Question about 1991 Honda Accord

1 Answer

How tight should head tork bolts be on a 91 honda accord

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 122 Answers

On the 90-93 accord, tighten the bolts to 29 ft lbs on the first pass, 51 ft lbs on the second, and a final torque of 78 ft lbs, if you have a V-6 29 on the first and 56 on the second and final pass always start from the middle an work your way outward in balance 8,6,2,4,10 upper lower 9,3,1,5, 7 I hope this solves your issue, good luck!

Posted on Sep 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove front seat 91 honda accord


look 4 body bolts ,possible (torx head) you should only have to loosen them unless you have a great need to remove seat ,seat belt will also have to be removed at floor and a good chance there will be electrical connections to on board computer -bcm or air bag srs .

Oct 02, 2012 | 1991 Honda Accord

2 Answers

Head torque specs for 92 honda accord with f22a1


Thanks for using FixYa.

To install:
  1. Install a new head gasket on the engine, making certain it is positioned correctly. The cylinder head dowel pins and the oil jet must be in place. Refer to the illustrations if necessary.
  2. Install the head. Lower it straight down onto the block, aligning it correctly.
  3. Apply clean engine oil to the bolt threads and the contact face of the bolt head. Install the head bolts finger-tight.
  4. On all models except 1988-89 DOHC Prelude and 1992-95 Preludes with 2.3L and VTEC engines, tighten the head bolts following sequence A. On 1988-89 DOHC Preludes, use sequence B. Use sequence C on 1992-95 Preludes with 2.3L and VTEC engines.
    1. On 1984-89 Accords and 1984-91 Preludes, tighten the bolts in two passes. The first pass should bring the bolts to about 22 ft. lbs. (30 Nm). On the second pass, tighten the bolts to their final torque of 49 ft. lbs. (68 Nm).
    2. On 1990-93 Accords, tighten the bolts to 29 ft. lbs. (40 Nm) on the first pass, 51 ft. lbs. (70 Nm) on the second pass, then tighten the bolts to their final torque of 78 ft. lbs. (108 Nm).
    3. On 1994-95 Accords and 1992-95 Preludes, the bolts are also tightened in three passes. Tighten the bolts to 29 ft. lbs. (40 Nm) on the first pass, 51 ft. lbs. (70 Nm) on the second pass, then tighten the bolts to their final torque of 72 ft. lbs. (100 Nm).

      0900c152800b80b4.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Fig. 9: Cylinder head bolt torque sequence A

      jturcotte_2331.gif

      Fig. Fig. 10: Cylinder head bolt torque sequence B


      0900c152800b80b6.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Fig. 11: Cylinder head bolt torque sequence C


  5. If applicable, assemble the intake and exhaust manifolds to the head. Use new gaskets.
  6. If applicable, install the cam, rockers and camshaft holders.
  7. If equipped, install the EGR crossover and air suction pipes.
  8. Connect the exhaust pipe to the manifold using new nuts.
  9. Install the timing belt.
  10. Install the valve cover.
  11. Install the cylinder sensor (if equipped) and the distributor.
  12. If applicable, install the alternator.
  13. Install the power steering pump, then connect the inlet hose to the pump.
  14. Install the accessory drive belts. Adjust the belt tensions.
  15. Install the heater hoses.
  16. Install the cruise control actuator if it was removed.
  17. Connect the spark plug wires. Connect all the wire harnesses and vacuum hoses to the cylinder head, intake manifold and throttle body/carburetor.
  18. Connect the throttle control cable and/or accelerator cable at the throttle body.
  19. Connect the fuel lines.
  20. Install the brake booster, PCV and charcoal canister vacuum hoses.
  21. Install the air cleaner and intake duct.
  22. Refill the engine coolant. It is recommended that the engine oil be changed whenever a cylinder head is removed.
  23. Connect the negative battery cable.
  24. Start the engine, allowing it to idle. Bleed the cooling system. Check the work area carefully for any signs of fluid leakage or any indication of the timing belt rubbing or slapping the covers.

Sep 25, 2011 | Honda Accord Cars & Trucks

1 Answer

Head bolt specs for a 91 honda accord 2.2l


Tighten the bolts in a pattern as such; 8 6 2 4 10
9 3 1 5 7 So if you were looking straight down onto the head, the first bolt you'd tighten would be the center one, closest to you. The second bolt you'd tighten is the center one farthest from you. The 3rd would be one left for middle closest to you, 4th would be one right from center, farther from you...Make sence? Tighten them all in that sequence, to 29 ft-lbs. After they are all tightened in that order, start from 1 and tighten them all to 51ft-lbs. Then finally, tighten them all down to 72ft-lbs. Make sure to follow that order every time. If a bolt makes a wierd noise while you are tightening it, loosen the bolt, and retorque it from the 1st step.

Jun 12, 2010 | 1991 Honda Accord

2 Answers

I have a 91 honda accord ex, one of the front lug


If you undid the hub nut and retainer ring with clip it should tap off once brake caliper is removed.

May 15, 2010 | 1991 Honda Accord

1 Answer

Hello I have 6.0L diesel need the torque sequence for the heads


If it's a 6 or its a V-8 it does not matter as long as you start from the center and work your way out to both ends I will do it by numbers using an example of 10 bolts like this do this on both heads and follow the same pattern for the intake system. also go from slightly tight just touching 5 pounds then re due it at 20 pounds then again at 40 pounds then 60 and finally to the exact tork setting using a maker double check the bolts one by one and mark with ink so you know that one is done on the last tork setting give it just a slight click past the exact tork.hope this heps.

9 5 1 3 7
10 6 2 4 8

Jan 19, 2010 | 2004 Ford Super Duty F 450

2 Answers

Need torque settings for honda ballade cylinder head bolts


dear friend-your torque setting is cold 66 nm

Jul 23, 2009 | 1998 Honda Civic

1 Answer

Headlight bezel replacement


first i wanna say good luck too you..I don't know who dizayn that head light assmebly but it was the stupidist think i ever seen..
My friend 1992 accord had a broken head light and he asked me the favor and i thinked just the headlight why not...
first i had to remove front grill and side marker find one bolt under side marker but it dosent change anything then i figure it out whole think!!!!!
You have to remove whole bumper cover and bracet to remove bottom screws 3 on inside 2 on out side of head light...
i have to spend hours to replace 40 bucks head light..

May 03, 2009 | 1991 Honda Accord

3 Answers

How do I loosen the bolt on crank shaft?


Hi Manuel

The bolt comes off, in an anti clockwise direction.

I normally put a socket on an extension bar, with metal tube, to extend the length, on to the crank pulley bolt.

Secure under the vehicle with wooden block, and spin he starter, this will loosen it off no problem.

But this procedure must be carried out, before the cam belt timing is disturbed.

Airgun can be used to replace the bolt.

Good Luck !

A FixYa rating would be Nice......Thank you ! John.



Feb 16, 2009 | 1999 Honda Accord

2 Answers

Bumper cover removal


Its easy look at the bottom of the bumper has retainers and the fenders have a bolt on each side then just slide off

Jan 23, 2009 | 1991 Honda Accord

4 Answers

Chevy 5.7 17 bolt heads tork specs


Cylinder Head Bolt (Preferred Method) All Bolts First Pass in Sequence 22 ft.lb Long Bolt Final Pass in Sequence 75 deg. Medium Bolt Final Pass in Sequence 65 deg Short Bolt Final Pass in Sequence 55 deg. Cylinder Head Bolt (Optional On-Vehicle Strategy) First Pass in Sequence 26 ft.lb Second Pass in Sequence 44 ft.lb Final Pass in Sequence 66 ft.lb

Oct 13, 2008 | 1999 Chevrolet C1500

Not finding what you are looking for?
1991 Honda Accord Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...