Question about 1994 Mercedes-Benz C-Class

1 Answer

I have a 1997 E 320 benz and need to find a diagram of the engine to replace the crankshaft sensor- where can I find one?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 203 Answers

You do not need a manual. On the back of the bell housing(engine side not trans. side) you will find a plastic cover on the top driver's side. remove that plastic cover(they are often times missing) the crank sensor is under the cover and is retained by a 5mm. allen bolt. Often times they are just loose and that creates a bad ground.

Posted on Sep 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor located in the 1990 Chevrolet Corsica 4 cylinder 2.2 liter engine?


Follow this link to a diagram that will show you where it's located. Hope this helps.

Jul 11, 2016 | Chevrolet Cars & Trucks

1 Answer

I parked mercedece benz for an hour when i tryed to start it cant start it is crancking only but not starting


We see a lot of problems with Mercedes-Benz crankshaft sensors failing on hot engines. If the car starts after it cools, you likely have a bad sensor.

Feb 15, 2015 | Mercedes-Benz Cars & Trucks

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

3 Answers

Hi there, Hope you can help... According to Mercedez service centre after their diagnostic, I need to have crankshaft sensor and camshaft sensor replaced. Question: How difficult would it be for...


both sensors involve quite a bit of work to get to, the sensors are (in themselves) easy to replace!
CKP(crankshaft position sensor is around $55 at autozone where i live.
I cant seem to find the cam position sensor! call your local parts store. they could help with pricing
the CKP itself only requires 1 bolt and one wiring connector.
Good luck

Jan 21, 2011 | 2002 Mercedes-Benz C-Class

1 Answer

Cannot find the crank shift sensor location


M112 And M113 Engines
  1. Before servicing the vehicle, refer to the precautions.

  2. Remove air filter housing.

  3. Remove hot film mass air flow sensor.

  4. Remove air duct housing.

  5. Release and disconnect electrical connector at crankshaft Hall sensor.

  6. Remove bolt.

  7. Pull crankshaft Hall sensor out of crankcase.
    22205_mbca_g0045.gif

    CKP sensor location

To install:

  1. Installation is the reverse of removal.

  2. Tighten crankshaft Hall sensor to crankcase bolt to 6 ft. lbs. (8 Nm).

  3. Carry out first initialization and then sensor rotor adaptation using Star Diagnosis tool.

Oct 22, 2010 | 2002 Mercedes-Benz C-Class

1 Answer

Serpatine belt mercadise c350 diagram


Serpentine belt routing diagram for Mercedes C 350:
272 HP / 6000 rpm - Engine code: 272.960


cebd93c.png
CS = Crankshaft
G = Guide pulley
Gen = Alternator
T = Tensioner
AC = Air Conditioning
PAS = Power Assisted Steering
WP = Water Pump


Please rate my response. Thanks!

May 22, 2010 | 2008 Mercedes-Benz Mercedes Benz C Class

1 Answer

Replacing 2004 cavalier crank sensor, i can't locate the best way to replace it. need a diagram or where i can find it.


The crankshaft position sensor should be located on a small metal bracket very close to the harmonic balancer which is attached to the end of the crankshaft. If you are having trouble locating the harmonic balancer, it is the lowest pulley on the passenger side of the engine, in the center line of the engine.

Apr 10, 2009 | 2004 Chevrolet Cavalier

1 Answer

Crannkshaft senser


Hello , my name is JShreader. Thank you for choosing fixya.com.

There are 2 Crankshaft Position Sensors on this Engine. The 7X Crankshaft Position Sensor, a Magnetic Sensor, is bolted to the lower right side of the Engine Block.
aad05e9.jpg
The 24X Crankshaft Position Sensor, secured in an aluminum mounting bracket and bolted to the front left side of the Engine Timing Chain Cover, is partially behind the Crankshaft.
79e0c8d.jpg
I hope this helps you. If you have any more questions or need any more diagrams, please don't hesitate to ask...Thanks again, JShreader!

Mar 18, 2009 | 1997 Chevrolet Venture

Not finding what you are looking for?
1994 Mercedes-Benz C-Class Logo

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...