Question about 2003 Toyota Land Cruiser

1 Answer

Have had dual battery system installed with

In 2003 Prado Diesel I have had dual battery system installed with battery disconnect. Now have to enter security code for radio (which I have) but don't know how. What do I need to do to enter code? Thankyou

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Visited local Toyota dealer and got copy of radio operation book relevent to my vehicle which contained info on how to fix. If I hadn't had security code Toyota dealer could have attached system to diagnostic computer and resolved the issue - not sure at what cost.

Posted on Oct 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Prado 2003 3 liter diesel struggles to start?


You don't say how many miles? When it was last serviced? Have you checked there is 12v at the heater plugs? Have you removed the heater plugs and tested them individually?

Aug 15, 2016 | Toyota Cars & Trucks

1 Answer

My 2003 diesel prado gives off a heavy puff of white smoke smelling of diesel when I start it cold, the engine also have a uneven idle for the first few seconds.


sounds like injector is leaking letting fuel leak into a cyclinder the smoke is raw unburned fuel then it takes a minute or so to clear the cyclinder

Dec 17, 2014 | Cars & Trucks

1 Answer

Where is the ckp sensor located on a 2003 ford f350 6.0 diesel?


Removal and Installation
  1. Disconnect the LH and RH negative battery cables. For additional information, refer to Section 414-01.
  1. NOTE: The crankshaft position (CKP) sensor is located underneath the air conditioning compressor.
    Remove the nut and position the positive battery cable and bracket aside.
    a0068391.jpg
  1. Remove the bolt and position the battery negative cable aside.
    a0068392.jpg
  1. Disconnect the CKP sensor electrical connector.
    a0065610.jpg
  1. Remove the bolt and the CKP sensor.
    a0065611.jpg
  1. NOTE: Apply clean engine oil to the O-ring before installation.
    To install, reverse the removal procedure.

Aug 29, 2011 | 2004 Ford F350

1 Answer

How do I remove the alternator on my 1998 Dodge 1500 4wd?


WARNING: DISCONNECT NEGATIVE CABLE FROM BATTERY BEFORE REMOVING BATTERY OUTPUT WIRE (B+ WIRE) FROM GENERATOR. FAILURE TO DO SO CAN RESULT IN INJURY OR DAMAGE TO ELECTRICAL SYSTEM .

  1. Disconnect negative battery cable at battery. Diesel Engines: Disconnect both negative battery cables at both batteries.
  2. Remove generator drive belt.
  3. dak408_183.gif

  1. Remove generator pivot and mounting bolts/nut. The diesel engine uses a bolt at top mounting and a bolt/nut at lower mounting. Position generator for access to wire connectors.
dak408_184.gif
  1. Remove nuts from harness holddown, battery terminal, ground terminal and 2 field terminals. Remove wire connectors. A typical generator wiring harness is shown in. Wiring harness routing as shown may be slightly different depending on vehicle model and/or engine.
  2. Remove generator from vehicle.
INSTALLATION
  1. Position generator to engine and install wiring to rear of generator. Tighten all wiring fasteners as follows:
    • Battery terminal nut-8.5 N.m (75 in. lbs.)
    • Ground terminal nut-8.5 N.m (75 in.lbs.)
    • Harness holddown nut-8.5 N.m (75 in. lbs.)
    • Field terminal nuts-2.8 N.m (25 in. lbs.)
  1. Install generator mounting fasteners and tighten as follows:
    • Generator mounting bolt-All gas powered engines-41 N.m (30 ft. lbs.)
    • Generator pivot bolt/nut-All gas powered engines-41 N.m (30 ft. lbs.)
    • Generator mounting bolt-Diesel powered engines-54 N.m (40 ft. lbs.)
    • Generator pivot bolt/nut-Diesel powered engines-54 N.m (40 ft. lbs.)

CAUTION :
  • Never force a belt over a pulley rim using a screwdriver. The synthetic fiber of the belt can be damaged.
  • When installing a serpentine accessory drive belt, the belt MUST be routed correctly. The water pump will be rotating in the wrong direction if the belt is installed incorrectly, causing the engine to overheat.
  1. Install generator drive belt.
  2. Install negative battery cable(s) to battery(s).

Dec 13, 2010 | 1998 Dodge Ram 1500 4WD

2 Answers

Toyota Prado Diesel. Electric windows do not operate


Hello! Turn the ignition switch on...Hold the master power window auto up switch for five seconds...Send a comment with results...


Guru........Saailer

Apr 11, 2010 | 2004 Toyota Land Cruiser

1 Answer

120 series prado diesel d4d aircon and indicators not working


Hi,

Have any luck with this as I have exactly the same problem except the ign2 fuse under the dash also keeps blowing. Alternator does not appear to be charging either.

Feb 07, 2010 | 2007 Toyota Land Cruiser

Not finding what you are looking for?
2003 Toyota Land Cruiser Logo

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...