Question about 2003 Ford Ranger Regular Cab

2 Answers

My brake pedals go to the floor. I was putting rotors on and did not have the caliper hooked up on the one side and I pushed in brake pedal then fluid came pouring out of piston and piston popped off. (the piston of the caliper that was not hooked up) What now? Bleed the lines?...

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,982 Answers

OOPS!!! yes, bleed lines and it should be fine.

Posted on Sep 29, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,187 Answers

Yes, you must re-assemble the wheel cylinder and bleed the system.
Thre is a bleeder valve on top of the wheel cylinder. Open it up and allow the fluid to gravity feed as you replenish the master cylinder reservoir.
You will probably need an assistant to help do the last of the bleeding.

Posted on Sep 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Why does 02 Mazda Tribute front passenger brake keep locking up?


Try bleeding some brake fluid on that side. You may have a blockage. Also check if the rotor is in good condition, it may be warped. Good luck!

Feb 11, 2017 | 2002 Mazda Tribute

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

1997 Jeep Grand Cherokee Brake Problem. Brake Pedal Falls To The Floor. Calipers were replaced twice,master cylinder,brake hoses and pads. Systemm has been bleed numerous times - no air but the brake...


This may sound dum but its been done a few times and is a simple mistake , the bleeder screw is up top, with the caliper on the bleeder screw should be up top, if not then calipers are on the wrong side, it sounds like air in the system, also you pumped the pedal up to push out the piston so pads hit rotor after bleeding,i dont see anything else, if the pedal is good with pinched lines at caliper then it got to be calipers are wrong or on the wrong side and the bleeder is not atop caliper,also you bleed the rear also? these trucks and cars use left caliper and rt rear on one system of the master and rt front and left rear on one side, let me know about the caliper, heres a picture to show you what i mean. hope this helpsjohnjohn2_23.jpg

Nov 16, 2010 | 1997 Jeep Grand Cherokee

1 Answer

Spongy brakes


So long as the brake booster is working, test it by turning on the engine, press the brake pedal all the way down, then shut off engine keeping your foot on the brake pedal, if the pedal comes up slightly pushing against your foot then the booster IS working.

Did you BLEED the brakes??????

Mar 29, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Pistons in both front calipers stay out, both calipers replaced


You may have a leak in the booster or master cylinder. You can put a pressure tester on the system to test for leaks. It does sound like you have an air leak.
You can try to bleed the master cylinder, then slave cylinder, then brake lines.

Aug 24, 2009 | 1993 Oldsmobile Achieva

2 Answers

Putting new brake pads on front,removed two bolts but caliper won't come off,will slide around


U will probably have to push the calipre piston into the calapre and little.With a screwdriver put between brake pad and rotor and pull sideways this should push the calipre in far enough

Aug 06, 2009 | 1998 Chevrolet Malibu

2 Answers

Brake pedel pushes to the floor


pump the pedal about 10 times and see if it comes back up, u need to pump the caliper pistons out after a brake job.

Jun 27, 2009 | 1997 Ford F150 Regular Cab

2 Answers

Changed front brake pads. brake pedal goes to floor. no brakes


Something doesn't sound right, you shouldn't have to remove the brake line to install pads. Did you have to do this on both sides? Do the new pads and the old pads look the same? Did you get the caliper on crooked? Just recheck your work first before replacing more parts. When you install the caliper, You have to hook the pad on one side first before you slide it over the rotor.

Mar 26, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Brakes


All you have to do is take the calipers off crack open the bleeder of the side you are working on leave the old pad in the caliper and press the pad in as far as it will go tighten bleeder clean the rotors with brake clean to get the oily substance off they put on during shipping to keep them from rusting put rotor back in place and put new pads in caliper if they give you grease for the caliper sliders put some on the caliper bolts and sliders the thing the bolts go into on the caliper so they move fairly easy this way your brakes will work better and last longer put caliper back in place tighten caliper bolts snug usually with a ratchet like a good 3/8 ratchet then do the other side fill up the master cylinder with proper brake fluid usually dot3 but should say on master cylinder cap bleed brakes if you did just the front bleed the passenger side first pump pedal a few times dont go all the way to the floor have someone open the bleeder on the right front passenger front while holding pedal down with just a little pressure one foot on pedal one under pedal so it dont go to the floor then do the same for the other side check fluid start vehicle if pedal is good go for a test drive and thats it.

Jan 06, 2009 | 2005 Ford F-150

Not finding what you are looking for?
2003 Ford Ranger Regular Cab Logo

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...