Question about 2001 Hyundai Tiburon

1 Answer

Windshield wipers became sluggish, then stopped mid-swipe. I'm assuming the motor died or the linkage seized. How is the motor/linkage assembly accessed?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,280 Answers

Take/Tow your vehicle to an authorized Hyundai dealership and pay the diagnostic fee... they will tell you exactly what the problem is and the cost of parts/labor to fix it... at least this way you'll know what the problem is and what's required to fix it. OR,
Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Wiper motor


Possible wiper linkage has broken/seperated from wiper motor. The wiper cowling covering the linkage assembly will need to be removed to inspect/repair

Feb 13, 2016 | 2008 Chevrolet Impala

1 Answer

2007 Pontiac g6 wipers stay in upright position


Hey Derek , here is how the wipers park position is suppose to work !
Windshield wiper motor park operation is controlled by the body control module (BCM) using an input from the park switch within the wiper motor assembly. The BCM monitors the windshield wiper motor park switch circuit to determine if the windshield wiper blades are at the bottom of the glass. The circuit will be pulled to ground by the wiper motor park switch while the windshield wiper motor is operating. When the wiper switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the BCM will continue to operate the motor until the wipers reach the park position. If the ignition is turned OFF while the wipers are in mid-cycle, the wipers will stop immediately where they are. The BCM will park the wipers the next time the ignition is turned ON.
The wipers will not park when they are commanded ON and OFF with a scan tool. The BCM will park the wipers the next time the wiper switch is turned ON and OFF.
The BCM provides stall protection for the wiper motor by monitoring the park switch. If the park switch does not transition for 3 seconds while the wipers are operating, the BCM will assume that the wiper motor is stalled, and will de-energize the wiper relay until the wiper switch is cycled OFF and ON again.
Check for a voltage signal on the yellow wire at the wiper motor assembly , this is signal to the BCM ! If there is no signal you need to replace the windshield wiper motor assembly ? If there is a signal need to have Tech 2 scan tool hooked up to see if The BCM is the problem ! Relay #39 an #40 are the high an low wiper relays in the under hood fuse block ! Do you have a volt meter ,do you know how to do electrical testing ?

Sep 21, 2015 | Pontiac Cars & Trucks

3 Answers

My windshield wipers wont work.


It Sounds Like, Either The Arms Are Loose ,If You Can Hear Something Moving Behind The Dash,
Or The Linkages Are Seized ,If The Motor Just Hums No Movement Heard,In Which Case Try Spraying Q 20 On The Linkage And Try Moving The Wiper Arms By Hand To Get It Going Again,
If Not The Motor May Just Be Burn;t Out.

Mar 16, 2013 | Cars & Trucks

1 Answer

Kia Sorento 2007:My windshield wiper stops on wrong side, what can I do?'.


If the wipers are consistent in where they stop the problem may be due to the splined shaft of the drive motor has rotated within wiper linkage attachment. Remove motor/linkage assembly remove linkage from motor and check for stripped splines on the linkage/motor. Willie

Jan 04, 2013 | 2007 Kia Sorento 4x4

1 Answer

2000 HYUNDAI ACCENT, problem is the Windshield Wiper operation is malfunctioning, in the Delay mode, and in the off position, Windshield Wiper arms/blades stop at the half point on the Windshield glas


The park position is controlled inside the motor/actuator assembly. Not sure if it can be repaired. See if it is assembled with screws versus rivets. A new assembly is less than $100.

Jul 05, 2017 | 2000 Hyundai Accent

1 Answer

How do I remove the windshield wiper motor from a Ford F-250?


2002 Ford F-250 Windshield Wiper Motor Removal & Installation 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFF position to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.

Nov 09, 2009 | 2002 Ford E250

2 Answers

Windshield wipers don't work right. Try to and quit mid cycle.


YOUR WIPER MOTOR COULD HAVE BINDING LINKAGE AND PIVOTS.TRY LUBRICATE THEM WITH WD40.TRY NOT TO GET ANY ON WINDSHIELD.IF THIS DONT WORK WIPER MOTOR COULD BE FAULTY.

Sep 27, 2009 | 1996 Acura TL Series

1 Answer

Windshield wipers stopped working on 1998 Nissan Sentra. Is it a fuse problem? If so, where is fuse box and which fuse? Is it a motor problem? is this an easy diy fix?


Water can enter and displace the grease in the wiper arm linkage ball joint where the wiper linkage attaches to the wiper motor linkage.

This can result in gradual wear over a period of time inside the joint that could lead to the separation of the wiper linkage assembly from the wiper motor linkage at the ball joint. A loss of windshield wiper function can result when this separation occurs.

To prevent grease from being washed out of the joint, the dealers will modify by adding a water diversion seal that will prevent water from entering the windshield wiper linkage ball joint area.

Jun 13, 2009 | 1998 Nissan Sentra

1 Answer

1989 Ford F150 windshield wipers not stopping


Sounds like the wiper blade motor is going bad. You can also try to use some alpurpose oil on it

Feb 07, 2009 | 1989 Ford F 150

Not finding what you are looking for?
2001 Hyundai Tiburon Logo

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...