Question about 2005 Renault 18I

Open Question

My engine is cranking for few secondes and stop without starting. plese note that the engine was working properly before and i stoped the car without any problems. is it somthing related to the immobiliser or the alam job. thanks for your support i realy apreciate it.

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1986 Answers

SOURCE: Flat battery caused immobiliser problems

1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works

Posted on Aug 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes my car to stop running while being driven?


Could be almost anything.
If it cranks good but, won't start, make sure battery has a full charge. Don't crank the starter more than a few seconds at a time, let it cool off. Have helper crank it, while you visually check for spark at the spark plugs. If spark everywhere, use a gage and check proper fuel pressure. Also, check fuel injector pulse, do testing with engine cranking.
How long since a tune-up? Any applicable trouble codes?

Mar 22, 2016 | 1996 Pontiac Grand Prix

3 Answers

Excessive crank time on cold engine start


The way the newer systems work the engine spins at least a few turns while the computer checks everything for correct readings. In the old days it was "cool" to be able to reach in and "bump" the key and have the car start. It meant you had the car tuned perfectly. Now the vehicle computer will not turn fuel on until it is happy with readings. One trick you can try is turn key to full on position and let it sit for a second or two before turning key the rest of the way to crank. This allows the system a second to do it's checking without wasting power cranking. Had Nissan that was just like this. Just wait a few beats before turn to full crank. You can also listen for fuel pump whine in that few seconds, and then hopefully whine to stop when pressure hits full. If whine never stops fuel pump may be getting weak. If you can get access to higher end code reader you can also check for "pending" codes that may be showing up sometimes (holding start up) but then working (so engine finally fires).

Feb 27, 2015 | 2000 Isuzu Rodeo

1 Answer

Stalling and stoping and not starting up cranks fine


low fuel pressure.. clogged fuel filter..malfuntioning emissions controls...bad auto shutoff relay.. check all..

Feb 02, 2014 | 1999 Lexus LS 400

1 Answer

1990 s-10 4 cylinder 2.5, 5 speed, throttle body injection, 120,000 miles won't start without stating fluid. Runs fine after started, I've changed fuel pump, filter, plugs. I appreciate any help.


My first question would be is the injector spraying when you crank it ?
The way its supposed to work, the fuel line to the tank should have about 10psi of pressure before you crank the engine. When you turn the key on the pump gets power for 3 seconds to boost the pressure. The pump stops working until the engine has oil pressure which takes a few seconds.
If the base fuel pressure leaks back to the tank, or the pump relay is not powering the pump, you won't have any fuel pressure or spray until you get oil pressure.

Dec 12, 2012 | Cars & Trucks

1 Answer

Rpm not working and run for a few seconds and cuts off


possible crank sensor problem. the 3800 engines were noted for this failure. although could be a bad module, cam sensor or associated wiring

Aug 31, 2012 | 1997 Buick Riviera

1 Answer

I ran out of diesel. put some in and car still wont start


1. The engine does not have any fuel system screw bleeder!
2. The only one way for start the engine is to fill up the tank, then turn the ignition key in "ON" position for 4 - 5 times, wait for 10 seconds between two attempts, without cranking engine.
3. After that push the clutch pedal, (if exists), to the floor, and the accelerator pedal to the floor too. Now turn the ignition key in "ON" position, wait for 5 seconds, and crank the engine for maximum 40 ... 50 seconds. Wait for 60 seconds between two starting attempts, in order to save the battery & starter motor.
4. Repeat the step no.#3 until start the engine.

IMPORTANT NOTE: DO NOT TOW THE CAR IN ORDER TO ATTEMPT TO START THE ENGINE!!!

Nov 24, 2010 | 2006 Audi A4

1 Answer

Francois Silver ? Walvis Bay - Namibia I have a 97 Chevy K2500 Cheyenne V8 fuel injection. I have a starting problem. When turning the ignition key, the fuel pump comes on and stops after 2 to 3 seconds....


It has nothing to do with ECU and immobiliser even if you turn your ECU OFF your car will start and will your but not properly without CPU your car will work in emergency mode. try finding Idle sensors and check them if they are ok

Jan 29, 2010 | 1997 Chevrolet C/K 2500

2 Answers

Mazda rx8 flooded .brakedown come tried to start engine turned over !then starter got hot ,now dosnt turn over just clicks? any wdvice please


Your problem is common in the RX-8. It occurs when you start a cold engine and shut it off before it reaches normal operating temperature. If your car does flood, you can first try depressing the accelerator completely and holding it (which shuts off the fuel pump) and then crank the motor for about 10 seconds (not longer or you may damage your starter). If this procedure above does not work, here is the technique a Mazda dealership will normally use (to be performed at your own risk): 1. Use jumper cables to connect to another car battery. 2. Unplug Air pump connector (the black circular motor housing to the left of the oil filler cap) 3. Take fuel pump fuse out (number 22, a 20 amp, 3 from the top of the second column of the fuse box 4. Crank for 4 seconds, pause for 2 seconds, repeat for about a minute 5. Leave for a minute 6. Crank for 4 seconds, pause for 2 seconds, repeat for about a minute 7. Put fuel pump fuse back in 8. Crank for up to 10 seconds, if it catches but doesn?t start, stop cranking 9. If not started go back to step 3 10. If started, wait 30 seconds for oil pressure to rise 11. Stand on throttle until white smoke stops coming out of the exhaust 12. Disconnect jump leads 13. Leave to warm up on idle for a few minutes 14. Put air pump connector back on (see note 3) 15. Go for a nice long drive to recharge the battery

Dec 27, 2009 | 2004 Mazda RX-8

1 Answer

2007 Jeep Wrangler Unlimited Sahara


SUBJECT:
Long Crank Time Due To Possible Contact Of Camshaft Sensor To Camshaft Gear
OVERVIEW:
This bulletin involves the replacement of the engine camshaft sensor.
MODELS:
2007 (JK) Wrangler
NOTE: This bulletin applies to vehicles equipped with a 3.8L engine (sales code
EGT).
SYMPTOM/CONDITION:
The customer may experience one of the following conditions:
a). Long engine crank time.
b). Two engine start attempts prior to engine starting.
c). Due to the “TIP Start Feature” on automatic transmission equipped vehicles, once the
ignition key / switch has been released from the “START” position, the starter may stay
engaged for up to 10 seconds while the engine attempts to start.
The above conditions may be due to the position of the camshaft sensor to the camshaft
gear. The sensor spacer gasket may have come loose during engine assembly and
caused the camshaft sensor to be adjusted too close or in contact with the camshaft gear.
DIAGNOSIS:
If the above condition is present perform the Repair Procedure.
PARTS REQUIRED:
Qty. Part No. Description
1 04686353 Sensor, Camshaft

Jul 12, 2009 | 2007 Jeep Wrangler Unlimited Rubicon 2...

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

xxxxxx xxx

Level 3 Expert

4834 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...