Question about 1993 Ford Aerostar Extended

2 Answers

My van syarts but as soon as i put it in gear it stalls. i changed the destributer and checked the neutral safety switch and neither worked what do i do next????

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Did you check your fuel filter?

Posted on Jan 22, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

If it drives and clears up after you get too a certain speed it is the torque converter selinoid

Posted on Dec 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Caravan won't start cold unless I rev engine for 5 min


You need to check the cold choke set up, which may be called a IAC
Idle Automatic Control this is sensor works the am starts for cold or hot idles...
Do you have a light on??

Oct 23, 2013 | Dodge Caravan Cars & Trucks

1 Answer

2000 ford windstar won't start after changing safety neutral switch?


You need to adjust the Switch, it thinks you are in Gear

Apr 09, 2013 | 2000 Ford Windstar

1 Answer

My car stalls when it is put into drive or reverse and the other two gears


Someone would need to check the neutral safety switch on the transmission.

Oct 12, 2012 | Hyundai Motor 1996 Elantra

1 Answer

2003dodge caravan neutral safty switch


Test/Service/Replace Neutral Safety Switch
Most neutral safety switches are combinations of a neutral safety switch and a backup lamp switch. Others have separate units for these two distinct functions. When the reverse light switch is not part of the neutral safety switch, it seldom needs adjustment, as it is directly activated by the transmission or the gear selector linkage.
f_ttat_t3.20.jpg Typical location of a neutral safety switch on a transaxle. Reprinted with permission of Ford Motor Company. A neutral safety switch allows current to pass from the starter switch to the starter when the lever is placed in the P or N position. Some neutral safety switches are nonadjustable. If these prevent starting in the P or N position and the gear selector linkage is correctly adjusted, they should be replaced.
To adjust a typical neutral safety switch:
  • Place the shift lever in neutral.
  • Loosen the attaching bolts for the switch.
  • Using the angling pin, move the switch until the pin falls into the hole in its rotor.
  • Tighten the attaching bolts.
  • Recheck the switch for continuity. If no voltage is present, replace the switch.
  • The switch sometimes controls the operation of the back-up lights also. With the engine off and the key on, put the selector in reverse position. Check the back-up lights to see that they are on. Then, check in the drive position to see that they are out.

Aug 15, 2012 | Cars & Trucks

1 Answer

Where is neutral switch on a 92 dodge caravan


Safety Switch Most neutral safety switches are combinations of a neutral safety switch and a backup lamp switch. Others have separate units for these two distinct functions. When the reverse light switch is not part of the neutral safety switch, it seldom needs adjustment, as it is directly activated by the transmission or the gear selector linkage.
f_ttat_t3.20.jpg Typical location of a neutral safety switch on a transaxle. Reprinted with permission of Ford Motor Company. A neutral safety switch allows current to pass from the starter switch to the starter when the lever is placed in the P or N position. Some neutral safety switches are nonadjustable. If these prevent starting in the P or N position and the gear selector linkage is correctly adjusted, they should be replaced.
To adjust a typical neutral safety switch:
  • Place the shift lever in neutral.
  • Loosen the attaching bolts for the switch.
  • Using the angling pin, move the switch until the pin falls into the hole in its rotor.
  • Tighten the attaching bolts.
  • Recheck the switch for continuity. If no voltage is present, replace the switch.
  • The switch sometimes controls the operation of the back-up lights also. With the engine off and the key on, put the selector in reverse position. Check the back-up lights to see that they are on. Then, check in the drive position to see that they are out.

May 10, 2012 | 1992 Dodge Caravan

1 Answer

Cant push the button to put in gear


CHECK MAKE SURE BATTERY FULLY CHARGED IT HAS TO BE 12.5 VOLTS BEFORE THE BRAKE TRANSMISSION SHIFT INTERLOCK SOLENOID WORKS.IF BATTERY POWER GOOD CHECK BRAKE LIGHTS TO SEE IF BRAKE LIGHTS SWITCH IS WORKING.IF NO CHECK FUSE.IF FUSE GOOD BRAKE LIGHT SWITCH IS FAULTY. IT CONTROL THE BRAKE TRANSMISSION SHIFT SOLENOID ALSO THE NEUTRAL SAFETY SWITCH.IF FUSE AND BRAKE LIGHT SWITCH IS GOOD.YOUR PROBLEM COULD BE A FAULTY NEUTRAL SAFETY SWITCH OR BRAKE TRANSMISSION SHIFT SOLENOID FAULTY.

May 05, 2010 | 2001 Chevrolet Cavalier

1 Answer

1992 buick regal won't start in the mornings after sitting overnight. when i try it in the early afternoon it starts right up


Next time it happen.

Put your foot on the brake,shift the gear selector to neutral "N" and start the car.

There is a switch call neutral safety switch and it can be intermittent.

If you can start the car in "N" and not in "P" then neutral safety switch is at fault.

Replace it as soon as possible to prevent damage to the wiring and transmission computer.

Nov 03, 2009 | 2000 Buick Regal

1 Answer

95 cherokee sport stalling


Since the car stall only in the drive position, it sounds(i'm not there to actually ck the car)like when the engine torques, it might be pulling on a harness somewhere and killing the ignition. Do this,start the car and under the hood while the engine is running, move or jiggle the harnesses around and see if the car stalls. If the car stalls try to pinpoint the location on the harness and look for frayed or broken wires.

Sep 03, 2009 | 1995 Jeep Cherokee 2 Door

Not finding what you are looking for?
1993 Ford Aerostar Extended Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...