Question about 2002 Chevrolet TrailBlazer

1 Answer

Brake lights dont work , bulbs are good and connections look ok,

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,124 Answers

The likely culprit is the break light switch..
Located on the break peddle shaft..
Not allot of money and pretty easily replaced..

Have a great day !

Please feel free to rate and comment for your free question on FixYa...

Posted on Sep 29, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 1999 cougar brake lights not working Fuse+bulbs+switch ok

I am asking you what switch you cheked and how did you know that is ok and working I had the same problem I replaced the switch under the brake pedal and it works fine if you still have this problem write to me @ absi20@hotmail.com thank you good luck.

Posted on Feb 06, 2009

  • 65 Answers

SOURCE: 2003 silverado 1500 v-6 brake lights dont work

HI!!!! brake ligth swich is located inthe brake pedal on top get them off is hold it by pins o screws replace this thing only if you check the fusess and the are ok.

Posted on Feb 26, 2009

  • 306 Answers

SOURCE: 2007 Chevy Silverado Center brake light works but back ones dont

There is a probable bad wiring connection in problem one and three.
#2 Possible water leak causing bulb break. Try wd40 in socket. you need a wiring diagam and cheap voltmeter if you want do it yourself.

Posted on May 09, 2009

honeymokey
  • 3113 Answers

SOURCE: brake lights suddenly do not

Brake light switch would be next.

Posted on May 10, 2009

  • 3600 Answers

SOURCE: I DONT HAVE PARKING LIGHTS, BUT THE TURN SIGNALS

check fuses if they are ok then you need to replace the light switch.

Posted on Jun 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2007 silverado 1500 brake lights dont work, bulbs are fine, power from the brake switch wire blue /white trace illuminates when the pedal is depressed


Check the bulb ground connection. Power may be reaching the bulbs but you need a ground to complete the circuit.

Apr 04, 2017 | Cars & Trucks

1 Answer

Rear brake lights dont work, bulbs are good, fuses are good


if the bulbs and fuse are ok it can only be the switch which u will find close to the brake pedal if u unplug the switch and then bridge out the plug this will bring on the brake lights which means the switch is at fault

Feb 23, 2011 | 2007 Chevrolet TrailBlazer SS

1 Answer

I have 99 chevy suburban my brake lights dont work i changed the switch, checked the fuse its good cleaned the connections and checked the bulbs they still dont work


See if there is a relay for the tail lights/brake lights. I would go ahead and install new bulbs. Make sure that you get the correct bulbs. Not many vehicles still use the old 1157's.

Dec 22, 2010 | 1996 Chevrolet K1500

1 Answer

My brake, hazard and turn lights dont work, i


well u have two seprate problems the hazards and turn signals have a flasher that needs replacing if the fuse is good on the fuse box marked signals .and there is a brake light switch under the dash board near the brake pedal it has two wires on it check the wires make sure they are connected if so replace the brake light switch

Nov 13, 2009 | 2002 Chevrolet Astro

2 Answers

Turn signals work but the brake lights do not how do i get them to work? i already changed the flasher.


I have a 2001 Ford F150, my brake lights dont work. Ive replaced the bulbs, checked the fuses,and the brake switch on side of the brake pedal was replaced. I still dont have any brake lights. My third brake light works fine, along with my running lights,flashers, blinkers.

Jun 18, 2009 | 1985 Ford F150

1 Answer

2005 chev trailblazer v6 4.2 rear side brake light dont work the top rear brake light works fuse 12 front works rear seat below fuse 16 and fuse 34 good bulbs good where do i check next


CHECK FOR POWER AND GROUND AT THE CIRCUIT BOARD FOR THE AFFECTED BRAKE LIGHT. IF THAT CHECK OUT GOOD THEN CHECK THE BULB CONNECTION FOR BURNED CONNECTORS, THIS IS A COMMON PROBLEM. LOOPING A TEST LIGHT FROM THE POWER TO THE GROUND CONNECTION AND HOLDING THE BRAKE PEDAL DOWN IT SHOULD LIGHT. IF IT DON'T THE CIRCUIT BOARD IS BAD.

May 16, 2009 | 2005 Chevrolet TrailBlazer

1 Answer

Brake lights quit working.


if all fuses and bulbs are ok get to the brake switch and see ifits stiff or stuck, if it just has two wires on it you could join themtogether to see if the brake lights come on though obviuosly dont leave them joined.Good luck davelee

Mar 23, 2009 | 1998 GMC Sierra

1 Answer

2007 Chevy Silverado Center brake light works but back ones dont


There is a probable bad wiring connection in problem one and three.
#2 Possible water leak causing bulb break. Try wd40 in socket. you need a wiring diagam and cheap voltmeter if you want do it yourself.

Dec 24, 2008 | 2007 Chevrolet Silverado Classic SS New...

1 Answer

1996 isuzu rodeo problem


TO TROUBLE SHOOT ELECTRICAL YOU MIGHT NEED TO TRY A GOOD BULB OF CORRECT TYPE INTO SOCKET IN BRAKE FIXTURE THEN ALSO MAKE CERTAIN THE REGULAR TAIL LIGHT ELEMENT IS GOOD REPLACE FUSE WITHOUT PRESSING BRAKE LIGHTS ON IF FUSE IS OK THEN TURN ON THE RUNNING LIGHTS SEE IF THE ONE IN QUESTION IS COMING ON IF IT IS AND THE FUSE IS OK THEN PRESS BRAKE PEDAL AND SEE IF THE BULB LIGHTS WITH THE BRAKE ON ALSO THE FOUR WAY FLAHER IF FUSE IF STILL GOOD IT MIGHT ALLOW DASH LIGHTS TO COME ON MANY VEHICLES HAVE A SAFETY WAY OF LETTING YOU KNOW YOU HAVE NO TAIL LIGHTS BY ALSO TURNING OFF THE DASH LIGHTS.

Nov 09, 2008 | 1995 Isuzu Rodeo

2 Answers

1991 volvo tail lights


Could you take out a bulb and with a testlight/probe check that you do in fact have power to that circuit .Also check that they are the correct bulb for that application I have seen people put indicator bulbs in where therse supposed to be a double filament bulb.Does the base of the bulbs lead contacts line up with the two steel terminals inside the plug?

Oct 20, 2008 | 1991 Volvo 240

Not finding what you are looking for?
2002 Chevrolet TrailBlazer Logo

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...