Question about 2008 Chevrolet Trailblazer

1 Answer

Trying to install a brake controller in a 2008 trailblazer. How do you intsall it? I found some wires under the dash on the driverside in a connector are those the wires you cut into?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,970 Answers

Here you can find information about trailer wires...
- Wiring harnesses & adaptors
- Trailer Wiring Diagram

I hope help you (remember rated this help) Good luck.

Posted on Sep 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2008 trailblazer. no brakes at all! not 3rd light either. fuses were good. now what?


Sounds like a bad brake light switch which is located under the dash on the brake pedal arm.

Jan 17, 2017 | 2008 Chevrolet Trailblazer

1 Answer

I am installing an electric trailer brake controller on my 2008 Ford F- 150 STX pick up truck and I need to know where it plugs in under the dash


Ford's factory supplied brake controller harness end can be found loosely stuffed under the dash, usually just above the driver's right leg. A Ford harness has a rectangular shaped connector.
Simply connect the brake controller harness connector into the vehicle connector. Zip tie the harness wires to another harness to prevent the wiring from hanging down near your feet.
I hope this helps.

Jul 03, 2011 | Ford F-150 Cars & Trucks

1 Answer

How do you install a brake controler for a towing package?


Alot of these trucks have the wiring hook up under the dash or at rear bumper area where you can just plug the wire harness from controler to it, but if not they are simple to wire and then you must level by following the instructions,you would wire it to power and ground then one wire to brake switch and the last wire goes to tow connector for electric brake on the trailer. for more help google how to install brake controller there you will find wiring diagrams and videos.

Oct 08, 2010 | 2008 Honda Ridgeline

1 Answer

2006 trailblazer with tow package electric brake hookup on dash


It's taped to a large bundle of wires just above the parking brake. There will be a large white sticker on it calling out each wire.

Aug 24, 2009 | 2005 Chevrolet Silverado

1 Answer

Where to wire the brake controller into on 2004 trailblazer


Hi
Not trying to discourage you but you can buy the new brake controllers if that is in fact what you did, that plug right into the wiring box on the left side of the brake pedal. Takes about 10 seconds to plug it in and is around 55 to 60 dollars at that parts stores. You don't have to do anything other then mount and plug it in.

Aug 21, 2009 | Chevrolet Avalanche Cars & Trucks

2 Answers

Electric trailer brake hookup


Truck Brake control

Red/Black stripe Black

Blue Blue

Lt. Blue/white stripe Red

White White

Orange Not used

Jun 28, 2009 | 2006 Toyota Tacoma

1 Answer

Trying to connect a teekonsha voyager brake control to a 2003 expedition


Their should be a 6 pin conector that only 4 pins are used somtimes a 5th wire is installed for illumination, don't worrie about using that one. The connector is located in one or two different spots, the most popular place is under the dash on the drivers side just below the steering column the connector is grey. The colors are black or red / blue / green / white and sometimes a small black or brown wire is for illumination, don't worrie about that wire. Their are wiring harnasses for sell to hook the brake control through the conector, but if you do not want to buy an adapter hook the wires as followed: Vehicle Brake Control
Black or Red Black
Blue Blue
Green Red
White White
Black is power in to the brake control
Blue is the trailer brake feed
Green is brake signal
White is Ground for the brake control

May 31, 2009 | 2003 Ford Expedition

1 Answer

No brake lights or turn signals on 2008 F450


try checking all of your fuses and see which ones are blown. you have two sets of fuses and they are under the hood of the vehicle and under the dash on the driverside or in the glove box. if the don't work after changing the fuses then your wiring for the turn signals and brake lights need to be cheked from the fuse boxes to the swith for the trurn signal and to your brake lights

Mar 24, 2009 | 1999 Ford Super Duty F 450

1 Answer

4pin blue modular plug under dash for brake controller to plug in


You should be able to access the Prodigy Instructions ie Wiring Diagram At google. Maybe an install video on You Tube. Make sure everything you do is properly fused. Any thing as far as color codes will need to be Prodigy specific. Prodigy may have a 1-800 Tech line. They should be able to E-mail you a PDF file.

Feb 28, 2017 | 1999 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...