Question about 2001 Ford Taurus

4 Answers

2001 Ford Taurus Heater blower not working - 2001 Ford Taurus

Posted by on

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Heater is not blowinig warm air.

Posted on Nov 25, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My heat isnt blowing and the thermastat has been replaced and the heating core in leaking.....whats the problem?

Posted on Nov 23, 2009

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 26 Answers

Once they go you should just go get a new one and install..simple job.

Posted on Sep 30, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Blower Motor is not blowing in my 97 ford taurus. We don't think theres power going to it.

Posted on Jun 04, 2010

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: 2002 Ford Taurus blower fan only works on high

fords are notorius for faulty fan switches, you will need to get a new one, but it will probably fail in a year or two.

Posted on Nov 11, 2008

c17hydro
  • 2984 Answers

SOURCE: how to bleed the brakes for 2001 ford taurus

Please don't forget to rate:


Bleeding The Brake System Bleeding When any part of the hydraulic system has been disconnected for repair or replacement, air enters the lines causing spongy pedal action (because air can be compressed and brake fluid cannot). To correct this condition, it is necessary to bleed the hydraulic system to ensure all air is purged.
Always begin bleeding the brake system from the furthest wheel cylinder or caliper from the master cylinder; the right rear.
NOTE: The right side of the vehicle is the passenger side. The sides of the vehicle are determined from the driver's perspective. This reference is taken from sitting in the driver's seat, facing forward.
Maintain a full reservoir during the bleeding operation. Never use brake fluid that has been drained from the hydraulic system, or from an open container, no matter how clean it is. Always use brake fluid from a new, sealed container. The front and rear reservoir will drain as the front or rear brakes are bled.

  1. Park the vehicle on a level surface. Place the vehicle in PARK (automatic) or REVERSE (manual) with the engine OFF, and apply the parking brake. Chock the rear wheels to prevent vehicle movement. NOTE: Wheel chocks may be purchased at your local auto parts store, or a block of wood cut into wedges may be used.
  2. Loosen the lugnuts from all four wheels, but do not remove the lugnuts until the vehicle is raised and supported properly.
  3. Use an approved jack and raise the vehicle high enough to place jack stands under all four corners of the vehicle. Place the jack stands under the frame or axles of the vehicle. Ensure that the front of the vehicle is raised higher than the rear.
  4. Remove the wheels from the vehicle.
  5. Clean all dirt from around the master cylinder fill cap. Remove the cap and fill the master cylinder with brake fluid until the level is within 1/4 in. (6mm) of the top edge of the reservoir.
  6. Clean the bleeder screws at all four wheels. The bleeder screws are located on the back of the brake backing plate (drum brakes) and at the top of the brake calipers (disc brakes).
  7. Attach a length of rubber hose over the bleeder screw and place the other end of the hose in a plastic jar.
  8. Have an assistant place and hold pressure on the brake pedal.
  9. Open the bleeder screw 1/2 - 3/4 turn. As the bleeder is opened, the brake pedal will travel to the floor. Have the assistant inform you when the pedal has bottomed out. NOTE: Do not remove pressure from the brake pedal once it is bottomed out. No movement to the pedal should occur until the bleeder is closed and the assistant is made aware of the situation. Failure to do this will draw more air into the system.
  10. Close the bleeder screw and tell your assistant remove their foot from the brake pedal. Continue this process to purge all air from the system.
  11. When bubbles cease to appear at the end of the bleeder hose, tighten the bleeder screw and remove the hose.
  12. After bleeding each wheel, check the master cylinder fluid level and add fluid accordingly.
  13. Repeat the bleeding operation at the remaining three wheels, ending with the one closet to the master cylinder. The pattern is, RR, LR, RF, LF.
  14. Fill the master cylinder reservoir to the proper level and install the reservoir cap.

Posted on Jul 22, 2009

emissionwiz
  • 75807 Answers

SOURCE: 2000 Ford Taurus heater blows cold air ?

this problem is caused by a part called the "temperature control blend door actuater motor" this litttle motor drive moves the door that diverts air over the heater core or AC evaporator core, when it fails it almost alwys fails in the AC only position, u will need to have the motor drive replaced

Posted on Oct 16, 2009

  • 1146 Answers

SOURCE: I need a replacement keys for 2001 ford taurus

A good place to start is a ford dealer. Often they can cut you a key off the VIN number. You will have to go there in person., and some kind of proof of ownership would be needed!

Posted on Apr 02, 2010

csmock132
  • 4669 Answers

SOURCE: 2001 ford taurus 3.0 liter ohv serpentine belt

3.0 OHV Vin U24dba77.gif

Posted on Apr 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 merury villager estate and the heater fan isn't working. Heat works fine but the fan won't come on. What do i need to do to fix it?


Charlie, 1st thing is to check your fuses. I will post some links to help you see and solve problem. May not be your exact model but steps are basically the same.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How To Install Replace Heater AC Fan Speed Resistor Ford Taurus Mercury...

How To Install Replace Heater AC Blower Fan Motor 2004 08 Ford F150


How To Install Replace Heater AC Blower Fan Motor 2000 07 Ford Focus


Feb 27, 2016 | Cars & Trucks

1 Answer

I have a 2001 ford taurus and the hearter and the defrost wont work what should i do


heater blower motor might need replaced or maybe you have a blown fuse

Jan 22, 2014 | 2011 Ford Taurus

1 Answer

2001 ford taurus heater sometimes won't work


Hey Glen,are you saying the blower doesn't work sometimes,if so then your blower motor resistor could be bad,it's located next to the blower motor,easy to remove and replace.Here's a guide to blower motor.

Jan 26, 2013 | 1997 Saturn SL

2 Answers

I have a 2001 Taurus and the heater isn't working,


You might want to check the temperature control switch. I have a problem with mine and believe that is the problem. My switch just goes round and round. If you are careful you can find a spot that produces heat.

Apr 29, 2010 | 2001 Ford Taurus

1 Answer

Which fuse operates the ac & heater blower on a 2001 ford Taurus. Box is under the hood with many empty socket and no diagram.


There is a fuse box inside the car to the left of the steering column. fuse 228 10 amp and fuse 208 40 amp. Check power to the blower motor connector. Check for water in blower. I have seen water get into blower motor and short out. Good luck I hope this helps.

Jul 30, 2009 | 2001 Ford Taurus

1 Answer

How did I get water in my 2001 Ford Taurus heater blower?


Hello, it sounds like your heater core has busted and leaking inside the car. The water in your blower may be coming from the heater care also. to be sure you can get a ethyl glycol(antifreeze) tester . Thank you

Feb 28, 2009 | 1999 Ford Taurus

1 Answer

Heater stopped working.. blower not working? 1999 ford taurus


sounds like the blower motor resistor which controls blower motor speed has a short and needs replaced.

Jan 25, 2009 | 1999 Ford Taurus

1 Answer

Ford taurus Wagon 2001 heater problem


Check your coolant level. If the antifreeze is low the water pump may not be able to pump enough of the coolant through your heater core. When the car runs faster it is able to pump more of the warm antifreeze to the heater core.

Dec 02, 2008 | 2001 Ford Taurus

Not finding what you are looking for?
2001 Ford Taurus Logo

1,223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...