Question about 2001 Kia Sportage

1 Answer

How do i get the crankshaft pulley back in place after the timing belt broke

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 92 Answers

Make sure you line the pulley up w/ the keyway, push it straight on as much as you can by hand (can grease the shaft and inside pulley first if you want), then insert the long bolt and crank it down the rest of the way to get the pulley the rest of the way on. an air gun is very useful for this bolt if you have access.

Posted on Sep 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you put a timing belt back in time after it broke?


Well, hopefully the valves were not damaged when the belt broke, If no valve damage was done, get the engine/crankshaft to top dead center, line up camshaft sprocket to timing mark and install belt around pulleys, gears, replace water pump if needed, tension belt if no automatic tensioner is used, try to start to see if it runs and hopefully it will. Might be time for an engine if valve damage was done.

Jul 14, 2014 | 1992 Chrysler Lebaron

1 Answer

I need a fan belt diagram for a 1994 bighorn


Timing belt installation

1. Ensure locking bolts located correctly [4] & [5] in the picture below:

tdisline_32.jpg
CS = Crankshaft
CA = Camshaft
IP = Injection Pump

2. Ensure timing marks aligned [10].
3. Fit timing belt in clockwise direction, starting at crankshaft sprocket.

NOTE: "ISUZU" lettering on belt should be readable from front of engine.

4. Slacken tensioner pulley bolt [9]. Push tensioner pulley against belt.
5. Ensure belt is taut between injection pump sprocket and tensioner pulley as well as crankshaft sprocket and camshaft sprocket.
6. Position tensioner lever [8] against tensioner pulley housing.
7. Remove locking bolts from sprockets [4] & [5].
8. Apply a load of 10 ... 12 kg to tensioner lever. Use spring balance [11].
9. Tighten tensioner pulley bolt to 80 Nm.
10. Turn crankshaft slowly 45 degrees anti-clockwise. Use spring balance to tension belt.
11. Repeat tensioning procedure at 45 degrees intervals for one anti-clockwise turn of the crankshaft.

NOTE: DO NOT turn crankshaft clockwise during tensioning procedure!

12. Fit tensioner lever to original position. Tighten nuts [12].
13. Install: Injection Pump flange [6], Camshaft sprocket flange [7], and water pump pulley.
14. Install components in reverse order of removal & refill coolant.
tdisline_33.jpg
Hope that helps. and good luck out there in the country side.

Apr 08, 2012 | Cars & Trucks

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

1 Answer

How to do timing belt on 2004 foerd focus



Remove Your Timing Belt

1Disengage the negative battery cable in all models.

2Detach the passenger inner splash-shield and wheel cover, the accessory drive and timing belts, the tensioner and the crankshaft pulley.

3Remove the spark plugs, catalytic converter and idler pulley in 2000 and older Ford Focuses. These models also require the crankshaft be turned to "Top Dead Center" (TOC) and a crankshaft timing peg be inserted. Turn the shaft to the right against the timing peg.

4Undo the retaining fasteners and lift the timing belt cover off the engine. Align the crank and camshaft timing marks. Older models call for undoing the water pump pulley and valve cover before locking the camshaft in place.

5Release the tensioner's bolt. Turn the arm to the right 14 degrees and place a 1/8 inch drill bit in the opening. This secures the belt tensioner in place.

6Take the timing belt off.
Install Your Timing Belt

1Replace the timing belt counterclockwise motion beginning at the crankshaft.

2Unlock the tensioner. Recheck the timing marks by turning the crankshaft two rotations to the right.

3Tauten the tensioner's pulley bolt to 15 to 22 foot pounds (20 to 30 Nm) in 2003 and younger models and to 17 to 20 foot pounds (22 to 28 Nm) in older Focuses. Remove the crankshaft timing peg. Reconnect the crankshaft pulley and secure to 81 to 96 foot pounds (110 to 130 Nm) and 81 to 89 foot pounds (110 to 120 Nm) respectively.

4Replace the splash shield, front wheel, timing belt cover, accessory drive belt and tensioner and any other items that were disconnected.

5Hook up the negative battery cable. Start the engine and check that the timing belt is functioning properly.

Nov 18, 2010 | 2004 Ford Focus

1 Answer

Do not know how to remove crankshaft pulley to replace timeing belt


Ignore smart a$$ comments.
Disconnect negative battery terminal.
Remove front right wheel.
Remove splash guard.
Place jack under engine.
Remove left engine support bolts from body.
Remove engine support plate bolts from engine.
Unbolt air conditioner pump and move it out of the way.
Get under vehicle and remove steering pump bolts and move it out of the way.
Remove 6 crankshaft pulley bolts, should be 12mm.
The engine support bracket shoud come off now.
Remove the main crankshaft bolt.
Remove crankshaft dampener.
Remove the timing cover bolts and take off the covers.
Take off the old belt & replace with a new one, don't use a previously used belt.
Make sure the belt tensioner is installed correctly.
Put all the stuff back on.
Get a Haynes manual, pages 3-41.

Apr 30, 2009 | Plymouth Voyager Cars & Trucks

2 Answers

Timing belt alignment


A factory service manual would help, but I'm assuming that if you had one, you probably wouldn't be on this site.

To set the timing, you need to first perform the obvious: remove the accessory drive belts, cam pulley covers, and engine fan and hub. Next you'll need to rotate the engine by hand until the timing marks on the camshaft sprockets and crankshaft are aligned with their corresponding stationary marks. The 0 degree mark on the lower timing belt cover is the timing mark for the crankshaft pulley. There is a mark (small, vertical formed indentation) for the left camshaft pulley on the backing plate behind the pulley near the 1 o` clock position. The same mark exists for the right camshaft pulley only it is on the backing plate near the 8 o`clock position (making it difficult to see). With the crankshaft placed at the zero mark, you can observed where the timing discrepancy exists.

(TIP: Once the right camshaft timing is properly lined up, etch an additional mark on the pulley's face and the backing plate at the 12 o`clock position. This will make it easier to align the pulley for furture adjustments and repairs)

To set the timing correctly, move the crankshaft pulley to 12 deg. BTDC. Being careful to not disturb the position of the crankshaft once it has been moved to that position, remove the crankshaft pulley, lower timing belt cover, timing belt tensioner, and timing belt. Compress the timing belt tensioner and if the original ring pin isn't available to retain the tensioner a small allen wrench can be used to achieve the same results. Line up both camshaft marks and reinstall the timing belt and timing belt tensioner (do not remove the timing belt tensioner tool used to maintain the tensioner piston in a compressed position). When installing the timing belt, be sure to allow the least amount of slack to exisit between the left camshaft pulley and the crankshaft sprocket, but without moving the pulleys.

Next, remove the timing belt tensioner piston retention tool and mount the lower timing belt cover and crankshaft pulley (without fully installing them). Rotate the crankshaft pulley to the 0 deg. mark. If done correctly, moving the crankshaft pulley from 12 deg. BTDC to 0 deg. will remove all remaining slack from the timing belt assembly and the camshaft pulleys and crankshaft pulleys will be lined up with their corresponding marks. Once proper timing has been achieved, install all removed parts.

(Another TIP: I hope it's not necessary, but in case it is, I'll remind you that proper torque of all bolts are necessary as this is an all aluminum engine. Stripping out bolts holes due to over-tightening bolts occurs very easily and become very annoying to deal with [e.g. alternator belts not being able to be tightened completely and constantly squealing every few days, etc.])

Apr 26, 2009 | 1997 Isuzu Rodeo

1 Answer

My timing belt broke on my '99 Ford Escort ZX2. Please tell my husband how to replace it. Than k you



 
 
Timing Belt
REMOVAL & INSTALLATION
1.8L Engine
Disconnect the negative battery cable.
Remove the timing belt covers.
Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
Remove the crankshaft pulley and hub.
If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
Install the timing belt.
Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.
Fig. 1: Timing marks are located on the camshaft pulleys as shown — 1.8L engines


 
Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned — 1.8L engines


 
Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position — 1.8L engines


 
Fig. 4: Check the timing belt deflection at the location shown — 1.8L engines

Mar 28, 2009 | 1999 Ford Escort

3 Answers

Need a timing scamatic for a 1998 ford contour 16v Zetec ct 2.0l


Installation
All Vehicles
  1. NOTE: Rotate the crankshaft clockwise.
    Rotate the crankshaft to TDC on cylinder No. 1.
6d7ac03.gif
NOTE: Cylinders No. 1 and No. 4 are at TDC when the Woodruff key points straight up.
Remove the blanking plug, completely screw in the special tool and auto-align the crankshaft to TDC.

0889b40.gif
  1. Position cylinder No. 4 to valves overlap" and install the special tool.
  2. Hold the camshafts by the hexagon using an open-ended wrench and turn them in the direction of engine rotation.
  3. Slide the special tool onto the ends of both camshafts.
6971087.gif
swp~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not kink the timing belt (do not bend the timing belt less than a diameter of 35 mm).
swp~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not rotate the crankshaft; as necessary check that it is still resting against the timing pin.
NOTE: Design with lower idler pulley shown (built up to 06/1999).
NOTE: The lug of the belt tensioner should not be hooked in the sheet metal cover during timing belt installation.
Position a new timing belt in place.
  • Starting from the crankshaft timing belt pulley and working counterclockwise, position the timing belt in place while keeping it under tension.

2907f65.gif
  1. swp~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not rotate the crankshaft; as necessary check that it is still resting against the timing pin.
    NOTE: Design without lower idler pulley shown (built 06/1999 onwards).
    NOTE: The lug of the belt tensioner should not be hooked in the sheet metal cover during timing belt installation.
    Position a new timing belt in place.
    • Starting from the crankshaft timing belt pulley and working counterclockwise, position the timing belt in place while keeping it under tension.
143871c.gif
  1. NOTE: Incorrect timing belt tension will cause incorrect valve timing.
  2. Pre tension the timing belt.
  3. Rotate the tensioner locating tab counterclockwise and insert the locating tab into the slot in the rear timing cover.
  4. Position the hex key slot in the tensioner adjusting washer to the 4 o'clock position.
  5. Tighten the attaching bold enough to seat the tensioner firmly against the rear timing cover, but still allow the tensioner adjusting washer to be rotated using a 6mm hex key.
0afbc96.gif
CAUTION: Tension the timing belt, working counterclockwise. Using the hex key, rotate the adjusting washer counterclockwise until the notch in the pointer is centered over the index line on the locating tab (the pointer will move clockwise during adjustment).

4e30913.gif
While holding the adjusting washer in position, tighten the bolt
NOTE: Hold the intake timing belt pulley with special tool to stop it from turning.
Tighten the timing belt pulleys.
  1. Tighten the intake camshaft timing belt pulley bolt.
  2. NOTE: Hold the exhaust camshaft by the hexagon with an open-ended wrench to stop it from turning.
    Tighten the exhaust camshaft timing belt pulley bolt.
  3. Remove the special tool.
    • Install the blanking plug.
  4. Remove the special tool.
  5. NOTE: Hold the camshaft by the hexagon with an open-ended wrench to stop it from turning.
    Tighten the exhaust camshaft to stage 2.
    1. NOTE: Turn the crankshaft two revolutions in the normal direction of rotation.
      Check the valve timing by inserting the special tool. Correct it, if necessary.
      • Screw in special tool 303-574 and make sure that the crankshaft is touching it.
      • Insert special tool 303-465 into the camshafts; if necessary loosen the timing pulleys and correct the camshaft alignment.
      • Detach the special tools.
    1. NOTE: Use a new blanking plug.
      Install the blanking plug on the exhaust camshaft pulley.

Mar 10, 2009 | 1998 Ford Contour

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

4 Answers

1999 Plymouth Breeze 2.0 SOHC I just replaced the timing belt because the old one had not broke but rather had eaten off all the teeth so the timing was off. I set the timing mark on the crank to TDC...


When changing the timing belt you need to place the cam shaft a TDC( clock wise), then rotate the crankshaft to TDC (clockwise), then back off the crankshaft (counter clockwise) THREE TEETH then back (clockwise) 1/2 tooth before TDC place your timing belt arround the crankshaft- water pump- and camshaft finally putting arround the tensioner pulley, holding 25 flbs of torque on the tensioner pulley to get the correct tension then push up on the hydrolic tensioner and tighten and you should have it.... rotate the crankshaft twice, if the camshaft pulley ends back on TDC then you have it correct.

Nov 29, 2008 | Plymouth Breeze Cars & Trucks

Not finding what you are looking for?

Open Questions:

See all 2001 Kia Sportage Questions

2001 Kia Sportage Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...