Question about 1986 Dodge Ram 50

1 Answer

Need timing for a 1986 dodge ram 50 2.0l

Need timing

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

Take it in get it done or get yourself a timing gun and so it yourself.

Posted on Sep 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I put a new battery in my 1986 Dodge ram 50 that has been sitting for a long time. I have no power, is there a master fuse somewhere I need to check?


Check ur balast resistor on the coil located next to the batery if this is bad it can cause either no electricity or too much electricity going through ur vehicle could blow fuses all the time or not give any power to them if u have a ohm meter. Disconnect wires going to balast and read across terminals if it reads more the 1.7 ohms the replace it u should not see k ohms or M ohms just 1.7 or lower. Hope this helps

May 24, 2012 | 1986 Dodge Ram 50

1 Answer

Rebuilded a 2.0 1986 inline 4 cyclinder dodge ram 50. Need to reset the cam shaft to the crankshaft for the timing. The cam shaft timing mark is 90 degrees and facing left of the crank shaft. What is the...


My sincere apologies for the severly delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, however I am answering it in case you still do.


Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com


http://www.2carpros.com/car_repair_information/year/1986/make/dodge/model/ram_50/1986_dodge_ram_50_timing_belt_diagram_marks.htm

Mar 03, 2010 | 1986 Dodge Ram 50

1 Answer

My truck is a 1986 dodge ram with power windows that wont work


YOU NEED TO TAKE THE INSIDE DOORPANELS OFF AND CHECK WINDOW WIRINGS AND CONECTIONS, FOR MOISTER AND BREAKS IN WIRES.

Oct 19, 2009 | 1986 Dodge Pickup 4WD

2 Answers

Where is the EGR valve on 1986 Dodge Ram D50 pickup 2.0cc 4 cyl


if there pipes or tubes on top of your exhaust manifold that is where your EGR valve should be. if you want diagrams or text to help fix this problem i suggest the book from Chilton. they tend to explain thing pretty well.

Oct 01, 2009 | 1986 Dodge Ram 50

1 Answer

I need the timing marks to set the crankshaft to top dead center for a timing belt replacement. I just need a diagram to show me where the timing marks are located, where should the camshaft pulley mark be...


1986 Dodge Truck RAM 50 4WD 2.6L 2BL 4cyl

Fig. Timing belt and components-2.0L engine
9f07c9a.jpg


Fig. Location and correct alignment of timing marks for the timing belt (camshaft)
6f4c9d6.jpg


Fig. Timing marks-2.3L diesel engine
40625e5.jpg


Fig. Timing marks-2.4L engine
124bdbc.jpg


More details, autozone.com (free register). Good luck.

Sep 29, 2009 | 1986 Dodge Ram 50

1 Answer

Mitsubishi Dodge ram starting problem


Try changing the starter relay switch.

Jun 08, 2009 | 1986 Dodge Ram 50

1 Answer

1986 DODGE RAM 1500


it sounds like a timeing issue but in the distributor itself. check your weights inside your distributor they could possibly be stuck

Apr 29, 2009 | 1986 Dodge Ram Wagon

1 Answer

Put new oilpump and hadto remove timeing belt and gears. i need t


For the 1986 Dodge Ram 50 2.0L AND 2.6L 4-Cylinders:

Firing Order:
1-3-4-2

Cylinders:
(back)
...4
...3
...2
...1
(front)

Distributor:
.(back)
3.......4
1.......2
.(front)

For the Timing Marks: Click on the following Link. It has the Position of the Cranshaft and Camshaft and their respective marks.

http://www.2carpros.com/car_repair_information/year/1986/make/dodge/model/ram_50/1986_dodge_ram_50_timing_belt_diagram_marks.htm

Jan 02, 2009 | 1986 Dodge Ram 50

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...