Question about 1995 Honda Passport

1 Answer

Replacing brake light bulbs, have removed the light fixture but how do you get to the bulbs themselves?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Push the bulb in nd twist counter clockwise and the bulb should come right out.

Posted on Oct 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace brake light bulb on 2005 mazda bounty


Gain access to the light fixture, remove the bulb holder, remove the burned out bulb and replace with new, test, then re-install the bulb holder and re-install the fixture.

Aug 30, 2014 | Cars & Trucks

1 Answer

Brake light and tail light out on same side. Replaced bulb in brake light but still neither still works.


Look at the wiring harness that runs to your tail light fixture. make sure that the harness connections have not loosened. check harness casing and bulb iixtures for breaks or corrosion... sounds like you have a short going on. with the light switch on, try wiggling the wiring where it goes into the fixture. if the light flickers at all while doing this you have a short going on in the fixture and it may need to be replaced.

Feb 28, 2013 | 1996 Dodge Stratus

1 Answer

Need to change rear brake light bulb on a 2000_L sedan. Owners manual addresses only the turn signal bulb change proceedure. The brake light fixture is flat not round.


there is an access cover in the trunk.Open that and just pull the bulb fixture out replace the bulb and place back in the hole.

Apr 07, 2012 | Saturn Cars & Trucks

2 Answers

Tail light bulb replacement on 2010 dodge challenger


there should be a fixture in the boot/trunk that holds the lights,that clips into a panel, find the clips that hold it in and release the lights fixture then you can change the bulb, clip fixture back in

Oct 08, 2011 | 2010 Dodge Challenger

1 Answer

I can't figure out how to get my 2003 Tundra taillight assembly off . I have removed the two bolts inside the tailgate area but it is still attached to the fender on the other side of the assembly . I have...


Unscrew the screws that are securing the brake light cover to the body of the Tundra. Pull the brake light cover off the body of the Tundra. Place the screws in the brake light cover and set it on the bed of the truck. Pull the burned-out light bulb out of the light fixture and discard it. Insert the new brake light bulb into the light fixture. Pump the Tundra's brakes to make sure the new bulb is working correctly. Replace the brake light cover on the body of the Tundra and replace the screws.

Sep 09, 2010 | 2003 Toyota Tundra

1 Answer

Brake light went out


In the trunk, pull back carpeting. remove 3 7/16 nuts from fixture. pull fixture out, twist bulb socket, replace bulb.

Apr 10, 2010 | 1999 Ford Crown Victoria

1 Answer

HOW DO I REPLACE CENTER BRAKE LIGHT BULB


this is not a bulb u must replace the entire LED fixture, to do this remove the inside trim at rear around rear hatch opening, then you will need to drop the headliner down to access the retainers that hold the third brake fixture in, very easy job.

Jul 09, 2009 | 1996 Ford Explorer

1 Answer

How to change my rear brake light bulb


Okay you need to lift your trunk remove any carpeting remove hidden screws to undo light fixture be careful not to drop the case once case is in your hand remove the appropriate bulb that needs replacing after wards reinstall light housing/casing and screws good luck with this. Please Rate Me. And for further assistance you can always ask me.

Apr 25, 2009 | Toyota Avalon Cars & Trucks

2 Answers

Replacing a brake light Tercel 1999


1999 Tercel rear light bulb replacement. Snap off 2 black caps to pull back carpet. Remove 2 screws on outside of trunk at the edge of trunk lid. The light fixture will loosen up. Sqeeze the tongs on the square white plastic plug on the inside and push plug through hole. You may have to give the light fixture a tug. Turn bulb holder and pull it out. Pull out bulb and put in new one.

Apr 02, 2009 | 1997 Toyota Tercel

2 Answers

PT Cruiser Brake Light


The bulb in the rear light has burned out and to replace it follow these instructions: 1) go to your owner's manual to find out the part number. You can find and purchase the replacement bulb at Target, any auto parts store and even at Walmart for under $4.00; 2) pop open the trunk door; 3) get a phillips screw driver and unscrew the 2 screws holding the rear brake light fixture to your car body; 4) as soon as you turn over the fixture you'll see where to pull out the burned out bulb and replace it with the new one(s). Good luck!

Jul 14, 2008 | 2006 Chrysler PT Cruiser

Not finding what you are looking for?
1995 Honda Passport Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...