Question about 1995 Volvo 960

Open Question

Engin or transmision skiping

Engin or transmision skiping

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine wont start sound it as skiped a tout on timing chain has spark timing is not out what could it be


Skiped a tout? therefore valve timing is off. could be so bad that
spark and valve timeing are not right.

Dec 22, 2014 | Cars & Trucks

3 Answers

1995 isuzu rodeo is skiping


do you missing????? have you checked engine compression????? i need more info

Oct 13, 2008 | Isuzu Rodeo Cars & Trucks

1 Answer

'my 2005 jetta keeps skiping


The following are the general instructions on the start of diagnosing any electronically controlled engine or transmission problem.

The engine and the automatic transmission (transmission control is only for automatics, engine is still computer controlled no matter the transmission type) in this vehicle are computer controlled and in most cases when a fault occurs a fault code is stored in the memory of the computer control module. There are exception to this, such as the Mass Airflow Meter and fuel pressure problems. What must be done is to have all the basic testing done such as a scan of the system for fault codes as well as a check with a live data scanner tool for engine functions that are not within range of normal, a trained technician is required to know what is correct and what isn't, then based on careful diagnostics done from a factory repair manual the correct part is replaced or the wiring repaired or the computer replaced (known as the PCM), which is very rarely the problem. Other basic checks must be done as well such as mechanical problems with the engine as well as engine state of tune and mileage on the engine. The transmission can have mechanical issues as well such as no gear engagement at all or a failed pump or other pressure related problems. Also engine mechanical problems can and do cause many drive-ability related problem such as rough idle and other symptoms.

Oct 26, 2012 | Volkswagen Cars & Trucks

3 Answers

All trans to engine bolts are removed. engine mounts are free, engine still won't come out. I don't know what else could possibly be keeping it from seperating. Is it absolutely necessary to remove...


YES YOU MUST SEPERATE TO GET TO FLYWHEEL
THER IS TWO DOWEL PIN ONE PER SIDE TOWADS THE TOP OF THE TRANSMISION
PART OF ENGINE BLOCK THEY OFTEN BIT AND HOLD ON GOOD IF YOU ARE SURE THAT
ALL THE BOLTS OF THE TRANSMISION ARE UNDONE YOU SHOULD PUT THE ENGINE MOUNT BOLT BACK IN PUT JACK UNDER FRONT OF ENGINE HARMONIQUE PULLEY TO
STABILIZED MOTOR THEN WITH SECOND JACK AT REAR OF TRANSMISION JACK UP TO
START THE RELEASE THEN LOWER BACK DOWN TO RELASE TOP OF TRANSMISION
THEN WITH SUTIBLE PRY BAR BETWEEN ENGINE AND TRANS PRY APART UNTIL FREE
FIRST I WOULD UNBOLT TORQUE AND PUSH BACK IN TRANSMISION AND PUT A RETAINER TO PREVENT TORQUE FROM FALLING OUT OTHERWISE YOU WILL NEED TO CHANGE THE TORQUE PUMP INPUT SEAL IT WILL LEAK IF SEPERATED

May 26, 2011 | Ford Expedition Cars & Trucks

1 Answer

How to insall engine with manual transmision. do I insall the engine with the bellhousing atatched to the engine or the transmision


If you have removed the Radiator and cleared enough of the forward area to be able to have clearance put the engine back in with the transmission attached. If it looks like you won't have the clearance then attach the bell housing to the Transmission as you should have more room to work with the Bell housing this way although I prefer to install and remove standard mounted engines as assemblies attached to the transmission.

Sep 23, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Check engine and transmision work bad


I had the same issue. Dodges tend to have some faulty transmissions. Usually it's not too bad. I had to replace my transmission valve body. Usually a sensor or solenoid go bad. Turn the key on/off three times and it will display a code. Google the code or take it to a shop.

Mar 27, 2010 | 2004 Dodge Durango

2 Answers

I have a 82 chevy caprice when I'm driving it will stop goin forward but the engine is still going strong


Check transmision oil level, Place car in park, hand break, open motor compartment and check transmision oil level with motor on idle. Good level?: transmision is bad, repare or replace the whole unit. bad level: complete and check for leakeges.

Jul 03, 2009 | 1991 Chevrolet Caprice

1 Answer

Transmision does it affect starting


not very probable, cause the tranny is used to move the car

Jun 16, 2009 | 1994 Mitsubishi 3000GT

1 Answer

Engine skiping at idle.


If it is actually skipping, the check engine light should be on for a misfire and tell you what cylinder is missing. If it is a little bit of a rough idle, could be plugs, fuel, bad motor mount, or a bunch of other things.

Jun 09, 2009 | 2003 Cadillac CTS

1 Answer

Rough idel , cuts out while in drive , stalls ,engine skip


Take the car to a garage that has a computer. I had the same problem and it turned out to be the idler solenoid that is located on top of the engine on the fuel injector port. The computer will diagnose the problem in a short time.

Jan 21, 2009 | 1994 Buick LeSabre

Not finding what you are looking for?
1995 Volvo 960 Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...