Question about 2003 Ford Crown Victoria

2 Answers

Hvac blower not operating any speed,

Hvac blower not operating,blend doors operational can jump power to motor it will run hvac control head apears ok, this is and 03 crown vic with ATC

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 145 Answers

Have you tried replacing the blower resister module?

Posted on Oct 01, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Have you checked Fuse F1.103 40Amp in the Battery Junction Box? You also have the Blower Motor Relay located in the BJB which is feed from the Function Selector Switch

Posted on Oct 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blower fan not working at all 2004 Buick rendezvous


Which system ?
HVAC Systems - Manual HVAC Systems - Automatic
If automatic it's probably the blower motor control processor .
Blower Motor Control Processor The blower motor control processor is an interface between the HVAC control module and the blower motor. The blower motor speed control, Blower motor speed signal, battery positive voltage and ground circuits enable the control processor to operate. The HVAC control module sends the commanded blower motor speed to the control processor through a 0 to 12-volt linear ramped blower motor speed control circuit. As the blower motor speed control voltage increases, the blower motor speed increases. The control processor sends the actual blower speed to the control module through a 0 to 12-volt blower motor speed signal circuit. The processor supplies 12volts to the blower motor through the blower motor voltage supply circuit. The control processor uses the blower motor ground as a low side control to adjust the blower motor speed.

Nov 19, 2016 | Buick Cars & Trucks

1 Answer

Heater fan runs when heater is off.06 ford expoler


Automatic or manual climate control ?
  • The blower motor does not operate correctly - manual climate control
  • Circuitry short
  • A/C blower motor resistor
  • A/C blower motor switch
  • Blower motor high speed relay
  • Go To Pinpoint Test O .

  • The blower motor does not operate correctly - EATC
  • Circuitry short/open
  • A/C blower motor speed control
  • EATC module
  • Go To Pinpoint Test Q .

Pinpoint Test Q: The Blower Motor Does Not Operate Correctly - EATC
Normal Operation Under normal operation, the blower motor control module receives a 1-2 volt signal from the EATC module through circuit CH218 (GN/VT) to determine the desired blower motor speed. The EATC module receives a feedback voltage from the blower motor control module through circuit VH219 (GY) to determine actual blower motor speed. When the highest blower motor setting is selected, the EATC module sends 12 volts to the blower control module through circuit CH217 (BN).
    Possible Causes
  • An open, short to voltage, ground or together in circuits CH218 (GN/VT), VH219 (GY) or circuit CH217 (BN)
  • Blower motor control module
  • EATC module
  • If automatic HVAC system i would suspect Blower motor control module .

Oct 27, 2016 | 2006 Ford Explorer

3 Answers

1999 ford expedition , runs good doesn't overheat , but puts out no heat ?


heater core might need replaced . check the hoses going to it under the hood after it gets to operating temperature .One should be hot and the other not so much

Nov 19, 2015 | Ford Cars & Trucks

2 Answers

What causes a/c to blows cold on driver's side and hot on passenger side ?


There is a little motor on the heater box under the dash that needs to be replaced. It's called a blend door actuator...

Mar 16, 2015 | 2004 Cadillac DeVille DHS

1 Answer

Blower motor not working on 2005 buick lacrosse cxl


Blower operation is handled by the HVAC control module which gets its power from the 10A HVAC fuse in the instrument panel fuse block. There is a blower motor control processor that gets its power from the 30A BATT MAIN 4 fuse in the underhood fuse block. The HVAC control module sends speed signals to the blower motor control processor which turns on the blower motor at the selected speed. Note that there is no relay involved. If you check the fuses and check the path to the blower motor you may find that the motor is OK and the trouble is somewhere else

Oct 15, 2012 | 2005 Buick LaCrosse

1 Answer

Blower stays on after key is removed, now a/c works in front once I hit the highway.


Which of these systems does your vehicle have ?
HVAC Systems - Automatic
Blower Motor Control Processor
The blower motor control processor controls the speed of the blower motor by increasing or decreasing the voltage drop on the ground side of the blower motor. The HVAC control module provides a voltage signal to the blower motor control processor over the blower motor speed control circuit. As the requested blower speed increases, the HVAC control module increases the amount of time that the speed signal is modulated to ground. As the requested blower speed decreases, the HVAC control module decreases the amount of time that the signal is modulated to ground.

HVAC Systems - Manual
Air Speed - Front Control
The blower motor forces outside air into the vehicle's interior. The vehicle operator determines the blower motor's speed when the driver places the blower switch in one of 5 blower speeds. The blower motor will always operate in any switch position other than OFF, as long as the ignition switch is in the RUN position. The blower motor and mode switches are located within the HVAC control module. The blower motor OFF input is connected in series with the HVAC control module by the off blower motor control circuit.
Depending upon the selected speed, power is provided to the blower motor from either the ignition 3 voltage or battery positive voltage circuits from the fuse block. The battery positive voltage circuit only provides power when the High blower switch position is selected. Power and ground are provided to the HVAC control module by the ignition 3 voltage and the ground circuits.
Low Blower Speed
When the Low 1 blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the low blower motor control circuit. Voltage is divided between 4 series resistors, a blower relay, and the blower motor to achieve the desired blower speed. The blower motor is grounded through the ground circuit.
Medium Blower Speeds
When the Medium 1 blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the medium 1 blower motor control circuit. Voltage is divided between 3 series resistors, a blower relay, and the blower motor to achieve the desired blower speed. The blower motor is grounded through the ground circuit.
When the Medium 2 blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the medium 2 blower motor control circuit. Voltage is divided between 2 series resistors, a blower relay, and the blower motor to achieve the desired blower speed. The blower motor is grounded through the ground circuit.
When the Medium 3 blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the medium 3 blower motor control circuit. Voltage is divided between a series resistor, a blower relay, and the blower motor to achieve the desired blower speed. The blower motor is grounded through the ground circuit.
High Blower Speed
When the High blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the high blower motor control circuit. The voltage energizes the blower relay, causing the blower motor to be connected directly to the battery positive voltage circuit. The blower motor and blower motor relay are grounded through the ground circuit.

HVAC Control Module
The HVAC control module is a class 2 device that interfaces between the operator and the HVAC system to maintain air temperature and distribution settings. The battery positive voltage circuit provides power that the control module uses for keep alive memory (KAM). If the battery positive voltage circuit loses power, all HVAC DTCs and settings will be erased from KAM. The body control module (BCM), which is the vehicle mode master, provides a device on signal. The control module supports the following features:

Feb 09, 2018 | 2005 Chevrolet Tahoe

1 Answer

1996 buick riviera heater blower won't run. I jumped the motor and it runs. Turn on the switch and it won't run


you have a piece of solder broken off the controller of your hvac unit, causing power not to get to the blower motor it self. take test light and see if you have power at the blower motor. check and see if you have continuty or brake between the power wire at the blower motor and at the hvac control unit. if wires are good then the problem will lie in the hvac control unit. check and see if the blower is working at all speeds, if it works on some speeds thens the blower motor resistor.

Sep 29, 2011 | 1996 Buick Riviera

2 Answers

Blend door for front temp control is stuck in the 'cold' position this winter. Is there a way to manually move and fix the door to get some heat?


you have to replace the blend (heat/cold) door motor, you can try to remove motor and turn door and try to jam something in door handle slot ,that the part that the motor turns,hope this helps.

Dec 26, 2009 | 2001 Ford Windstar

1 Answer

MY HVAC fan stopped blowing. Checked all the


Check the blower motor speed control resistor pack is ok.
(The resistor pack is usually located in the blower fan ducting in the air flow).
Check condition of electrical connection terminals on the blower motor circuit - these terminals pass considerable current and over time may fatigue overheat and loosen.
Check operation/replace any blower motor control relay,
Check the blower motor will run if +12v directly applied to the blower motor.
Check operation of the blower motor speed control switch is ok.

Oct 08, 2009 | 2003 GMC Sierra

Not finding what you are looking for?
2003 Ford Crown Victoria Logo

573 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...