Question about 2000 Renault 181

1 Answer

My car shows "door open" signal ON when I turn my car. Although I checked the doors manually. I have central locking system with remote control. This problem started since last 15 days initially when I turn my car the ceiling bulb glows which was set on door possition, now since one day the hazard lights(signal) are also getting "ON". please suggest me solution. Thank you.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 55 Answers

Sounds to me like you got a wiring problem, a bad earth connection, its earthing out through your interior light, hence your light glows dimmly. The door open switch works by creating a direct to earth connection when door opened. Locate the switch, either in the door or a plunger switch that the door closes onto. Take it out & clean it.

Posted on Oct 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Central locking opens all doors but when i go to pull open my door it locks them all.


Most central locking systems are controlled by a electronic module of some kind . BCM - body control module . Different car manufactures call them by other names. ford - SJB smart junction box , Chrysler - BCM or TIPM - totally integrated power module . Well enough of that , these modules receive input signals from door sensors , The little light on the dash that shows a door is open , door ajar switch etc.... Do the doors lock again when opening any other door on the vehicle ? If not there could be a problem with the door ajar switch inside the drivers door . And most central locking systems are not suppose to let the doors lock with the key in the ignition . There may also be DTC's - diagnostic trouble codes stored in the BCM or what ever module your vehicle make calls it . I suggest you take you vehicle to a good local independent repair shop or dealer , that has a professional grade scan tool . Auto parts stores do not have a scan tool that can check BCM codes. Nor can a simple code reader . I suggest you watch this guy's videos . Not the same problem as yours but will give you some idea what can happen when sensor inputs act up . Door Locks Go Crazy 1 If you look at the door jam with the door open you'll see a rubber boot going from the door to the car body. There are wires in side . that go to the power windows an locks . B+ an ground wires etc.... From hundreds of times of opening an closing the door , wires can an will break sometime causing strange problems .

May 06, 2016 | Cars & Trucks

1 Answer

My right side passenger door does not lock automatically anymore. Is there a fuse that operates this.


no all is related to one fuse you can remove the door internal controls and decore and remove center lock motor plug and test two connectors with multimeter with set on 12v and then lock un lock door and check the reading of the multimeter if it read signal then all plugs and wires from central lock control unit to the door central lock unit is okay it this cae you have to replace the door central lock unit with the same if no signal is readed while you lock unlock the door then you have to check central control unit and all wire plus out of it to the door plug

2- you can remove central control unit from driver door and test it in passenger door (usually the same unit ) if it works with lock unlock its then the replaced unit is faulty and needs to be replaced if it not work then check plugs wires from central lock unit (usually found inside driver door ) to the central lock unit in passenger door

3- check signal for said door fro the output of central door unit if no signal then it mean that faulty central lock control unit

Feb 23, 2015 | 2005 Honda Accord

1 Answer

Central locking system


check central locking system fuse it controls all door locks and other acessories.need go to dealership buy remote keys..

Mar 28, 2013 | 2000 Volvo S80

1 Answer

I have a 2006 VW Passat. Unable to unlock the car doors with the key fob (no manual key at all or even keyholes in the doors sadly) so this is my only way to get in the car. Every other button works on the...


The control unit (comfort system central control module) that opens the doors from the fob signal is usually under the dash on the driver's side. You cam see it on page 7 or so of the diagrams at http://www.revbase.com/BBBMotor/Wd/DownloadPdf?id=132991

Since the other fob features are working, it might be that the module just doesn't recognize the signal the fob is sending.
Or maybe the fob is not sending a signal at all. Very hard to troubleshoot, but you can check to see if the control module is sending voltage to the locks by probing the connectors on the module.

Aug 01, 2017 | Cars & Trucks

1 Answer

Need a central locking diagram for a citroen xsara xs picasso


Just do it today, in driver's side door, wires from manual keylock door switch, white wire-lock, green wire-unlock, whitegreen-ground, system is negative trigger on both wires (white-green), your black box for remote control should be configured for "Negative control signal". +12v from window electric motor (xara picasso 1.8 16v 2002' Bosnia)

Jun 04, 2012 | Citroen Xsara Cars & Trucks

1 Answer

How do i reset central locking on a micra 04 reg


Try the following:

"KEY FOB PROGRAMMING
NISSAN
SYSTEM DESCRIPTION
The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and hazard reminder. When the doors are locked and
unlocked the unit flashes the hazard lights once for lock and twice for unlock.
A maximum of four remote controls are allowed to be programmed.
ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II
Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.
Procedure
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key?s.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key?s for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds."

Mar 12, 2012 | Nissan Cars & Trucks

2 Answers

My Mitsubishi colt CZ1 (07 plate) has problem with cental locking. I can manually central lock but with the remote it locks/unlocks all the doors except the driver's door. Please help. Thanks


Central locking works by way of little electric motors that engages and disengages the door lock. The drivers door has an additional set of contacts in the actuator which signal the controller when it changes position. The controller activates the servo motors when a signal is received from the receiver or from the drivers door servo motor. So in your case I suspect the motor part of the drivers door actuator is done for.
To replace you will have to remove the inner driver's door panel to get at the actuator. The actuator itself cannot be repaired and needs to be replaced as a unit.

Apr 29, 2011 | 2006 Mitsubishi Colt

2 Answers

Central locking not operaiting


Was the car battery disconnected before this central locking problem.Also is the central locking system operated by remote.If yes,then is the remote battery new or old.If the battery in remote is old then try with new battery.Also if the central locking is controlled by a push button in the car then it can be the problem with push button switch .The switch on driver side is got short.It has to be checked with meter to confirm the fault.Apply a direct 12 volt external battery to the switch and check if the central locking is getting done.Also confirm if you can lock the doors manually by using a car key.If you are not able to lock the door with key manually then its faulty door latch.But if the door lock and unlock manually with out any problem then this problem is related to central locking switch or the remote.

Nov 08, 2010 | 2003 Kia Sedona

1 Answer

Passenger door not opening with central locking


1st wind the glass down and turn the key in the driver door twice in clockwise direction to lock, at the sound of the second click try try opening the door thru the window (passenger) manually. you will need to pull the knob twice before it opens. you can get all the passenger doors open this way until you decide to change central lock system. To activate the remote; insert the key into driver door while pressing the lock or unlock button on the remote for at least five-ten seconds which should get it functioning normally again. hope this helps. it worked on mine.

Aug 07, 2008 | 2002 Audi A6

1 Answer

I have a bmw 316ti compact on a 52 reg. The central locking gave up working 3mths ago and we was useing the key to lock and unlock the car,then all ov a sudden we couldnt start the car.when you put the...


with any BMW they have their problems, one is the central locking/immobilizer, the central locking is linked into the immobilizer and vice versa, the immobilizer takes it signal to disarm from the central locking and the ignition key ring. (chip in the key) if one of these starts to play up it has loads of consequences this being one of them. they all need to work together for the system to work properly. you would need to read the alarm and immobiliser codes using an ob2 tool that can detect them, and find the fault some problems it can be the drivers door sensor in the lock this is the main door as its drivers side and it controls all other doors on the central locking. if the switch is worn in any of it movements the system will not know the door has been opened, this does not work on the interior light as that is a switch in the door frame. the door lock is lock unlock and deadlock with key with remote fob its also arm disarm alarm and immobiliser. i have seen in some models there is a sensor auto lock so when you walk away with the key the doors lock automatically all lease parts work together. any one having a problem can cause no signal to be sent to the others in the system to start engine .

Jun 22, 2017 | BMW 318 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

xxxxxx xxx

Level 3 Expert

4844 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...