Question about 2000 Dodge Durango
How do I replace the variable speed sensor on a 2000 Durango.. v-8, auto, 4 wheel drive?
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2001 dodge durango v8 4.7
It is acually called the vehicle speed sensor I do believe. It should should be located on the top of your transmission with a wiring harness attached to it. It should also have 1 bolt holding it in also. Whatever you do, do not rotate the gear when you remove it. Try to mark the exact way it came out when you replace the sensor. When you pull the sensor out it will have this gear attached to it which will need to be placed into the new sensor and put back into the vehicle in the same way it came out or you will throw a code and it will not be pretty. Good luck, hopefully I didn't scare you it can be a simple repair just mind your P's and Q's.
Posted on Jan 07, 2009
I Fixed it !!! What happened was that the "O" ring that came with the filter wasn't fully seated in the pump before i put the filter on. It was kind of hard to get it to seat properly I had to get a hammer and a socket w/ an extention and tap it in. It wont go in with finger pressure alone. To find out if this is what the proble is then take off the pan and remove the filter, if the "O" ring is attached to the filter when u remove it then this is the problem.
Posted on Apr 06, 2009
SOURCE: engine code p0700 need help
I have been diving into my factory service manual, and the P0700 should have another trans trouble code stored with it, a "Generic" code reader may not be able to read the other trans code, if it after a trip to the dealer to sort out this code turns up nothing (no other stored codes) then there may be a problem in the TCM (Transmission control module) so u should get this to the dealer and have them read the codes and report them to u.
Posted on May 15, 2009
Its in different locations depending on if its 2wd or 4wd. For 2wd its in front of the drice shaft or for 4wd its in the tranfer case, just look for a white shape like box with wires plugged into it and you need a socket to remove it, iam not sure how much it is to replace as the cost varies at different shops.
Posted on Jun 19, 2009
1st try and search for a vaccum leak, due to the fact that these vehicles have had some bad problems with the length of wires and hoses, if there is a vaccum leak in the vehicle somewhere that will trigger other malfunctions in your vehicle. Using a can of starting fluid or Brake cleaner spray lightly spray around our engine til you hear the motor rev-up and the spot you have sprayed will determine where your vaccum leak will be. And then check under your distributor cap for any moisture be sure to take a rag and wipe and residue off. Also check the firing order on your distributor.
Posted on Oct 28, 2009
Tips for a great answer:
Nov 18, 2014 | 2000 Dodge Durango
Jan 05, 2014 | 2000 Dodge Durango
Sep 24, 2010 | 1999 Dodge Durango
Jul 08, 2017 | 2000 Dodge Durango
Apr 01, 2010 | 2000 Dodge Durango
Feb 03, 2010 | 2000 Dodge Durango
Jan 31, 2010 | 2000 Dodge Durango
May 17, 2009 | 2000 Dodge Durango
Dec 16, 2017 | 2000 Dodge Durango
Jul 23, 2008 | 1999 Dodge Durango
124 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: