Question about 2002 Ford F350 Super Duty DRW Reg. Cab

1 Answer

The rod that the oil filter screws onto has a hole on it. can i replace it?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 713 Answers

Yes you can it takes an allen head socket or wrench to take loose. I have not yet seen this part in an aftermarket replacement, will probably have to obtain from the dealer.

Posted on Sep 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 dodge 3.9l v6 what direction (up or down) do I put the oil hole on my lifters?


Hi Franklin:
All of the engines I've played with that had hydraulic lifters also had hollow push rods. The lifters act like little pumps and oil comes up through the push rods to lubricate the end of the rocker arms.
My answer:
flat end down onto the cam
hole end up for the push rod to sit in.

Aug 05, 2015 | Dodge Cars & Trucks

1 Answer

How do I replace seals in the oil filter housing for a 1988 Accura Legend V6, 2.7 liter engine?


Remove the oil filter and then remove the oil filter stud that the filter screws onto. The seal is behind the adapter plate.

Nov 04, 2014 | Cars & Trucks

3 Answers

Replacing oil pressure sensor(oil sender unit) i saw it licking oil above oil filter


It is really hard to get to, but really easy to change.

Unhook the battery cable so you don't blow the new one when you install it. Depending on the location, you may have to remove the oil filter to be able to access the sensor.

Unplug the wire off the end of the sensor, slip a socket onto the old sensor, and unscrew it like you would a spark plug. Before you out the new sensor in make sure it has Teflon tape on the threads. I always a little more than what comes with it.

Screw in the new sensor "hand tight" - then 1/4 to 1/2 turn past hand tight; do not over tighten. Plug the wire on the end. If you removed the oil filter, replace it with new one. Last step - replace the battery cable.

May 28, 2014 | 2002 Buick Rendezvous

1 Answer

Oil leaking from above the oil filter


I had this problem on my 06 G6. The oil filter housing gasgket needed to be replaced. The oild filter housing is what the oil filter screws onto, and the housing attaches to the block of the motor, and theres a gasgket inbetween the block and housing. The oil filter housing is held on with three screws, and one is extremely difficult to get to. I also had to remove the belt and unbolt the a/c compressor.

Apr 13, 2014 | 2006 Pontiac G6

2 Answers

How do you change oil filter


The oil filter is a can shaped object that is screwed into the side of the engine.
You need an oil filter removal tool that wraps a strap around the oil filter so you can unscrew the oil filter in an anti-clockwise direction. When the oil filter is loosened you will get some oil spillage.
When you replace the oil filter, apply a little fresh oil on the rubber o-ring seal before you screw the oil filter back onto the engine. Do not over tighten the oil filter as you can damage the o-ring seal and cause the oil to leak out of the engine when the engine is running.
After installing the new oil filter I suggest you start the engine and let it run until the engine warms up, then check the oil filter to see if there is any oil leaks from the oil filter (between the engine and the oil filter). If it leaks and you have not tighened the oil filter enough then screw the filter a little tighter/

Dec 10, 2011 | 1999 Subaru Legacy

1 Answer

I have replaced the oil pump, cleaned the rods and...


The problem sounds like you did not prime the oil pump before you finished putting everything together. Turn the engine over to were the rotor on distributor is at #1 to fire. Mark the location of distributor base to intake manifold. Pull the distributor out of the intake. With a small pin light look inside the hole and insert a long screw driver into the distributor extensin shaft or use a homemade allenhead wrench welded to a extension rod to turn the pump extension rod. Turn the pump several times until it starts to get hard and the pump will be primed. Turn the distributor extension clockwise to prime pump. Hope this will help you.

May 20, 2010 | Cars & Trucks

1 Answer

Procedures to change engine oil on 1997 Audi A4


the long answer is...put engine flush in oil, run for about 1 hour,switch off/remove key,then remove splash guard from under the engine (best done when car on ramps)then remove oil filler cap and drain plug on sump(oil pan).whilst draining into an empty can with the side cut out(drip tray) locate oil filter and punch a hole in the side of it with a screwdriver,and unscrew it.
Wipe oil onto the rubber seal of the new filter and screw onto carrier.hand tight only.
then replace sump plug washer(copper/fibre)and replace using a 6"long ring spanner and do up tight.
(max pressure of palm of hand)
put in about the same amount of oil that came out,replace oil filler cap and start engine.
check for any leaks,replace splash guard and lower car to level surface,turn off engine,leave for 60 secs,then dip for oil level and top up to midway on dipstick,
job done....
use 10/40 semi synthetic oil.

May 21, 2010 | 1997 Audi A4

2 Answers

What is the part call that the oil filer screws on called. it seems to be leaking from there


Check that the oil filter if firmly screwed onto the engine. If not then drain the oil, undo the oil filter. Wipe the surface of the oil filter connector on the engine so its clean. Get a new oil filter and smear a small amount of oil on the rubber seal. Screw the filter into place making sure it is a tight seal. Re-fill the engine with the right amount of oil. You should be good to go. Check that the oil leak is coming from the filter before you start as it could be something more serious eleswhere like the head.

Nov 09, 2009 | 1999 Ford Taurus

1 Answer

Oil light intermittent, fades, sometimes steady


Check the connection where the wire plugs onto the sender unit. If it's loose, or the wire shorts out to the body, it might flicker. If this isn't the problem, unscrew the sender unit and check your oil pressure using an oil pressure gauge screwed into the same hole. The pressure should be above 40 psi if my mind serves me correct. If it's too low you'll have to replace or check the oil pump. Did you replace the oil filter and oil recently? If the filter is blocked or the oil is old it might also cause the pressure to drop too low.

May 16, 2009 | 2001 Hyundai Elantra

1 Answer

Oil Leak from Spindle


The stud that the oil filter screws onto holds the filter housing to the engine and there is an O ring between the housing and engine that leaks and is common on honda's. Removing the oil filter and then the stud will release the housing and can replace O ring which cost about six dollars at dealer.

Jan 15, 2009 | 1992 Honda Accord

Not finding what you are looking for?
2002 Ford F350 Super Duty DRW Reg. Cab Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...