Question about 1998 Dodge Intrepid

2 Answers

My dodge intriped cannot start after i try allmost everything

I have a dodge intriped and i cannot get this thing to start.the engine spin but no fire in the coil . i know that the camshaft position sensor is good because i change it. and i turn the ignition on. and remove the sensor and plug it back up and i can hear the engine engaged

Posted by on

  • Jonah Oneal Jan 02, 2012

    check 20 AMP fuse to ASD RELAY. if fuse okay problem could be pcm not sending power to ignition coil circuit or ASD RELAY could be faulty.

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 14,036 Answers

SCAN IT.TO SEE IF YOU HAVE PCM FAULT CODES.

Posted on Sep 30, 2009

  • 1 more comment 
  • Jonah Oneal Sep 30, 2009

    SCAN IT PROBLEM COULD BE CRANK SHAFT SENSOR NOT WORKING .COIL IS OPEN FAULTY PCM.ALL OF THESE COMPONENTS CONTROL YOUR SPARK.CAM SHAFT SENSOR CONTROL INJECTOR TIMING.SCAN IT TO LOOK FOR PCM CODES OR CKP CODES.

  • ktm26983 Jan 01, 2012

    I have the same thing going on with my 01 2.7 wish some one had a answer

  • ktm26983 Jan 01, 2012

    My 98 2.7 went out so I put a 2001 2.7 i made sure every thing was hooked up but not getting spark at all but before I change out engines it worked so I Ann really stumped on this

×

Ad

I think your best bet is a repair shop or dealer because you may not have the knowledge to fix. Not being hurtful just realistic

Posted on Sep 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Install stater on 97 dodge intriped


The starter is on the bottom side of the engine where the transmission connects.

Dec 22, 2012 | 1997 Dodge Intrepid

1 Answer

Replace the water pump and timing belt on a 2002 dodge caravan 2.4 lt. Now the engine rotates but does not start you can hear the starter spinning. What could it be?


You could have forgotten to try and crank-up the car before you bolted things back again. This would have allowed you to correct any mistake. Try and rotate the distributor (if it has one) while an assitant cranks the engine. If it does not fire up, remove the #1 spark-plug, hand turn the crank-pulley,and get it to BTDC. Replace the sparkplug, and crank up the engine again. If it does not fire, try the plug wires, and get them in proper firing-order. A shop manual such as Haynes is one of your best bets to do a job like this.

Nov 11, 2009 | 2002 Dodge Caravan

1 Answer

My intriped cannot start


try coil pack or crank sensor

Oct 01, 2009 | Cars & Trucks

2 Answers

I have a 1998 dodge intriped cranks over but


I just fixed one like yours. When its is very quite near your car turn the key to the run position while listening for the electric fuel pump to run for a couple of seconds. It should be heard every time you put the key in the run position. The pump is in the gas tank.If you cannot hear it then take all the stuff out of your trunk so some one can get in and help you listen. There is a access cover in the back of the trunk that covers the pump. Have the person listen right on top of this cover. If you cannot hear the pump its probably worn out and needs replaced. There is also a fuel pump fuse and a relay. Check the fuse. The relay is under the hood and has many other relays next to it. I just swapped the pump relay with the one next to it to see if the pump would run. All the relays in my Dodge had the same part number on them. They use the same relay in many dodge things in our cars.
Then...after I replaced the pump my car seemed to be running on only 5 cylinders. I had to replace the coil pack under the hood.One of the six sparkplug wires stopped getting spark.
Now she runs like new...
I hope this helps you.

Aug 28, 2009 | 1997 Dodge Intrepid

2 Answers

Need pics where cam sensor is located on the engine of a 1999 2.7 litre dodge intriped


driver side of engine only plug right below valve cover going into the head almost L shaped and black

Feb 21, 2009 | 2004 Dodge Intrepid

1 Answer

Well i have a dodge intriped 1998 and i change the engine, starter and steering colum and i cannot start the car. and i tested everything so far. so i guess i,m ready to try your solution . where do you...


Battery temp sensor won't stop it from starting! that will cause check engine light to appear! I would look into seeing if you have all your wires directly connected and run a OBD 2 scan if engine light is on should be on ! and find out what sensor is not connected!

Jan 16, 2009 | 1998 Dodge Intrepid

1 Answer

I would like a dodge expert to help me with this problem


If the engine is a 2.7L. What is most likely wrong is his. The engine out of the 2001 has a different timing gear on the left cylinder head then the one on the 1998. In 1998 the engine computer is a SBEC controler(single board engine controler) an the 2001 is a NGC controler(next generation controler) the timing windows on those gears are in different positions. The controler doesnt know where the timing is.

Jan 16, 2009 | 1998 Dodge Intrepid

2 Answers

Thank you mr phil for your concern. my dodge intriped cannot start after i change motor


It could be worth double checking that the ecu for your old motor is compatable with the new one as within 3 yrs a lot of changes can be made by the vehicals manufacturer

Jan 08, 2009 | 1998 Dodge Intrepid

1 Answer

Dodge intiped cannot start after change engine


Was the shims used from the old engine? Possible the gear on the starter is worn ? Also check compatibility between the year models.

Dec 26, 2008 | 1998 Dodge Intrepid

1 Answer

I,m taking out my intriped engine can it come up or do i have to


it is designed to be removed from the bottom after removing subframe with transmission together..then split...it is possible to do from top but nearly double the work

Dec 02, 2008 | 1999 Dodge Intrepid

Not finding what you are looking for?
1998 Dodge Intrepid Logo

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...