Question about 2000 Volkswagen Beetle

1 Answer

I need to fix my power window switch, how do i remove the rear door panel, i have removed the 2 screws holding it on the bottom, but it still feels like there are some clips holding it on, and i dont want to break them

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How do i change power window switch on 2001 vw beetle

Posted on Dec 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear door wont open how to take door panel off


you have to remove all door trim screws also remove screws hold manual window handle power window you need to remove power window switch screws.pay attention look for all door panel screws that all holding it in place.

Nov 25, 2012 | 2002 Volkswagen Passat

1 Answer

How do you remove the inside rear door panel of a 2002 ford explorer. I need to service the power window on the rear door on the passenger side. Submitted on 9/29/2009 @ 1:07 pm. Thank you


1. Open window & remove door lock knob. 2. Remove 2 screws from armrest & remove armrest. 3. If manual windows, remove windoe crank. 4. Pry under & remove trim panel around door handle, remove any un-covered screws. 5. This is the fun part, the door panel is affixed with plastic retaining clips, slip something thin under door panel until you can feel where clip is and pull door panel away from door at that point. These clips are suppose to remain in the door panel, but rarely do. They usually remain in the door itself. do this for EVERY clip you find, there are clips approx a foot apart around the entire panel. Good luck. 6. After all retaining clips are pulled out, lift panel slightly to disengage panel from flange at base of window. 7. Disconnect any electric wires or switches and there you have it. Try not to curse.

Sep 29, 2009 | 2002 Ford Explorer

2 Answers

Need to pull door panel off to replace power window motor can not get door panel off


There are 2 screws holding the window switches to the door and 2 screws for the door panel, one is in the pull handle, the other behind the window switches. Remove these screws and using a trim remover(hopefully) work around the sides and bottom of the door to pop the plastic retainers out of the door, push in at the top of the door panel and push up from the bottom to release the top retainer.
There is more to changing the motor than you may think. Steel cover has to be popped off and reused, so be careful.

Jun 08, 2009 | 2003 Chrysler Town & Country

1 Answer

Need to remove drivers door panel


please rate if this helps. Section 01-05: Trim, Interior 1995 Thunderbird, Cougar Workshop Manual REMOVAL AND INSTALLATION The interior trim component Removal and Installation procedures generally apply to all models. If some of the steps do not apply to the particular models being serviced, proceed to the next step. Trim Panels, Door Removal and Installation
  1. ssd~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not pry front door trim panel (23942). Prying on front door trim panel will break the hook retainers.
    Disconnect battery ground cable (14301) .
  1. Carefully pull front door trim panel finish panel (23712) away from front door trim panel .



    9e3f506.gif
Item Part Number Description 1 23713 Front Door Trim Panel Finish Panel 2 17B676 Outside Rear View Mirror Control 3 14028 Door Lock Switch 4 55928-S55 Screw (5 Req'd) 5 14529 Window Regulator Control Switch 6 23942 Front Door Trim Panel
  1. Disconnect wires from front door lock switches (14017), outside rear view mirror controls (17B676) and window regulator control switches (14529) , if equipped; remove front door trim panel finish panel.
  1. Remove front door trim panel retaining screw through front door trim panel finish panel opening.

    Trim Panels, Door


    83b257f.gif


    Item Part Number Description 1 20124 Front Door 2 23942 Front Door Trim Panel 3 383356-S100 Nut (2 Req'd Each Side) 4 56903-S58 Screw (2 Req'd Each Side)
  1. Remove interior lamp lens cover.
  1. Remove screw through interior lamp opening.
  1. Slide front door trim panel upward to disengage hooks.
  1. Rotate top of front door trim panel away from front door (20125) , and lift bottom hooks from front door.
  1. Disconnect window regulator jumper wire (14A630) .
  1. Remove front door trim panel.
  1. To install, reverse Removal procedure.

May 07, 2009 | 1994 Mercury Cougar

1 Answer

Replace pwer mirror driver side 2002 ford explorer


remove the door panel with out breaking the hook style plastic clips by un doing any phillip screws holding the doors pull handle, and maybe a couple of lower retainer screws, remove the power window and power lock switchs from the doors handle than pull lightly on the bottom of the door panel . if it feels loose it should pull out about 2 inches.than slide the whole door panel straight up and off the door it self. now you can unclip the power mirror wire connector and remove the mirror itself from the upper corner of the door
good luck chris

Mar 22, 2009 | 1997 Ford Expedition

1 Answer

Procedure for removing door panel on passenger side 1994 camry


Sure.

Pull off the triangle thing.
On the door, at the front edge, there should be 2 plastic caps. Remove them. Under the caps there are screws. Remove them.
On the rear of the door panel, above the latch, are 2 round things, with a smaller round thing in the middle. Press on the inner round thing, and pull the pin assemblys out.
Do you have a light on the door panel at the bottom? If so, pry it out with a small screwdriver (it's just a "press-fit"), and remove the wire connector.
Under the arm-rest, remove the big phillips screw that is hidden, about an inch back from the outer edge of the panel. You will see the hole.
Under the arm rest, remove the tiny plastic trim cover, remove another big phillips screw.
Remove the door handle: Remove the phillips screw. Slide the handle forward or backward to release it from the door metal. Undo the clamp from the lock rod to the handle.
Remove any screws at the very bottom of the panel, if there are any.
Starting at the bottom of the panel. pull straight out, to defeat the plastic clamps tht holds the panel to the door metal. Once the panel is loose, pull it up a bit to remove it from the window opening retainer. Finally, inside the panel, unplug the wiring harness to the window switch assembly.

If you need any more info, please comment back. And, Thanks for the FIxYa.

Nov 14, 2008 | 1994 Toyota Camry

1 Answer

Remove right rear door panel


  1. Remove the rear door power window/power door lock switch
  2. Remove the door handle bezel. Remove the door trim panel screw located behind the door handle bezel.
  3. Remove the door trim panel screws located by the armrest handle.
  4. Remove the door trim panel using J 38778.
  5. Disconnect the electrical connectors.
  6. Remove the door trim panel from the door.
INSTALLATION PROCEDURE

IMPORTANT: Discard the old door trim panel retainers and replace with new retainers before installing the trim panel

  1. Install new trim panel retainers to the rear door trim panel.
  2. Connect the electrical connectors.
  3. Align the door trim panel retainers to the door.
  4. Press the door trim panel at the retainer locations until the retainers are fully seated.
  5. Install the trim panel screws. Tighten Tighten the door trim panel screws to 2 N.m(18 lb in) .
  6. Install the power window/power door lock switch


Nov 04, 2008 | 1998 Oldsmobile Intrigue

1 Answer

Broken power window mechanism in the drivers door, on a 1993 Toyota Camry. How do you get the inside door panel off?


Remove the plastic screw covers at the forward edge of the door. Remove the 2 gold coloured screws.
Using a flat blade screwdriver, insert the blade above & below the locking thing at the door handle, pry up and down, top & bottom respectively. Slide & pull the handle out, remove the rod going to the handle.
Remove the 2 big screws for the door panel. 1 is under a small trim cover, the other is under the armrest
Remove the lower light & unplug it (if you have one) which may be under the arm rest (it pops out)
Press the centers of the 2 round push clips that are on the rear edge of the door panel and pull the clips out
Remove any screws at the bottom of the door panel (if you have them)
Starting at the bottom of the panel pull straight out with steady, even pressure as to not snap the plastic clips. After the bottom & side clips are disconnected from the door, lift the top of the panel straight up.
Remove the plastic sheet that covers the inner shell of the door.
Uning a 10 millimeter socket, remove the bolts that holds the window onto the regulator
Remove the window, up & out thru the top of the door
Unbolt & replace the regulator.

Sep 16, 2008 | Toyota Camry Cars & Trucks

1 Answer

Rh door panel


1. Remove the philips screw in the plastic trim by the mirror and remove the trim piece.
2. Using a flat blade screw driver gently pry up the front of the panel holding the window and door lock switches. This pulls the assembly out of the spring clamp. Pull it up and forward to remove it from the arm rest.
3. Remove the two philips screws holding the switches to the trim piece.
4. Find the two screws holding the arm rest. They're at the junction of the arm rest and the switch assembly. Only the one going into the door needs to be removed.
5. Gently pry the trim piece from the door handle. There are two spring clamps, one in the front and one in the rear of this plastic piece.
6. There is a hidden phillips screw that needs to be removed. It's located at the inside bottom rear corner of the door panel. It's hidden in the carpet trim.

After this last screw is removed the door panel can be lifted straight up and off. Feed the cable harness through the hole and your're done.

Jul 12, 2008 | 1992 Ford Thunderbird

Not finding what you are looking for?
2000 Volkswagen Beetle Logo

533 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...