Question about 2003 Mazda Protege

1 Answer

I have changed the motor on my mazda and i does not want to start, there is nofuelcoming

Posted by on

1 Answer

You did this all by yourself , you did not pay someone? Give us more, like the tests you ran and the areas you suspect the problem.

Posted on Sep 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 2.6 mazda proceed there's a light on dash that says heat came on yesterday so left over night when started light came back on have just bought vechicle and had changed oil and filter


Are you saying temp light came on? Check radiator coolant, and if low use instructions to refill. if coolant is ok, check if hose going from top of radiator to motor is warm after running for five or ten minutes. if not shut motor off and dont drive it. You probably need to change the thermostate where the hose goes to motor. if you continue driving you may blow a headgasket. A thermostat is an easy replacement. Two bolts. just make sure you place it right side up.

Sep 03, 2016 | Mazda Cars & Trucks

1 Answer

My 2004 Mazda tribute has started shuddering in all gears, not contuously but seems when it drops below the 2 on rpms. Had just had it serviced and oil changed 2 weeks ago


Did you have the motor oil changed or the transmission oil? Your check engine light should be on and you should have it scanned by a professional. Did it start to shudder immediately after the service? Its very hard to tell without seeing the car to diagnose myself.

Mar 09, 2016 | Mazda Cars & Trucks

1 Answer

Change motor mount on a 04 mazda 6


FIRST YOU'LL NEED TO SUPPRT THE MOTOR WITH A JACK! UNBOLT THE MOUNT FROM MOTOR, JACK THE MOTOR UP TO CLEAR MOTOR MOUNT, AND UNBOLT IT FROM THE FRAME! REPLACE IT, BOLT THE MOUNT TO THE FRAME FIRST, THEN LOWER THE MOTOR BACK INTO THE MOUNT, AND REBOLT THE MOTOR!

Feb 27, 2011 | 2004 Mazda 6

1 Answer

Why mazda car are very heatup


You cant Ad a Bigger Rad if you Like Or Change Your Thermostat inside you Water Pump... but ..The Motor as to be on Specific Heat Temperature for Good Performance ....Try to change your Thermistor Delay Lower Heat Resistance to make your Fan start at low temperature.. You can not leave your fan on all the time... You may damage it Put Extras Fan on rad will help

Oct 07, 2010 | 2005 Mazda RX-8

1 Answer

Hi! my name is Carlos I Have a Mazda Protege 99


Check the plugs for spark, pull one out and lay it on a metal part with the wire attached,, crank it over and see if it sparks, if yes, then squirt some fuel in the throttle and see if it fires, narrow it down to something. Check the oil, the electrical sensor in the header is an oxygen sensor, it will not effect the engine, If you don't have a spark, pull the coil pack off the old engine and bolt it on the new one. Check it out.

Jun 22, 2010 | 1999 Mazda Protege

1 Answer

I can start my Mazda 626. After driving 500 meters motor stops. I have to wait about 5 minutes til I can restart. Then it works without any problem.


I would check the coil witch is inside the Distributer. Just get a whole Distributer and change it. It could also be leads but thats unlikely.

Dec 11, 2008 | 1994 Mazda 626

1 Answer

Mazda


its a shot in the dark but i had the same sort of problem. make sure all your earths are sconnected. The problem i found was that it was a voltage drop. try charging the battery and starting.

Dec 04, 2008 | 1994 Mazda 626

Not finding what you are looking for?
2003 Mazda Protege Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...