Question about 1996 Jeep Grand Cherokee

1 Answer

How do i replace the heater core on a 1996 Grand Cherokee 6cyl. 4wd?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers

REMOVAL AND INSTALLATION

Note:
This revised Heater A/C Housing service procedure is referenced from Technical Service Bulletin No: 24-02-98. Removal

  1. Disconnect battery. This must be done to prevent accidental airbag deployment.
  2. Using on A/C recovery unit, remove all R-134a refrigerant from the A/C system. See: Service and Repair
  3. Remove the shift knob by pulling sharply upward.
  4. Place the transfer case in low range. Pry the shift indicator bezel out of the console using a trim stick.
  5. Apply the parking brake and place the transfer case in neutral. Remove the parking brake trim insert. Remove the console attaching screws. Lift the console up and disconnect the 4WD indicator lamp hamess. Remove the console.
  6. Remove the passenger side knee blocker. Remove the single end screw. Remove the screws below the glove box. Remove the screw at the courtesy lamp. Remove the ash receiver and the screws behind it. Remove the instrument panel armature screw behind the ash receiver. Open the glove box and remove the screws behind it. Lower the panel and disconnect the lamp harnesses. For additional instrument panel service procedures to complete steps 6 thru 25, refer to Instrument Panel, Gauges and Warning Indicators/ Instrument Cluster / Carrier/ Service and Repair/ Procedures. See: Instrument Panel, Gauges and Warning Indicators\Instrument Cluster / Carrier\Service and Repair
  7. Remove the pod switch bezels on both sides of the steering column with a trim stick.
  8. Remove the drive side knee blocker. Remove the end screw and screws located at the bottom of the knee blocker.
  9. Remove the cowl top trim panel by prying it up with a trim stick. Remove the solar sensor if equipped.
  10. Remove the "A" post trim panels.
  11. Remove the remove the bolts that attach the lower instrument panel reinforcement to the instrument panel armature and remove the reinforcement.
  12. Disconnect the park lamp switch.
  13. Pull back the carpet at the transmission tunnel from the base of the instrument panel center bezel. Remove the nuts from the upper studs and bolts through the floor that secure the instrument panel center bracket.
  14. Remove the bolts that secure the instrument panel center bracket to the drivers side of the transmission tunnel.
  15. Remove the screws securing the Vehicle Information Center and remove it. Remove the screw fastening the mounting bracket.
  16. Unplug the vacuum harness connector or vent tube on ATC equipped vehicles and the wire harness located under the passenger side of the instrument panel.
  17. Remove the screws holding the passenger side kick panel, along with the screw from the kick panel shroud.
  18. Unplug the antenna cable near the right cowl side panel.
  19. Unplug the instrument panel wire harness connectors from the junction block at the right cowl side panel.
  20. Remove the bolts that secure the instrument panel armature to the windshield fence.
  21. Remove the nuts that secure the top if the instrument panel armature to the windshield fence.
  22. Remove the bolts that secure the ends of the instrument panel to the cowl side panel.
  23. Remove the nuts that secure the steering column to the brake pedal support and lower the steering column.
  24. Remove the bolts that secure the instrument panel armature to the brake pedal support.
  25. Place a protective cover on the seats. Lift the instrument panel off the windshield fence studs and maneuver the instrument panel out and lower it onto the seats.
  26. Disconnect the refrigerant lines from the evaporator tubes. Make sure to install plugs or tape the ends of the lines and fittings to ensure that excessive amounts of moisture do not contaminate the A/C system.
  27. Remove the vacuum line at the tee from the main vacuum supply harness. This line runs through the body with the upper refrigerant line.
  28. Disconnect the heater hoses from the heater core and clamp the ends closed to prevent coolant loss. See: Heater Core\Service and Repair
  29. Remove the coolant overflow bottle.
  30. Remove the Powertrain Control Module with connectors intact and set aside.
  31. Remove the heater A/C housing mounting nuts from the studs on the engine compartment side of the dash.
  32. Remove the heater A/C housing from the vehicle.
  33. To Install the components, reverse the procedure stated above. Torque Specifications: Instrument panel center bracket to floor transmission tunnel fastener: 28 Nm (250 in. lbs.) Instrument panel to windshield fence bolts and nuts: 12 Nm (105 in. lbs.) Instrument panel to cowl side inner panel bolts: 12 Nm (105 in. lbs.) Instrument panel to steering column support bolts: 12 Nm (105 in. lbs.)

Posted on Sep 30, 2009

Testimonial: "Excellent!!! Thank you very much."

  • Ronnie Wilson Sep 30, 2009

    Im SURE this Will Help You With the Heater Core REPLACMENT



    REMOVAL


    1. Remove the heater-A/C unit from the vehicle. "Housing Assembly HVAC : Service and Repair" See: Housing Assembly HVAC\Service and Repair\Heater - A/C Housing Removal and Installation
    2. Remove the heater core retaining screws.
    3. Pull the heater core straight out of the housing.

    INSTALLATION


    1. Install the heater core into the housing.
    2. Position the clips over the heater core tubes. Install and tighten the screws.
    3. Install the heater-A/C unit into the vehicle. Under "Housing Assembly HVAC : Service and Repair"

  • Ronnie Wilson Sep 30, 2009

    REMOVAL


    1. Remove the heater-A/C unit from the vehicle. "Housing Assembly HVAC : Service and Repair" See: Housing Assembly HVAC\Service and Repair\Heater - A/C Housing Removal and Installation
    2. Remove the heater core retaining screws.
    3. Pull the heater core straight out of the housing.

    INSTALLATION


    1. Install the heater core into the housing.
    2. Position the clips over the heater core tubes. Install and tighten the screws.
    3. Install the heater-A/C unit into the vehicle. Under "Housing Assembly HVAC : Service and Repair"

    THIS IS WHAT YOU NEED Good Luck ! , RejakWilson

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 jeep cherokee clattering noise when starting in first gear


Very Hard to say where a Clatter is coming from.
Do you have an Automatic or Manual Transmission?
Does it make a noise when you are turning and it stays in 4WD?

Feb 13, 2014 | 1998 Jeep Cherokee

1 Answer

I need to know how to replace a heater core in 1996 jeep grand cherokee loredo


the dash has to be remove on jeeps and dodge,it's alot of work and thakes about 4 hours to replace good luck.

Nov 08, 2012 | 1996 Jeep Grand Cherokee

1 Answer

1996 grand cherokee-6cyl When making tight turns,


Hi, the likely problem is a worn out CV joint on one of your axles. Check for a torn boot on either axle. Once a toot tears open, dirt gets in and wears out the joint. Please let me know if you have more questions, and thanks for using FixYa.

Aug 03, 2011 | 1996 Jeep Grand Cherokee

1 Answer

Would a 1998 grand cherokee Trans fix a 1994 grand cherokee both 6cyl 4wd?


No, the drive train and shafts are different, this includes the linkage and other components.

Jun 03, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Where is the flasher located


1996 Jeep Grand Cherokee 4WD 4.0L MFI 6cyl:
The Flasher is located front seating area, driver side, under dash, driver side of steering column, mounted in convenience center.
Application:
- Hazard flasher
- Turn signal

Check the ZJ-Secc-8W-Wiring-Diagrams (page 8) for Convince Center graphics.

I really hope helps with this (remember rated this help) Good luck.

Dec 29, 2009 | 1996 Jeep Grand Cherokee

1 Answer

2002 jeep grand laredo blower sw not working


Have you checked the ground side of the switch?

Oct 14, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Hi, I wanted to know what is the fuel range km/liters on the hiway and in the city for a jeep grand cherokee ltd 4wd 6cyl 1996. thanks


IT DEPENDS ON HOW YOU DRIVE AND HOW WELL YOU MAINTAIN THE CAR. BUT 12 MPG IN TOWN AND 17 MPG ON OPEN ROAD WOULD BE AVERAGE FUEL ECONOMY, THIS IS A VERY HEAVY TRUCK, OVER 2 TONS.

Jun 24, 2009 | 1996 Jeep Grand Cherokee

2 Answers

1996 grande cherokee 4wd 6cyl. dies out while driving will catch up or cut off,will crank after sets awhile and runs fine for awhile.has back fired with flames from exhaust.replaced ign. coil,fuelfilter,...


it is you crank posioion sensor it is located between the motor and the bell housing on transmission on passange top bell hosing one the sensor get warm it internaly grounds it self

May 06, 2009 | 1996 Jeep Grand Cherokee

2 Answers

Need to know correct timing on 1996 jeep grande cherokee 4wd 6cyl. replaced drive belt awhile back now having problems. while driving it spits/sputters dies out & catches back up.Has back fired with flames...


Non-adjustable timing.

Firing order 1-5-3-6-2-4 ------------- front | | of | 1 2 3 4 5 6 | vehicle | | Distributor rotates clockwise ------------
The Spark Plug Gap .035 (In thousandths of an inch)

May 06, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

1,773 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...