Question about 2001 Jeep Grand Cherokee

1 Answer

How take out in disconnecting the governor pressure sensor from transmition jeep?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 159 Answers

To remove the govenor pressure sensor you have to drop the pan,remove the filter,take the torx screw out of the bracket that holds the sensor unplug the sensor and wiggle it while pulling back on it.

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 jeep code 1763 what to do


P1763 - Governor Pressure Sensor Voltage Too High

This code is refer for the governor pressure sensor which is located in the valve body of the transmission. If getting power to the sensor and the wires are not open or shorted then the sensor will need to be replaced.

GOVERNOR SOLENOID AND PRESSURE SENSOR
REMOVAL

Hoist and support vehicle on safety stands.
Remove transmission fluid pan and filter.
Disengage wire connectors from pressure sensor and solenoid (see picture)
Remove screws holding pressure solenoid retainer to governor body.
Separate solenoid retainer from governor (see picture)
Pull solenoid from governor body
Pull pressure sensor from governor body.
Remove bolts holding governor body to valve body.
Separate governor body from valve body
Remove governor body gasket.

INSTALLATION
Before installing the pressure sensor and solenoid in the governor body, replace O-ring seals, clean the gasket surfaces and replace gasket.

Place gasket in position on back of governor body
Place governor body in position on valve body.
Install bolts to hold governor body to valve body.
Lubricate O-ring on pressure sensor with transmission fluid.
Align pressure sensor to bore in governor body.
Push pressure sensor into governor body.
Lubricate O-ring, on pressure solenoid, with transmission fluid.
Align pressure solenoid to bore in governor body
Push solenoid into governor body.
Place solenoid retainer in position on governor
Install screws to hold pressure solenoid retainer to governor body.
Engage wire connectors into pressure sensor and solenoid Install transmission fluid pan and (new) filter.
Lower vehicle and road test to verify repair.

zjlimited_748.gif

1 - PRESSURE SOLENOID RETAINER
2 - GOVERNOR

zjlimited_749.gif

1 - PRESSURE SENSOR
2 - PRESSURE SOLENOID
3 - GOVERNOR


Hope helps.








Sep 29, 2011 | 2004 Jeep Grand Cherokee

2 Answers

What does code p1757 means?


Its a transmission code for the governor, the exact code description is " Governor pressure above 3psi in gear with MPH 0.
Either an input or output speed sensor is malfunctioning or the governor, governors go a lot on those transmissions.

Mar 10, 2011 | 1997 Jeep Grand Cherokee

1 Answer

Code p1762 govenor pressue sensor offset volts


P1762 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Sensor Offset Volts Too High/Low Conditions: Key on or engine running. Gear selector in Park or Neutral. PCM detected an out-of-range Governor Pressure Sensor signal for 1.3 seconds. The fault must occur 3 times on one trip to set a code. Possible Causes: Governor pressure Sensor VREF (5v) circuit is open Governor pressure Sensor ground circuit is open P/N switch is damaged or has failed (not operating properly) Transmission fluid has excessive debris or it is contaminated PCM has failed

Dec 14, 2010 | 2001 Jeep Grand Cherokee

2 Answers

Our 2003 Durango RT will not reverse while in reverse. The car just Idles there. We hear the car switch gears, but nothing happens. What could be problem?


This is one of two things, if the truck goes into drive and moves then you have trany problems and may need to have it rebuilt, if there is no movement in reverse or drive then it could be the transfer case or trany.

Dec 11, 2010 | 2003 Dodge Durango

1 Answer

2003 Durango, Truck 5.9, Car is intermittently having trouble shifting from 1 - 2nd - reves to ~3 RPM, then lunges into the next gear. I've been doing my homework on the net, but can only find info on...


Possible Cause
The following items may be area of concern:
?¬Other transmission-related DTCs are set.
?¬Solenoid pack connector 5-volt supply circuit open.
?¬Sensor signal circuit has short to ground, short to voltage or open.
?¬Governor pressure sensor defective.
?¬Transmission fluid burnt or oil pan contains excessive debris.
?¬Governor pressure out of range.
?¬Transmission leaking internally.
?¬Defective PCM.
?¬Defective valve body.

Diagnostic Procedure
1.Using scan tool, read DTCs. If good trip counter for DTC P1756 is not displayed or displayed count is not zero, go to step 25. If good trip counter is displayed and displayed count is zero, go to next step.
2.Repair any other transmission-related DTCs before proceeding. If no other transmission-related DTCs exist, go to next step.
3.Check transmission fluid for proper level and for any debris. Fill or repair transmission as necessary. If fluid level and condition are okay, go to next step.
4.Start engine. Allow engine to reach normal operating temperature. Set parking brake, depress brake pedal and place gearshift lever in "D" position. Using scan tool, observe governor pressure sensor pressure. If pressure is greater than 3 psi (.2 kg/cm 2 ), go to next step. If pressure is 3 psi (.2 kg/cm 2 ) or less, go to step 20.
5.Turn ignition off. Install a pressure gauge at transmission governor pressure test port. Start engine. With gearshift lever in "D" position, observe gauge pressure. If pressure is 5 psi (.3 kg/cm 2 ) or more, go to step 23. If pressure is less than 5 psi (.3 kg/cm 2 ), go to next step.
6.Turn ignition off. Disconnect transmission solenoid assembly connector. Turn ignition on. Measure voltage between ground and 5-volt supply circuit at transmission solenoid harness connector terminal No. 2. If voltage is 4.5-5.5 volts, go to next step. If voltage is not 4.5-5.5 volts, go to step 19.
7.Turn ignition off. Disconnect PCM harness connector C2 (White). Measure resistance of governor pressure sensor signal circuit between transmission solenoid harness connector terminal No. 4 and PCM harness connector C2 (White) terminal No. 29. If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair governor pressure sensor signal circuit for open.
8.Disconnect PCM harness connector C1 (Black). Measure resistance of sensor ground circuit between transmission solenoid harness connector terminal No. 3 and PCM harness connector C1 (Black) terminal No. 4. If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair sensor ground circuit for open.
9.Measure resistance of governor pressure sensor signal circuit between ground and transmission solenoid harness connector terminal No. 4. If resistance is less than 5 ohms, repair signal circuit for short to ground. If resistance is 5 ohms or more, go to next step.
10.Measure resistance between sensor signal circuit and sensor ground circuit at transmission solenoid harness connector terminals No. 3 and 4. If resistance is less than 5 ohms, repair governor pressure sensor circuit for short to sensor ground circuit. If resistance is 5 ohms or more, go to next step.
11.Turn ignition on. Measure voltage of governor pressure sensor signal circuit between ground and transmission solenoid assembly connector terminal No. 4. If voltage is one volt or less, go to next step. If voltage is more than one volt, repair sensor signal circuit for short to voltage.
12.Turn ignition off. Ensure transmission solenoid harness connector is disconnected. Remove transmission oil pan. Disconnect governor pressure/temperature sensor harness connector. Inspect connector and terminals for damage. Repair as necessary. Measure resistance of governor pressure sensor 5-volt supply circuit between governor pressure/temperature sensor harness connector terminal "A" and transmission solenoid harness connector terminal No. 2. If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, replace transmission solenoid assembly (internal transmission harness).
13.Measure resistance of sensor ground circuit between governor pressure/temperature sensor harness connector terminal "D" and transmission solenoid harness connector terminal No. 3. If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, replace transmission solenoid assembly (internal transmission harness).
14.Measure resistance of governor pressure sensor signal circuit between governor pressure/temperature sensor harness connector terminal "B" and transmission solenoid harness connector terminal No. 4. If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, replace transmission solenoid assembly (internal transmission harness).
15.Measure resistance of governor pressure sensor signal circuit between ground and governor pressure/temperature sensor harness connector terminal "B". If resistance is less than 5 ohms, replace transmission solenoid assembly (internal transmission harness). If resistance is 5 ohms or more, go to next step.
16.Measure resistance between governor pressure sensor signal circuit and sensor ground circuit at governor pressure/temperature sensor harness connector terminals "B" and "D". If resistance is less than 5 ohms, replace transmission solenoid assembly (internal transmission harness). If resistance is 5 ohms or more, go to next step.
17.Reconnect transmission solenoid assembly harness connector. Turn ignition on. Measure voltage of governor pressure sensor signal circuit between ground and governor pressure/temperature sensor harness connector terminal "B". If voltage is more than one volt, replace transmission solenoid assembly (internal transmission harness). If voltage is one volt or less, go to next step.
18.Turn ignition off. Using DVOM, backprobe governor pressure sensor signal circuit at PCM harness connector C2 (White) terminal No. 29. Start and idle engine. Place gearshift lever in "N" position. Using scan tool, observe governor pressure sensor voltage. Compare scan tool value with DVOM voltage. If voltages match, replace governor pressure/temperature sensor. If voltages do not match, replace PCM.
19.Turn ignition off. Ensure transmission solenoid harness connector is disconnected. Disconnect PCM harness connector C2 (White). Measure resistance of 5-volt supply circuit between transmission solenoid harness connector terminal No. 2 and PCM harness connector C2 (White) terminal No. 31. If resistance is less than 5 ohms, replace PCM. If resistance is 5 ohms or more, repair 5-volt supply circuit for open.

NOTE: Removing transmission control relay in the following step may set other DTCs. Disregard these DTCs.

Nov 28, 2010 | 2003 Dodge Durango

2 Answers

Fault codes p1757 p1762 when i doing smoke for dmv when i doing smoke test this code show fault on transmision


CODE P1757 - GOVERNOR PRESSURE GREATER THAN 3 PSI WHEN REQUESTED TO BE O. CODE P1762 - GOVERNOR PRESSURE SENSOR OFFSET VOLTS TOO LOW OR HIGH.MEANING SENSOR INPUT GREATER OR LESS THAN CALIBRATION FOR 3 CONSECUTIVE NEUTRAL PARK OCCURANCES.

Sep 01, 2010 | 2000 Jeep Cherokee

1 Answer

2002 wj jeep grand cherokee p1756


The governor pressure sensor is the most likley cause however an inspection of fluid or debris in trans pan would be a good idea to make sure there's nothing excessive in it. Attached is a list of possible causes however the senor would be the most common.

POSSIBLE CAUSES
  • Powertrain control module
  • 5 volt supply circuit open
  • Check transmission fluid level and condition
  • GOV press sensor signal circuit shorted to voltage
  • GOV press sensor signal circuit shorted to sensor ground
  • GOV press sensor signal circuit shorted to ground
  • GOV pressure sensor signal circuit open
  • Sensor ground circuit open
  • GOV press sensor signal circuit shorted to voltage inside transmission
  • 5 volt supply circuit open inside transmission
  • Intermittent governor pressure solenoid
  • Internal transmission problem
  • Oil burnt or oil pan has excessive debris
  • Other transmission DTC'S
  • GOV press sensor signal circuit shorted to sensor ground inside transmission
  • Valve body
  • GOV press sensor signal circuit shorted to ground inside transmission
  • GOV press sensor signal circuit open inside transmission
  • GOV press sensor ground circuit open inside transmission
  • Governor pressure sensor (high)

Mar 26, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Transmission problem


I had a shifting problem. The car would start in the wrong gear and shift at wrong times. I repaced the governor postion sensor and tranny fluid and the problem has been fixed for several years. Did you replace the tranny fluid?

Feb 03, 2009 | 2001 Jeep Grand Cherokee

1 Answer

I have a 1997 Jeep Grand cherokee with code 1762


1762 has to do with too high or too low voltage from the governor pressure solenoid valve in the transmission.
To test this code accurately, you would need to have Chrysler connect their scan tool to it. With that, they can check the whole system.
The governor pressure sensor measures output pressure of the governor pressure solenoid valve. It is located in the governor body on the valve body transfer plate.
It is not very difficult to replace, 83248769.gif
86167041.gif

Jan 10, 2009 | 2000 Jeep Grand Cherokee

1 Answer

2001 jeep grand cherokee transmission revving-codes p1757, p1762


P1757 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Above 3 PSI In Gear At 0 MPH Conditions: Engine started; vehicle driven to a speed over 30 mph, and the PCM detected the Governor Pressure Sensor was more than 3 psi with the requested pressure at 0 psi (95% duty cycle command) for 2.65 seconds. The fault must occur twice on one trip to set the code. Possible Causes: Check for the presence of other A/T related trouble codes Governor pressure Sensor is damaged or has failed Governor pressure Sensor VREF (5v) circuit is open or shorted Transmission valve body is leaking, damaged or has failed PCM has failed P1762 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Sensor Offset Volts Too High/Low Conditions: Key on or engine running. Gear selector in Park or Neutral. PCM detected an out-of-range Governor Pressure Sensor signal for 1.3 seconds. The fault must occur 3 times on one trip to set a code. Possible Causes: Governor pressure Sensor VREF (5v) circuit is open Governor pressure Sensor ground circuit is open P/N switch is damaged or has failed (not operating properly) Transmission fluid has excessive debris or it is contaminated PCM has failed

Nov 17, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
2001 Jeep Grand Cherokee Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...