Question about 2001 Ford F250 Super Duty Super Cab

Open Question

Can not get fuel pump out of tank - 2001 Ford F250 Super Duty Super Cab

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the steps to replace the fuel pump on a chevy trailblazer 2002


This is what it looks like and it is located in the gas tank:


c17hydro_197.gif
First, you'll need to use up as much fuel as possibly, if not, you'll have to drain the tank. Next:

  1. Drain the fuel tank.
  2. Support the fuel tank.
    1. Remove or disconnect the following:
    2. Negative battery cable
    • Filler neck from the tank
    • Shield from tank and tank straps
    • Fuel lines and vapor hose from pump
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
  • NOTE
    The fuel pump strainer must be in a horizontal position when the fuel sender is installed in the tank. When installing the sender assembly, make sure that the fuel pump strainer does not block full travel of the float arm.

    To install:

    1. Install or connect the following:
      • Fuel pump in tank with new seal around opening

      NOTE

      The fuel pump strainer must be in a horizontal position when the fuel sender is installed in the tank. When installing the sender assembly, make sure that the fuel pump strainer does not block full travel of the float arm.

      • Tank and connect fuel lines and vapor hose
      • Tank to the frame. Torque the fasteners to 33 ft. lbs. (45 Nm).
      • Shield
      • Fuel filler neck and clamp
      • Negative battery cable
    2. Refill the tank.
    3. Run the engine and check for leaks.
    // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 33; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

    Jul 08, 2011 | 2002 Chevrolet TrailBlazer

    1 Answer

    I need to replace the fuel pump on my 2001 Saturn L200 with a 2.2 L Engine. What is the best procedure?


    Fuel Pump REMOVAL & INSTALLATION 1.9L Engine To prevent excessive fuel spillage, whenever the tank is removed from the vehicle it should be no more than 1?2 full. Removal of the fuel pump module assembly requires the removal of the fuel tank.
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Properly relieve the fuel system pressure.
    3. Remove or disconnect the following:
      • Negative battery cable
      • Fuel feed and return lines from the filter/pressure regulator
      • Fuel pump vapor line from the fuel tank vent pipe
      • Fuel pump module retaining ring with service tool SA9156E. A 1?2 inch breaker bar will loosen the lockring
      NOTE: To prevent bending of the sending unit float arm, lift the pump module up slightly to disengage the orientation tabs in the tank. Rotate the module 90 degrees clockwise until the fuel lines are facing the 1 o'clock position.
      • Fuel pump module from the fuel tank until the bottom of the pump module is close to the fuel tank opening
      • Tilt the pump module approximately 45 degrees to the right hand side of the tank and lift the pump from the fuel tank
      • Fuel pump to tank seal and discard it
      To install:
    4. Install or connect the following:
      • Fuel pump module into the fuel tank by orientating the float to face the right side and tilting the module approximately 45 degrees
      • Fuel pump into the tank and rotate the assembly 90 degrees counterclockwise to align the module tabs with the slots in the tank
      NOTE: The fuel pump retaining ring cannot be properly installed if the flange locator tabs are not aligned with the slots in the fuel tank.
      • Retaining lockring with tool SA9156E
      • Vapor line to the fuel tank vent pipe
      • Fuel feed and return lines to the filter/pressure regulator
      • Fuel feed, return and EVAP canister purge line in the fuel tank retaining clip
      • Fuel tank
      • Negative battery cable
    5. Start the vehicle and check for leaks, repair if necessary.
    2.2L and 3.0L Engines
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Properly relieve the fuel system pressure.
    3. Remove or disconnect the following:
      • Negative battery cable
      • Fuel tank
      • Fuel lines from the fuel pump module cover
      • Fuel pump module retaining ring with a Sending Unit Wrench, J43827
      • Pull the retaining clip toward the float arm and lift up
      • Fuel pump straight up from the fuel tank
      • Fuel pump tank seal and discard the seal
      • Fuel feed line from the bottom of the fuel pump cover with Clamp Pliers J43914
      • Fuel pump electrical connector Fig. 1: Remove the fuel pump cover lockring-2.2L and 3.0L engines 9306zg57.gif
      To install:
    4. Install or connect the following:
      • Fuel pump feed line to the cover
      • Fuel pump electrical connector
      • Fuel pump to the new seal
      • Fuel pump cover lockring with tool J-43827
      • Fuel lines and wiring harness
      • Fuel tank
      • Negative battery cable
    5. Start the vehicle and check for leaks, repair if necessary.
    prev.gif next.gif

    Jan 29, 2011 | 2001 Saturn L-Series

    1 Answer

    Can fuel pump be put in without dropping the tank.


    Removal & Installation To Remove:
    1. Properly relieve the fuel system pressure.
    2. Drain the fuel tank through the filler pipe.
    3. Support the fuel tank.
    4. Remove or disconnect the following:
      • Negative battery cable
      • Filler neck
      • Shield and tank straps
      • Fuel lines and vapor hose from pump and tank
      • Electrical connection from fuel pump
      • Fuel tank
      • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
      • Fuel pump from the fuel lever sending device
    To Install:
    1. Install or connect the following:
      • Fuel pump in tank with new seal around opening
      • Tank and connect fuel lines and vapor hose
      • Tank to the frame
        1. Torque to: 33 ft. lbs. (45 Nm)
      • Shield
      • Fuel filler neck and clamp
      • Negative battery cable
    2. Refill the tank.
    3. Run the engine and check for leaks.
    View of the in-tank fuel pump assembly. 7924jg21.gif

    prev.gif next.gif

    Oct 09, 2010 | 1999 GMC Jimmy

    1 Answer

    Access panel for fuel pump


    There is none:

    Fuel Tank & Fuel Pump Module Assembly Removal & Installation To Remove:
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Shift the vehicle into NEUTRAL and position it on a hoist.
    3. Release the fuel pressure.
    4. Disconnect the negative battery cable.
    5. Remove the fuel tank filler cap.
    6. Drain as much fuel from the tank as possible.
    7. Using suitable hose pinching pliers, clamp the fuel tank filler hose. Clamp the fuel tank filler hose in the location shown ford-05-00-396.gif

    8. Disconnect the three quick connect couplings from the fuel tank tubes at the tank.
    9. Disconnect the fuel pump electrical connector.
    10. Disconnect the fuel filter inlet tube from the filter.
    11. Position a suitable lifting device under the fuel tank.
    12. Remove the two fuel tank support strap bolts.
    13. Lower the fuel tank to access the fuel pump module while swinging the fuel tank support straps away from the tank.
    14. Clean the area around the fuel pump mounting flange.
    15. Disconnect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
    16. Using the special tool, turn the fuel pump module retaining ring counterclockwise and remove it. CAUTION
      The fuel pump module must be handled carefully to avoid damage to the float arm, filter and convolute hoses.
    17. Turn the fuel pump module counterclockwise and the fuel pump module will release from the locking tabs. Remove the fuel pump module from the fuel tank.
    To Install:
    1. Install the fuel pump module in the fuel tank.
    2. Connect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
    3. Raise the tank into position and install the mounting strap bolts. Tighten the bolts to 26 ft-lbs (35 Nm).
    4. Connect the fuel lines and electrical connectors at the fuel tank.
    5. Lower the vehicle and refill the tank.
    6. Connect the negative battery cable.
    7. Turn the ignition key to the ON position to pressurize the fuel system.
    8. Visually inspect the fuel system for leaks.
    prev.gif next.gif

    Oct 05, 2010 | 2000 Ford Taurus

    1 Answer

    Instructions on how to remove fuel pump for 95 chevy blazer 4x4


    Removal & Installation
    To Remove:


    1. Properly relieve the fuel system pressure.
    2. Drain the fuel tank through the filler pipe.
    3. Support the fuel tank.
    4. Remove or disconnect the following:

      • Negative battery cable
      • Filler neck
      • Shield and tank straps
      • Fuel lines and vapor hose from pump and tank
      • Electrical connection from fuel pump
      • Fuel tank
      • Fuel pump/sending unit assembly by turning the locking ring (located on top
        of the fuel tank) counterclockwise using a spanner wrench
      • Fuel pump from the fuel lever sending device

    To Install:


    1. Install or connect the following:

      • Fuel pump in tank with new seal around opening
      • Tank and connect fuel lines and vapor hose
      • Tank to the frame

        1. Torque to: 33 ft. lbs. (45 Nm)

      • Shield
      • Fuel filler neck and clamp
      • Negative battery cable

    2. Refill the tank.
    3. Run the engine and check for leaks.






    View of the in-tank fuel pump assembly.
    7924jg21.gif




    prev.gif next.gif

    Sep 23, 2010 | Chevrolet Blazer Cars & Trucks

    3 Answers

    Needs fuel pump


    Removal & Installation To Remove:
    1. Properly relieve the fuel system pressure.
    2. Drain the fuel tank through the filler pipe.
    3. Support the fuel tank.
    4. Remove or disconnect the following:
      • Negative battery cable
      • Filler neck
      • Shield and tank straps
      • Fuel lines and vapor hose from pump and tank
      • Electrical connection from fuel pump
      • Fuel tank
      • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
      • Fuel pump from the fuel lever sending device
    To Install:
    1. Install or connect the following:
      • Fuel pump in tank with new seal around opening
      • Tank and connect fuel lines and vapor hose
      • Tank to the frame
        1. Torque to: 33 ft. lbs. (45 Nm)
      • Shield
      • Fuel filler neck and clamp
      • Negative battery cable
    2. Refill the tank.
    3. Run the engine and check for leaks.
    View of the in-tank fuel pump assembly. 7924jg21.gif

    prev.gif next.gif

    Sep 18, 2010 | 1997 Chevrolet Blazer

    2 Answers

    How do u get the fuel pump on


    Removal & Installation To Remove:
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Shift the vehicle into NEUTRAL and position it on a hoist.
    3. Release the fuel pressure.
    4. Disconnect the negative battery cable.
    5. Remove the fuel tank filler cap.
    6. Drain as much fuel from the tank as possible.
    7. Using suitable hose pinching pliers, clamp the fuel tank filler hose. Clamp the fuel tank filler hose in the location shown ford-05-00-396.gif

    8. Disconnect the three quick connect couplings from the fuel tank tubes at the tank.
    9. Disconnect the fuel pump electrical connector.
    10. Disconnect the fuel filter inlet tube from the filter.
    11. Position a suitable lifting device under the fuel tank.
    12. Remove the two fuel tank support strap bolts.
    13. Lower the fuel tank to access the fuel pump module while swinging the fuel tank support straps away from the tank.
    14. Clean the area around the fuel pump mounting flange.
    15. Disconnect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
    16. Using the special tool, turn the fuel pump module retaining ring counterclockwise and remove it. CAUTION
      The fuel pump module must be handled carefully to avoid damage to the float arm, filter and convolute hoses.
    17. Turn the fuel pump module counterclockwise and the fuel pump module will release from the locking tabs. Remove the fuel pump module from the fuel tank.
    To Install:
    1. Install the fuel pump module in the fuel tank.
    2. Connect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
    3. Raise the tank into position and install the mounting strap bolts. Tighten the bolts to 26 ft-lbs (35 Nm).
    4. Connect the fuel lines and electrical connectors at the fuel tank.
    5. Lower the vehicle and refill the tank.
    6. Connect the negative battery cable.
    7. Turn the ignition key to the ON position to pressurize the fuel system.
    8. Visually inspect the fuel system for leaks.
    prev.gif next.gif

    Aug 19, 2010 | 2001 Ford Taurus

    1 Answer

    How to put hi pressure fuel pump into the engine,it does not have any mark on the pump rotor?


    prev.gif next.gif Removal & Installation To Remove:
    1. Properly relieve the fuel system pressure.
    2. Drain the fuel tank through the filler pipe.
    3. Support the fuel tank.
    4. Remove or disconnect the following:
      • Negative battery cable
      • Filler neck
      • Shield and tank straps
      • Fuel lines and vapor hose from pump and tank
      • Electrical connection from fuel pump
      • Fuel tank
      • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
      • Fuel pump from the fuel lever sending device
    To Install:
    1. Install or connect the following:
      • Fuel pump in tank with new seal around opening
      • Tank and connect fuel lines and vapor hose
      • Tank to the frame
        1. Torque to: 33 ft. lbs. (45 Nm)
      • Shield
      • Fuel filler neck and clamp
      • Negative battery cable
    2. Refill the tank.
    3. Run the engine and check for leaks.
    View of the in-tank fuel pump assembly. 7924jg21.gif

    prev.gif next.gif

    Jul 15, 2010 | 2004 Chevrolet Blazer

    2 Answers

    I need to remove the fuel pump from my 99 chevy blazer , is there an access panel or does the fuel tank have to dropped?


    1. Properly relieve the fuel system pressure.
    2. Drain the fuel tank.
    3. Support the fuel tank.
    1. Remove or disconnect the following:
    2. Negative battery cable
    • Filler neck from the tank
    • Shield from tank and tank straps
    • Fuel lines and vapor hose from pump
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
  • To install:
    Install or connect the following:
    • Fuel pump in tank with new seal around opening

    NOTE The fuel pump strainer must be in a horizontal position when the fuel sender is installed in the tank. When installing the sender assembly, make sure that the fuel pump strainer does not block full travel of the float arm.


    • Tank and connect fuel lines and vapor hose
    • Tank to the frame. Torque the fasteners to 33 ft. lbs. (45 Nm).
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
    1. Refill the tank.
    2. Run the engine and check for leaks.
    6207c87.gif
    View of the in-tank fuel pump assembly

    Oct 13, 2009 | 1999 Chevrolet Blazer

    Not finding what you are looking for?
    2001 Ford F250 Super Duty Super Cab Logo

    Related Topics:

    25 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    fordexpert

    Level 3 Expert

    5546 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...