Question about 2000 Daewoo Nubira

Open Question

Camshaft torque settings for daewoo nubira 1.6 xreg

Camshaft torque settings for daewoo nubira

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ray190te
  • 61 Answers

SOURCE: i need the torque spec for a 2000 daewoo nubira

Cam shaft cap bolts 16nm ,13lb-ft
Exhaust cam gear bolt 67.5nm ,49lb-ft
intake cam gear bolt same as exhaust

Posted on Jan 24, 2009

  • 1 Answer

SOURCE: replacing timing belt on daewoo nubira 2000 model

Instructions Difficulty: Moderate Things You’ll Need:

  • Set of ¼-inch drive sockets ¼-inch drive ratchet Set of ½-inch drive sockets ½-inch drive ratchet Set of 3/8-inch drive sockets 3/8-inch drive ratchet Set of metric wrenches Floor jack Jack stands
Step1 Raise and support the vehicle on jack stands. Remove the intake air temperature wiring, the breather hose and intake air hose. Take off the air cleaner assembly. Step2 Remove the right wheel. Remove the accessory belts. Remove the crankshaft bolt and the crankshaft pulley. Remove the power steering bolts and the timing belt covers. Temporarily install the crankshaft bolt and turn the engine clockwise until the mark on the crankshaft pulley, which is a triangle stamped into the crank sprocket, is aligned with the corresponding triangular mark on the block. Step3 Make sure that the timing marks are aligned on the camshaft sprockets. These are a line on each sprocket that runs through a tooth on each sprocket. These lines should line up in the middle between each sprocket and point toward each other. If they do not line up, turn the crankshaft one more time and they will line up. It takes two turns of the crank to one complete revolution of the cam. Step4 Loosen the water pump bolts; using the 3/8-inch ratchet, turn the water pump clockwise away from the belt and loosely tighten the bolts to keep it there. Remove the timing beltmag-glass_10x10.gif. Make sure the timing marks are aligned and install the new belt starting on the right side from the crank sprocket and working counterclockwise. Keep all the belt tension on the right side away from the tensioner. Step5 Loosen the bolts in the water pump and rotate the water pump counterclockwise to apply tension to the belt. Watch the tensioner, which is above the water pump, and apply tension with the water pump until the pointer on the tensioner lines up with the notch above it. Lightly tighten the water-pump bolts. Step6 Turn the engine two more times and align the timing marks perfectly. Loosen the water-pump bolts and, using the ratchet, apply tension to the belt until the tensioner pointers are aligned. Tighten the water-pump bolts. Step7 Install the timing-belt covers and the bolts in the power-steering pump and tighten. Remove the crankshaft bolt and install the crank pulley and the bolt, then torque the crankshaft pulley bolt to 70 foot pounds of torque. Install all components in reverse order of removal.

Posted on Mar 08, 2009

  • 1 Answer

SOURCE: how do i change the camshaft sensor on a 1999 daewoo nubira?

read all of this before you begin! you may be able to skip a step that i couldnt !no.you dont have to remove the timing belt but check it. i did this to my nubira like two months ago. the belt felt loose but i didnt change it and now my car is on the side of the road) remove breather box. remove spark plug cover(top of engine two allen screws).see cam pos sen. wire clip at front of engine facing down, dont try to remove yet. clips are at the top sides of timing belt cover. from under the car remove plastic covers where you may find them on the pulley side and passenger side wheel well. using socket wrench relieve tension on torsion wheel(smallest pulley your s-belt crosses) by pushing up. release s-belt and remove(you may want to draw a quick diagram of how your belt is ran before removing). now remove the bolts from the timing belt cover.(when i did this i was also changing my harmonic balancer or crank pulley,if it is in the way of bolts remove the four bolts with a allen wrench,loosen it with the s-belt still on and car in fifth gear if standard to keep crank from turning. next place a long board or plank under the engine (across trans-housing,oil pan, as little on the oil pan as possible . place a jack at the center of the board and gently raise the engine. this relieves pressure from the top engine mount. remove the engine mount entirely. remove all screws from timing belt cover. remove cover. you will see two camshft gears at the top of the engine just below them you will see one star head screw(can usually be removed with an alle n wrench). it hold the cam pos sensor in place, remove then pull sensor out the top of the motor. sometimes they're a little bit stuck down in there. just pry a little but dont pull on wires! once removed disconnect wire replace, and rebuild. hope this helps

Posted on Jul 19, 2009

stevenhurc
  • 450 Answers

SOURCE: looking for diagram of head bolt torque and timing

Tighten the cylinder head bolts to 25 NSm (18 lb-ft) and turn the bolts another 3 turns of 90 degrees using the angular torque gauge.

7322e00.jpg

Posted on Jul 21, 2009

alicantecoli
  • 22156 Answers

SOURCE: 2000 Daewoo Nubira camshaft position sensor

on the front under timing belt cover ,back cam ,if its not their then back of head about 3inches along from the gear wheel end

Posted on Sep 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What. Is. The. Position of. No 1piston. When. Setting. The. Timing. On. Daewoo. Nubira. Cdx. 2 l


after you remove the timing belt covers on the crankshaft gear have a noch face down to alaing tho the oil pump cover on the camshafts have two marks a the top of timing cover

Sep 09, 2014 | 2002 Daewoo Nubira

1 Answer

Hi, need head torque settings for a 2000 daewoo nubira 1.6, thanks


In four stages, first with a calibrated torque wrench, then an angular torque gauge.

1st stage 25 nm (18 ft/lb) 2nd stage 60 deg
3rd stage 60 deg
4th stage 60 deg
5th stage 10 deg
order:
10. 6. 2. 3. 7. 9. 5 .1 .4 .8

New bolts ahould be used when head, and/or gasket is replaced.

Thank you for useing FixYa and i hope this answers your question.

Jun 28, 2011 | 2000 Daewoo Nubira

1 Answer

What are the torque specifications and tightening sequence for cam journal and cylinder head for 2001 daewoo nubira 2.0 :(


  1. The torque settings for the cylinder head bolts on a daewoo ...

    www.answers.com > ... > Categories > Cars & Vehicles > Asian Car i need how much pression (torque) for head daewoo nubira 2001 2.0 ... What is the cylinder head torque specs for a 2001 daewoo nubira 2.0 litre engine and ...

Apr 15, 2011 | 2001 Daewoo Nubira

1 Answer

I HAVE A 2001 DAEWOO NUBIRA THAT RUNS FINE MOST THE TIME BUT OTHER TIMES IT LOSES POWER AND STALLS.SOMETIMES IT WILL CRANK RIGHT BACK AND STALL WHEN I PUT IN GEAR AND START TO GO.OTHER TIMES YOU HAVE TO...


If I recall correctly there was a recall on the camshaft position sensor. In some cases it would melt.
MAKE: DAEWOO MODEL: NUBIRA YEAR: 2001 DEFECT SUMMARY:
ON CERTAIN PASSENGER VEHICLES, THE CAMSHAFT POSITION SENSOR MAY MELT RESULTING IN A BURNING SMELL AND VISIBLE SMOKE, WHICH MAY SUBSEQUENTLY LEAD TO THE MELTING OF THE CAMSHAFT COVER AND THE CAMSHAFT POSITION SENSOR WIRE HARNESS.
CONSEQUENCE SUMMARY:
THIS COULD POSSIBLY CAUSE AN UNDERHOOD FIRE.
CORRECTIVE SUMMARY:
DEALERS WILL REPLACE THE CAMSHAFT POSITION SENSORS AND INSTALL AN ADDITIONAL FUSE. THE RECALL BEGAN ON SEPTEMBER 7, 2004. OWNERS SHOULD CONTACT DAEWOO AT 1-877-362-1234, OPTION 6, OR FIND A LOCAL DEALER THROUGH THEIR WEBSITE AT WWW.DAEWOOUS.COM.

Sep 15, 2010 | 2001 Daewoo Nubira

1 Answer

What are the specs on head bolts


2001 Daewoo Nubira 2.0L MFI DOHC 4cyl

The Head Bolt Torque ...

Torque sequence ------------------------- Front | 10 6 2 3 7 | of | 9 5 1 4 8 | Engine --------------------------

Step 1 - Torque to 18 ft/lbs Steps 2 - Turn 90 degrees Steps 3 - turn 90 degrees Steps 4 - turn 90 degrees Recheck final torque in sequence


Hope helps (remember rated and comment this).

May 27, 2010 | 2001 Daewoo Nubira

3 Answers

Need cam torque specs


1999 to 2002 - 2.0L DOHC

Camshaft bearing cap bolts intake and exhaust.

N.m (INCH LBS)
8 ( 71 )

Jan 23, 2010 | 2001 Daewoo Nubira

2 Answers

Cam cap bolt torques for a 2001 daewoo nabira


Tighten
Tighten the intake/exhaust camshaft caps bolts to 16
Nm (12 lb–ft).

c272e38.jpg

Jan 17, 2010 | 2001 Daewoo Nubira

2 Answers

2000 Daewoo Nubira camshaft position sensor


on the front under timing belt cover ,back cam ,if its not their then back of head about 3inches along from the gear wheel end

Sep 11, 2009 | 2002 Daewoo Nubira

2 Answers

Torque specifications cylinders head bolts


for 1.5/1.6L DOHC, 18 Ft-lbs + 70deg + 70deg + 50deg

for 1.8/2.0L DOHC, 18Ft-lbs +90deg + 90deg +90deg

Jun 09, 2009 | 2001 Daewoo Nubira

1 Answer

I need the torque spec for a 2000 daewoo nubira


Cam shaft cap bolts 16nm ,13lb-ft
Exhaust cam gear bolt 67.5nm ,49lb-ft
intake cam gear bolt same as exhaust

Nov 25, 2008 | 2002 Daewoo Nubira

Not finding what you are looking for?
2000 Daewoo Nubira Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...