Question about 2004 Saab 9-3

2 Answers

How do i remove the glove box to access the blower motor? Thanks.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

If you want to lubricate the blower motor you can try this solution
http://www.saabnet.ru/forum/topic1924-remont-ventilyatora-pechki-na-saab930307g-i-zamena-salonnogo-filtra.html
But i dont know how to accessit from the glove box.

Posted on Oct 05, 2009

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 35 Answers

I would jsut remove the lower black plastic under neath the glove box to access the blower motor.. its most likly not the motor but the resister on the bottom on the motor..
ELite auto carries used saabs parts

Posted on Oct 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 olds cutlass blower motor resistor


remove glove box to get better access to the blower motor. resistor is located beside the blower fan motor. with glove box removed, then you will not have to stand on your head doing the job, good-day!

Jan 29, 2012 | 1999 Oldsmobile Cutlass

1 Answer

Where is the blower motor located on a 97 rodeo


Hi, the blower motor is located behind the glove box or compartment.
  • Remove floor distribution ducts and glove box, as necessary to gain access to motor.
  • Disconnect electrical connector from blower motor.
  • Remove screws securing motor mounting plate to housing, then the motor assembly, taking care not to damage seal.
  • Remove retaining ring securing impeller, then the impeller.
  • Reverse procedure to install

May 27, 2011 | 1997 Isuzu Rodeo

2 Answers

Where is the heater fan located in a 2000 chevy impala?


Here's a great video too that will show you where it's located and how to replace it.">

Feb 14, 2011 | 2000 Chevrolet Impala

1 Answer

Heater only run on high speed


Hello Sanda.

The blower speed system on your car goes through a resistor to give various speeds.
The reason it still works on high is that when set on high it doesn't go through that resistor.

It gets direct battery voltage.
The resistor is not too expensive and easy to replace.

To replace;
  1. Open the glove box.
  2. Flex both sides of the glove box bin inward near the top far enough for the rubber glove box stop bumpers to clear the sides of the glove box opening, then roll the glove box downward.
kiltylake_143.gif
  1. Reach through the glove box opening to access and disconnect the instrument panel wire harness connector for the blower motor resistor from the resistor connector receptacle.
  2. Reach through the glove box opening to access and disconnect the blower motor pigtail wire connector from the resistor connector receptacle.
  3. Remove the two screws that secure the blower motor resistor to the evaporator housing.
  4. Remove the blower motor resistor from the evaporator housing.
There you are. Thank you for using FixYa.

KL

Jan 14, 2011 | 2001 Chrysler Town & Country

1 Answer

How to replace main heater fan


Blower Motor REMOVAL & INSTALLATION Front Fig. 1: Front heater blower motor assembly 89696g02.gif
Remove the glove box to access the front blower motor, which is on the firewall 89696p02.jpg
The blower motor is retained by four bolts (arrows) 89696p03.jpg
The blower motor vent tube helps to cool the blower motor for efficient operation 89696p04.jpg
Push up on the clip to remove the blower motor connector 89696p05.jpg
A ratchet with extensions makes removal of the retaining screws easier 89696p06.jpg
Lift the blower motor over the control cable . . . 89696p07.jpg
. . . and remove it from the vehicle 89696p08.jpg
  1. Disconnect the negative battery cable.
  2. Open the glove box door. Gently squeeze the retainers at the rear of the box inward and allow the box to swing downward. NOTE: If additional access is required, unfasten the glove box hinge retainers and remove the assembly.
  3. Label and disconnect the electrical harness from the blower motor.
  4. Remove the blower motor housing tube and/or blower motor cover.
  5. Remove the blower motor retaining screws.
  6. Remove the blower motor from the A/C evaporator. To install:
  7. Install the blower motor in the A/C evaporator and tighten the retaining screws securely.
  8. Install the blower motor housing tube and/or blower motor cover.
  9. Connect the electrical harness to the blower motor.
  10. Reinstall the glove box and close its door.
  11. Connect the negative battery cable.
Rear Fig. 2: Service cover push pin locations 89696g03.gif
  1. Disconnect the negative battery cable.
  2. Remove both rear passenger seats.
  3. Remove the three push pin retainers from the lower edge of the auxiliary heater and air conditioning service cover.
  4. Lift the service cover outward and upward to remove.
  5. Label and disconnect the electrical harness.
  6. Remove the blower motor housing tube.
  7. Loosen the three retaining screws and remove the blower motor. To install:
  8. Install the blower motor and tighten retaining screws securely.
  9. Install the blower motor housing tube.
  10. Connect the electrical harness.
  11. Position the service cover and install the three push pin retainers from the lower edge of the cover.
  12. Install both rear passenger seats.
  13. Connect the negative battery cable.
prev.gif next.gif

Dec 19, 2010 | 1998 Ford Windstar

1 Answer

How to access blower motor


The blower motor is located under your glove compartment on the passengers side.Remove the grey piece being held in by 3 plastic fasteners. Its the piece with the light for the passanger flour board in it. You will see the bottom of the blower motor. You will have to remove 3 screws, a wire plug and a rubber hose that just pulls off to get the motor out.The blower motor is located right behind the glove box. -------- Thanks.Helpmech.

Nov 15, 2010 | 1998 Pontiac Grand Prix

1 Answer

How to replace blower motor resistor


The blower motor resistor is located behind the glove compartment adjacent to the blower motor.There is a access door under the dash right below the glove box, There are few screws that you will have to remove to take the door out. The blower motor resistor, is to the left of the blower motor in the air conditioning case.The blower motor resistor is held by screws,remove the screws to take the resistor out. Keep updated with any further queries.Thanks.

Oct 12, 2010 | 1998 Chrysler Town & Country

1 Answer

How do I change a blower motor in a chrysler Town and country


Hello, to change the blower motor resistor follow this steps:
  1. Disconnect and isolate the battery negative cable.
  2. Open the glove box.
  3. Flex both sides of the glove box bin inward near the top far enough for the rubber glove box stop bumpers to clear the sides of the glove box opening, then roll the glove box downward.
  4. Reach through the glove box opening to access and disconnect the instrument panel wire harness connector for the blower motor resistor from the resistor connector receptacle.Blower motor Resistor
  5. Reach through the glove box opening to access and disconnect the blower motor pigtail wire connector from the resistor connector receptacle.
  6. Remove the two screws that secure the blower motor resistor to the evaporator housing.
  7. Remove the blower motor resistor from the evaporator housing.

Thanks

Aug 25, 2010 | 2006 Chrysler Town & Country

1 Answer

WHERE IS LOCATED BLOWER MOTOR IN DODGE GRAND


the blower motor is located in behind the glove box. lower the glove box door and look inside. to remove the blower motor you will have to remove the glove box door and the lower half or the instrument panel to gain access to the heating/air conditioning unit.

Apr 27, 2010 | 2005 Dodge Caravan

2 Answers

Replacing Blower Motor Resistor


  1. Disconnect and isolate the battery negative cable.
  2. Open the glove box.
  3. Flex both sides of the glove box bin inward near the top far enough for the rubber glove box stop bumpers to clear the sides of the glove box opening, then roll the glove box downward.
  4. Reach through the glove box opening to access and disconnect the instrument panel wire harness connector for the blower motor resistor from the resistor connector receptacle (Blower Motor Resistor).
  5. Reach through the glove box opening to access and disconnect the blower motor pigtail wire connector from the resistor connector receptacle.
  6. Remove the two screws that secure the blower motor resistor to the evaporator housing.
  7. Remove the blower motor resistor from the evaporator housing.80ac4e54.gif

Feb 04, 2009 | 2003 Chrysler Town & Country

Not finding what you are looking for?
2004 Saab 9-3 Logo

Related Topics:

979 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

rgbypoet

Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...