Question about 2000 Volkswagen Jetta TDI

1 Answer

Wiper motor running but wipers not? - 2000 Volkswagen Jetta TDI

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 299 Answers

Probably a bad link see if you can find it by moving the driver wiper by hand if both move then the link to the motor is bad if only one moves either loose arm nuts or wiper to wiper link is bad

Posted on Sep 30, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jimboz4
  • 305 Answers

SOURCE: Wiper arm behind wiper motor disconnected from motor

its a wiper control arm nylon bush

Posted on Jul 23, 2009

  • 8 Answers

SOURCE: windshield wipers

According to AllData, you don't have to remove the motor to install a new switch. Subsequently, AllData doesn't give direction on wiper arm or motor removal. Here are the only diagrams they give for switch replacement.

41917584 41917585

Posted on Nov 26, 2008

motor1258
  • 6674 Answers

SOURCE: windshield wipers quit working

Probably stripped at the spline where pivots. Try getting arms off at the pivot point, cleaning, re-attach & tighten if there is a nut holding them to pivot.

Posted on Dec 19, 2008

  • 169 Answers

SOURCE: replaced wiper motor but still won't work buzzes

can you move the linkage when you pulled the motor?

Posted on Aug 30, 2009

SQUIRESXX
  • 486 Answers

SOURCE: Wiper motor running but wipers not moving

you proberly need to access the motor , normaly under the front screen beneth hood, but could be visable from under dash, sounds like the link from the wiper mech has detached from the wiper motor drive, simple to fix once you gain access, normally its just a nut/pin that has come off unless arm broke which would cause a lot of noise

Posted on Dec 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1996 saturn wiper motor working but wipers don't move


Hello, It sounds like your wiper motor is running but you have a wiper arm rod disconnected. Usually under a cowling and leaf screen near the wiper motor.

Aug 28, 2014 | Cars & Trucks

1 Answer

Wipers would not park, customer forced down wiper arm and broke off arm. Now no electric to wipers.


Before 1995 Ford interval wiper systems mainly consisted of a switch, the motor and the interval governor (also called the wiper control module or 'WCM'). The basic wiper systems just parked the wipers at the end of their travel at the base of the windshield and involved just one park switch.

The more complex systems not only stopped the wipers at the base of the windshield, but would actually recess them below the windshield to park them. This involved using two park switches to turn the wiper motor in a reverse direction. These were installed on the Crown Victoria, Grand Marquis, Town Car, Taurus and Sable.

The wiper switch (named 'Multi-Function Switch' on most models) had a common return or ground circuit and two input or signal circuits to the WCM. Basically, the switch was two modified potentiometers that varied the resistance to ground for the two signal circuits. When the wiper switch was placed in the low or high position, the WCM looked at only one of the circuits- the 'mode input' -and controlled the wiper motor accordingly. If the wiper switch was placed in any of the interval positions, the mode input told the WCM that the switch was in an interval position. The WCM then looked at the second input - the 'delay input' - and used it to determine the amount of delay between wipes.

1) To run the wipers on low or high speed, the WCM provided constant power to the wiper motor on the proper circuit to provide the requested speed. Dual park switch motors
1.1 The first park switch operated basically in the same way as the single switch systems.
1.2 The second park switch worked in the opposite manner- when the wipers were off the park position, the second switch provided a ground for the wiper motor. Power and ground were now provided by the park switches.
1.3 When the wipers needed to park, the polarity of the switches changed, and thus provided reversed voltage to drive the motor in the opposite direction.

2) To run the interval wipers, the WCM applied voltage to the wiper motor only momentarily to get the wipers off the parked position.
3) The electro-mechanical park switch made a circuit between the power feed in and the output to the WCM. Power was provided from the park switch through the WCM and back to the wiper motor.
4) When the wipers reached the park position, the park switch made a circuit between the ground and the output to the WCM, and the motor stopped running. The wiper motor and the wiper switch have remained much the same as the single park switch motors of the past.

The main difference is that the switch has become an input to the GEM instead of the WCM.
1) When the wiper switch is placed in the low or high position, the Run-Park relay is grounded by the GEM to provide constant voltage to the High-Low relay, which then provides voltage to the proper circuit of the wiper motor.
2) High-Low relay is in the low speed position unless grounded by the GEM.
3) The park switch not only feeds the Run-Park relay but is now also an input to the GEM. This tells the GEM when the wipers are in the parked position so it can de-energize the Run-Park relay.
4) When any of the interval positions are selected, the Run-Park relay is momentarily grounded to get the wipers off the parked position
5) The park switch then provides voltage to the other set of contacts in the Run-Park relay.
6) When the GEM de-energizes the Run- Park relay, voltage is still provided from the park switch to the High-Low relay and the wipers complete the stroke.

Click over diagrams for zoom:

zjlimited_175.gif


zjlimited_176.gif


Hope this helps.

Feb 08, 2011 | 1993 Mercury Grand Marquis

2 Answers

Vw golf mk3 wipers not working,fuse ok. sometimes work if blades assisted manually


WIPER ARM LINKAGE COULD BE BINDING.REMOVE WIPER ARM TO SEE IF WIPER MOTOR OPERATE SLOWLY.IF YES CHECK TO MAKE SURE WIPER MOTOR GETTING GOOD GROUND CONNECTIONS BY CHECKING MOVING WIRES .IF WIPER MOTOR SPEEDS UP YOU HAVE GROUND WIRE PROBLEM. IF WIPER MOTOR REMAIN SLOW GROUND WIRES CHECK OUT OKAY.REPLACE WIPER MOTOR.IF WIPER MOTOR RUN FAST NORMAL SPEED AFTER DISCONNECTING WIPER ARM.WIPER ARM LINKAGES IS BINDING OR NEED SOME LUBRICATION TRY WD40 SEE WHAT HAPPENS.LUBRICATION DONT HELP WIPER LINKAGE COULD BE DAMAGED.

Nov 18, 2010 | 2000 Volkswagen Golf

3 Answers

Pontiac g6 2006 wipers stopped movement while driving. what could this be from? I already checked fuses. i hear the motor running making noise.


either linkage broke/ jammed or motor is stuck -makin noise but not movin open hood and with wiper on feel motor- its on firewall-for movement if moving turn off motor now try to move wipers if move freely than they are broken off or have disconnected from the motor need to remove the cowl to access the wipers linkages

Mar 13, 2010 | 2006 Pontiac G6

1 Answer

Snow was on windshield. i mistakenly turned on wipers before clearing snow. The wipers started to go up and stopped. Now the wipers won't do anything. The part that has the spring will rotate by hand and...


Does the wiper motor run? If you can hear the wiper motor run, the wipers arms may have disconnected from the wiper motor,you will have to remove the wiper arms,and the plastic cover to access the wiper motor,and check for damaged parts.If your wiper motor does nothing at all, you probably blew a fuse do to the resistance on the arms,refer to your owners guide for fuse panel, and fuse locations. hope this helps

Feb 14, 2010 | 2001 Pontiac Grand Prix

1 Answer

2000 taurus hear motor but arms dont move. i can


it sounds like the wiper transmission has broken/slipped off of the wiper motor. Remove wiper motor and check wiper transmission.

Dec 26, 2009 | 2000 Ford Taurus

1 Answer

The windshield wipers work sometines but don't work most of the time


check wiper motor ground wire.make sure its tight not corroded.check wiper motor for binding or remove wiper motor hot wire to see if run with out stopping.if it run with out stopping its has a faulty switch or binding.spray pivots and linkages with WD40 to help lubricate them.if wiper motor dont continue running or stop while hot wiring it.replace wiper motor.

Jul 10, 2009 | 1997 Dodge Caravan

1 Answer

Need to get a programmer dont know where its at


  • Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF
  • Damaged turn signal and windshield wiper switch .
  • Damaged windshield wiper motor .
  • Damaged windshield wiper control module.
7fd52e7.gif
efd7dbe.gif
Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
Windshield Wiper System The windshield wiper system consists of :
  • Windshield wiper motor (17508) (F-type).
  • Washer system.
  • Windshield wiper control module.
  • Turn signal and windshield wiper switch (13K359).
The windshield wiper control module is:
  • Located at the instrument panel fuse panel.
The windshield wiper motor is:
  • Attached to the cowl top extension (021A36) .
  • Connected to windshield wiper mounting arm and pivot shaft (17566) .
The turn signal and windshield wiper switch features a:
  • Rotary wiper switch.
  • Push type washer actuator.
OFF/Low/High Speed
  • Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
  • The windshield wiper motor has a brush rigging that permits selection of low or high speed.
  • When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
  • When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
  • In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
  • When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
  • When the park switch contacts open, the windshield wiper motor stops in the park position.
Interval
When the turn signal and windshield wiper switch is in the interval position:
  • The wipers make single wipes separated by pauses.
  • The rotary switch is on the end of turn signal and windshield wiper switch .
  • The length of the pause can be set from approximately 1 to 17 seconds.
  • Length of pause decreases as the rotary switch is rotated away from off.
  • Length of pause increases as the rotary switch is rotated toward off.
While in the interval wiper mode:
  • It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.

May 27, 2009 | 1994 Ford Mustang

2 Answers

Rear wiper stopped working


my 2004 expedition had same problem, if you take apart the shaft that goes thru the glass it will be full of dirt, clean ,lubricate and reinstall, you may have to replace the O-ring on the shaft. a 20 minute job, very easy fix

Feb 25, 2009 | 2004 Ford Expedition

2 Answers

Timing Venture wipers


disconnect the wiper transmission from the motor, then run the motor and turn the motor off with the wiper switch, this will park the motor, re-attach the wiper trans linkage so the wipers are parked/down

Dec 05, 2008 | 2000 Chevrolet Venture

Not finding what you are looking for?
2000 Volkswagen Jetta TDI Logo

Related Topics:

252 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...