To Install ReplaceDo a Front Brake Job 2001-06 Chrysler ... 2003 Dodge Ram 3500 trans cooler replacement how to 11-24-12 ...

Search DODGE MAGNUM Cooling > Transmission Oil ...

www.factorychryslerparts.com > ... > Transmission Oil Cooler, and Lines
DODGE MAGNUM Cooling > Transmission Oil Cooler, and Lines. ... Please let us know what we can do to achieve this goal. ... Our inventory covers the following years of MAGNUM: 2005, 2006, 2007, 2008, ... Click X to remove the keyword.

Leaking Transmission Cooler Line Replacment Recommendations ...

www.dodgeintrepid.net > ... > General Discussion (First Generation)

Dec 12, 2015 | 2006 Dodge Magnum

1 Answer

How to replace oil; cooler on this year


  • Service and Repair
Oil Cooler Replacement

Removal Procedure

  1. Raise and support the vehicle. Refer to Vehicle Lifting.
  2. Drain the engine oil and remove the oil filter housing.
89116492

  1. Loosen the oil cooler outlet (1) and the inlet (2) lines from the engine block.
  2. Lower the vehicle.
  3. Remove the intake plenum.
  4. Remove the intake manifold.
89116493

  1. Disconnect the following electrical connectors from the water crossover:
    • The engine coolant temperature sender (2)
    • The engine coolant temperature sensor (4)
84936658

  1. Remove the water crossover bolts (1).
  2. Remove the water crossover upper and lower seals (2).
84942881

  1. Loosen the upper heat shield bolts on the left side of the exhaust manifold.
89116496

  1. Remove the oil cooler outlet line from the engine oil cooler.
  2. Remove the oil cooler inlet line from the engine oil cooler.
84942883

  1. Note the positioning of the 4 seals.
84972057

  1. Position the oil feed and return,lines out of the way and secure with mechanic wire.
  2. Remove the engine oil cooler, inlet and outlet nuts (1).
  3. Remove the engine oil cooler cover bolts (2).
84942883

  1. Remove the engine oil cooler cover.
  2. Remove the engine oil cooler.
  3. Clean all sealing surfaces.
Installation Procedure
84972056

  1. Install the engine oil cooler.
  2. Apply a 2 mm (0.08 inch) bead of RTV silicone sealant, GM P/N 12346240, in the groove around the engine oil cooler cover.
  3. Install the engine oil cooler cover.
Notice: Refer to Fastener Notice in Service Precautions.
84972057

  1. Install the engine oil cooler cover bolts (2). Tighten the engine oil cooler cover bolts to 30 Nm (22 ft. lbs.).
  2. Install the engine oil cooler inlet and outlet nuts (1). Tighten the engine oil cooler inlet and outlet nuts to 20 Nm (15 ft. lbs.).
  3. Reposition the oil feed and return lines.
84942883

  1. Install the oil cooler outlet and install the oil cooler inlet lines to the engine oil cooler. Use 4 new seals.
Tighten the oil feed and return lines to 30 Nm (22 ft. lbs.).
84936658

  1. Install the water crossover:
    • Position the crossover.
    • Install the upper and lower seals (2).
    • Install the water crossover bolts (1). Tighten
Tighten the water crossover bolts to 30 Nm (22 ft. lbs.).
  1. Connect the electrical connectors at the following locations:
    • The engine coolant temperature sensor (4)
    • The engine coolant temperature sender (2)
  1. Install the intake manifold.
  2. Install the intake plenum.
  3. Raise the vehicle.
89116492

  1. Install the oil cooler outlet (1) line to the engine block. Tighten the oil cooler outlet (1) line to 30 Nm (22 ft. lbs.).
  2. Install the oil cooler inlet (2) line to the engine block. Tighten the oil cooler inlet (2) line to 30 Nm (22 ft. lbs.).
  3. Install the oil filter housing to the engine block. Tighten the oil filter housing to 45 Nm (33 ft. lbs.).
  4. Lower the vehicle.

Dec 22, 2014 | 2001 Cadillac Catera

2 Answers

Identification of transmission oil cooler lines. Inlet v Return


may need to go to a transmission shop and let them tell you which is which..only other way is to open a line and see which way the fluid runs..

Feb 08, 2014 | 1998 Chevrolet Lumina

1 Answer

High pressure oil cooler lines


No easy way. It is a pain job. Correct size wrenches most important. No adjustables. Fan and shroud and underpan removed helps. Most of the time you need to remove the front motor motor mount to get a good purchase on the front housing fitting. Most critical is to use two wrenches on the cooler, making sure that the fittings that goes into the cooler do not move , leaks will occur and if you try tighten the fitting, you will crack the housing boss and ruin the cooler.

Removing the front mount requires holding the engine up with a holder of hoist. When installing, do not overtighten at the oil cooler.

Apr 18, 2012 | 1986 Mazda RX-7

2 Answers

Oil hose leak 97 4x4 Blazer


Oil cooler lines that lead to your radiator or to a cooler mounted in front of radiator.The hoses are quick couplers with o-rings so there is no way to tighten. I don't know why they would leek so often but they usualy go bad where the rubber line gets crimped to the steel line.Not sure if you can get a different oil filter block without the oil cooler line hook ups.This way you can eliminate the cooler lines,or remove the quick couplers at both ends of where your cooler lines hook up and just run hydraulic hoses in place of your coller lines.Where i live you can get hydraulic hoses made at hundreds of places but may not be so redily avalible where you are.

Jan 16, 2010 | 1997 Chevrolet Blazer

1 Answer

How to replace oil cooler f250


drain oil from drain plug, take off oil line inlet from cooler, have bucket ready for oil. take off oil line outlet and undo retaining bolts, take off cooler.
put on new oil cooler, connect oil lines. might as well replace oil filter. add new oil.
done

May 11, 2009 | 1992 Daihatsu Charade

1 Answer

Need to replace transmission line to the cooler on a GMC Sierra


Its fairly easy, you dont have to replace the fittings at the cooler. if they are leaking up at the cooler, it needs to be replaced, but if not, its just simple line to line, not too long of a process

please rate well! hope this gives you the info you needed!

Feb 28, 2009 | 1998 GMC Sierra

2 Answers

Oil leak


common oil leak on those vehicles is the "quick connects" where the oil lines go into the oil cooler (what i believe you are calling the "doble") replace the o-rings on the quick connects for the lines

Oct 05, 2008 | 1999 GMC Suburban

Not finding what you are looking for?
1993 Chevrolet K1500 Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6910 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...