Question about 1999 Chevrolet Silverado 1500

Open Question

Who i change reverse switch on 1996 chevrolet silverado

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 17 Answers

SOURCE: Stop ligth switch

it on break petal arm half way up mark old one for ref

Posted on Jan 11, 2009

mcgyver468
  • 710 Answers

SOURCE: where is the fuel pump shutoff switch located on a 1996 chevy silverado 1500 located

Should be on the passenger side kickplate below the glovebox and to the right. You may have to remove the plastic panel to access it or look for a small hole in it and feel around for the button

Posted on Apr 23, 2009

  • 56 Answers

SOURCE: 02 Chevrolet Silverado z71 5.3 L wont go into reverse

Usually reverse is the first gear to go out in these transmissions (auto) probably a 4l60E model transmission Im guessing

Posted on Jan 03, 2010

  • 10 Answers

SOURCE: I have a 1996 Chevrolet 2500 2WD with the vortec

mine did the same thing i tried the fuse first and it didnt fix it and it was the relay but try the fuse first

Posted on Feb 11, 2010

  • 74 Answers

SOURCE: know how to change the oil pump in my 1997 chevrolet SILVERADO?

The oil pump is in the the oil pan so you will need a new oil pan gasket and some form a gasket as well to put the pan back on, because you will have to take it off, you will see the oil pump a soon as you take the pan off, it will have a tube connecting to the pick up screen and to the block, remove bolts from the block and remove oil pump. be prepared the primming rod will probably come out too. itll need to go back of course, make sure seated in correctly because the primming rod runs off the cam. make sure the surface area for the oil pump gasket is clean before reinstalling new oil pump same goes for oil pan. after everything back together refill oil. It is best to test the oil pump before starting for your engine. the best way to do this is to remove the distrubuter if it has one if it has electronic ignition it will have a cap where the distributer went remove that and you will see the top end of the primming rod, fit appropriate socket on the primming rod and use a battery gun to spin, look inside oil fill cap and make sure you see oil flow or oil pressure on your gage if equiped, CAREFULL!!!!!! make sure the socket on battery gun has no way of falling off, or you will have to remove oil pan again to retrieve it.
Another way to prime pump is to disable igniton main power like remove the coil wire, or main power wire for electronic igniton so you can turn the motor over with out it starting, once again turn it over until you know you have oil pressure with the gage or through oil fill cap. put ignition back together start the car and once again confirm oil pressure. If every thing looks good your done Good luck

Posted on Mar 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1996 Silverado does not do anything when trying to start. No clicking or anything. Battery ok. Jumpered clutch switch did not help.


Try hotwiring the solenoid on the starter. Suspect you have a bad solenoid. If hotwire works, problem is in wiring or ignition switch.

Aug 25, 2010 | 1996 Chevrolet Silverado 2500

1 Answer

No heat on 1996 Chevy Silverado 1500


reverse the heater hoses and drive it for a cpouple of days your heater core is plugged and by reverseing them you can back flush the heater core after 2-3 days reverse them again

Jan 18, 2010 | 1996 Chevrolet K1500

2 Answers

06 Silverado Reverse and dome lights don't work. All other


I have the same problem, not sure, but I think it is related to my headlight switch. My windshield leaks and the switch has water damage. Check at your trailer light harness to see if you have power there, it runs off a separate circuit/fuse.

Jan 17, 2010 | 2006 Chevrolet Silverado

1 Answer

1995 chevy silverado z71 no power to right tail light


check fuse.if good you got grounding problems or faulty turn signal switch.

May 09, 2009 | 1996 Chevrolet K1500

1 Answer

Where is the fuel pump shutoff switch located on a 1996 chevy silverado 1500 located


Should be on the passenger side kickplate below the glovebox and to the right. You may have to remove the plastic panel to access it or look for a small hole in it and feel around for the button

Apr 23, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

How do I change the door handles on 1996 chevy silverado?


take the door panel off from the inside. reach inside and undo the rod that locks and unlocks the door and 2 screws with a size no. 10 wretch and it should come right off.

Apr 14, 2009 | 1996 Chevrolet C1500

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...