Question about 1990 Chevrolet K1500

1 Answer

HOW DO I REMOVE THE IGNITION SWITCH. 1990 chevy truck, 1500series

Posted by on

  • 1 more comment 
  • bjhatton Sep 29, 2009

    The whole cylinder.

  • bjhatton Oct 05, 2009

    I had to make two tools to reenisall the switch and steering wheel.

  • yadayada
    yadayada May 11, 2010

    lock cylinder or actual switch?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 347 Answers

Its a tough job u have to pull steering wheel first then the steering wheel lock they are a screw in sind goes in and hold switch some has a push pin

Posted on Oct 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the ignition cylinder on a 90 lumina


I just did that last week. Remove horn, remove steering wheel, remove blinker switches, remove tilt spring, remove tilt mechanism, remove key buzzer switch (mine was white with 2 small wires leading to it). Screw holding ignition cylinder in should now be visible. P S Let me know if you have any trouble removing all the items listed above and I will try to help.

Jul 12, 2012 | 1990 Chevrolet Lumina

1 Answer

How do you install an ignition switch in a 1990 Chevrolet 1500?


Remove lower instrument panel trim panel. Remove two steering column to dash and brake support bracket nuts and lower the steering column. Remove the two ignition switch to column screws and lift the switch off of the lock rod. Remove the black harness connector first and then remove the white harness connector.

Mar 27, 2011 | 1990 Chevrolet K1500

1 Answer

My 1990 chevy lumina the key wont turn to turn my car off


sounds like the ignition cylinder is worn and binding in the housing-could also be a damaged ignition switch as well

Aug 16, 2010 | 1990 Chevrolet Lumina APV

2 Answers

Need to remove ignition switch on a 1990 jeep cheeroke


Remove lower instrument panel trim. remove 2 steering column to dash/brake support nuts and lower steering column. remove screws holding ignition switch to column and lift switch off of lock rod. first remove black harness connector, then remove white connector from switch.

Apr 10, 2010 | 1990 Jeep Cherokee Limited

1 Answer

No power to wiper motor, 1990 chevy s-10 blazer. No power to fuse block (just the wiper fuse)


It would have to be in the ignition switch,this ,when turned on,sends power to the fuse.

Feb 25, 2010 | 1989 Chevrolet S-10 Blazer

1 Answer

1990 chevy suburban. The key was turned to auxillary and stuck


hopefully that does not have tilt steering which makes the job somewhat more difficult. the same thing happened with a van i owned. there are small arms inside the steering column that move with the key to move the ignition switch.
to confirm it is broken locate the ignition switch on the column. remove it then turn the key. if the piece that normally moves that switch doesn't... than it is broken.

first unhook the battery.

about the only way to get at it is to remove the steering wheel. there are more parts behind that that have to be removed. then you will get to what is basically and end cap. remove that and slide out the parts and install the new arm(s) mine was a 2 piece.

basically you just need to bolt it back up and reinstall the key cylinder and you are good to go. hook up the battery again and you should have a working vehicle.
the tilt springs can be held together with a c clamp. it is tricky but you will see as you attempt it.

Nov 28, 2009 | 1990 Chevrolet Suburban

1 Answer

1990 chevy tilt streeing column .Haveing trouble


There is some adjustment. But you may have something else going on. When the tilt gets old the pivot pins get loose and the holes get egg shaped. If this is what is going on then you might me wasting your time.

Nov 11, 2009 | 1990 Chevrolet K1500

1 Answer

Removal of 1976 chevy truck ignition switch


need a special tool to remove the locking plate behind steering wheel then pull turn signal switch back a little then remove screw that keeps lock cylinder in place

Oct 22, 2009 | Chevrolet C3500 Cars & Trucks

1 Answer

How do I replace the ignition switch in a 1990 K1500 chevy pick up


Underneath the dash, follow the steering column and you'll find a square longer-type switch with an electrical connector on one side and a rod coming out of the end of it going towards the dash. It's held on by 2 quarter inch (or smaller) bolts. Remove the connector, remove the two screws, and slide the switch out of the rod. Install reverse of removal.

Aug 22, 2009 | 1990 Chevrolet K1500

1 Answer

Installing ignition switch in 1990 chevy pickup


how to replace ignition switch in 1990 chev 1500 pickup long bed

Aug 21, 2008 | 1990 Chevrolet K1500

Not finding what you are looking for?
1990 Chevrolet K1500 Logo

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...