Question about 2000 Daewoo Lanos

1 Answer

New slave and master for clutch still will not engage did bleed

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Daewoo Master
  • 1,564 Answers

If all the air is out of the clutch system than you probably have badly worn fingers on you clutch plate and it should be replaced as an assembly, clutch disk, clutch plate(pressure plate) and throwout bearing. Thank you, Dana

Posted on Sep 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 ford focus 2.0liter. clutch pedaL GOES TO FLOOR. brake master full of fluid.I clutch master or clutch slave cylinder bad?


a plastic master cyl !

master cyl is bypassing internally

slave cylinder is inside the gearbox bell housing
if its leaking .....gearbox out




26351104-h2ljceqgvzc5xcxajl4olrsz-4-0.jpg

26351104-h2ljceqgvzc5xcxajl4olrsz-4-1.jpeg

26351104-h2ljceqgvzc5xcxajl4olrsz-4-3.jpg

Nov 11, 2016 | 2004 Ford Focus

3 Answers

Clutch letting off at the top


bleed the slave. Your throw isn't as far as it should be.

Dec 18, 2013 | 2003 Hyundai Tiburon

1 Answer

I have a 2000 mazda 323 with a manual transmission. i have already change the clutch kit but the gear is still hard to shift


Check the hydraulic clutch operation. This is a clutch master cylinder with a reservoir on the firewall, and a clutch slave cylinder down on the bell housing of the transmission, with a steel tube running from the master to the slave cylinder. When clutch pedal is depressed, hydraulic fluid (brake fluid) is forced from the master to the slave. The slave cylinder should push out a little plunger that contacts the clutch fork lever-pushing it forward to engage the clutch.
Add brake fluid to the reservoir if needed. Watch the plunger on the slave cylinder: if it moves little, or not enough, try bleeding the slave from the bleeder valve. They are bled just like brakes. If bleeding doesn't help, your clutch master or the slave may need replacing. The master cylinder, like a brake master, has internal seals that hold hydraulic pressure, so force can be applied to the plunger on the slave cylinder.

Dec 09, 2013 | Mazda 323 Cars & Trucks

2 Answers

2006 chevrolet cobalt clutch issues


Just because the master is new does not mean it isn't faulty. If you are certain you have bleed all the air from the system, I suspect you got a bad master.

Nov 21, 2012 | 2006 Chevrolet Cobalt

1 Answer

94 Chevy 2500 Clutch Engagement?


You probably have a hydraulic clutch. A hydraulic clutch has both a master and a slave cylinder. The slave cylinder engages/disengages the clutch plate. You might be low on clutch fluid in the master cylinder, or the system may need to bled similar to bleeding brakes. Worst case is you need a new clutch, pressure plate, and throwout bearing. They should all be replaced when doing a clutch job.

Aug 23, 2012 | Cars & Trucks

3 Answers

Why does clutch leak off and wont go into gear 96 toyota tacoma when you push on clutch pedal goes to the floor it wont engage clutch to be able to put into gear


the most likely reason is either the clutch master cyl. needs to be replaced.or the.slave cyl. its mounted down on the transmation under the hood find the resivore for the clutch. check the fluid level.if its low , fill it back up , and look for signs of a leak
you will probally have to bleed out all of the air from the system.its done almost the same way as bleeding the brakes. Good Luck.

Nov 05, 2011 | Cars & Trucks

1 Answer

I need help changing out the master cylinder in my '94 toyota 4x4 pickup truck. It is a 5speed, i have already changed out the slave cylinder and installed the master cylinder but i still can not get the...


did you bleed the system?? you must bleed the system from the clutch slave. if this has been done, I need more info!! How does the clutch pedal feel, is the clutch slave engaging at all??

Sep 27, 2010 | 1994 Toyota Pickup

1 Answer

Clutch fails to dis-engage clutch. 1986 F250 3/4ton 7.5 2wd


Make sure the slave cylinder body is attached firmly, then bleed the air out of the hydraulics--similar to bleeding brake lines. Watch the clutch mechanics while someone operates the clutch, (engine off) you should see definite movement. If you get movement and no clutch action, you may have to reappraise your clutch installation. Hope this helps!

Dec 19, 2009 | 1986 Ford F 250

2 Answers

I have changed the clutch master cylinder and the slave cylinder, but still don't have pedal, we have bleed the lines and checked for leaks, no leaks were found. The new slave cylinder doesn't seem to be...


Thn the problem is the clutch master cylinder, it should build up pressure, ok try out this, remove the pipe which is going to the slave cylinder either from the clutch master cylinder or at the clutch slave cylinder and get someone to pump the pedal while you block the pipe and see if there is fluid thrown out with pressure.If there is pressure there thn fit back the pipe and refill the reserviour wth brake fluid and open the bleeding nipple at the slave cylinder let some fluid pour out and tighten it and thn pump the pedal and retry bleeding.
If there is no pressure at the pipe thn its the clutch master cylinder.
Hope this helps!

Dec 14, 2009 | 1997 Acura CL

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

Not finding what you are looking for?
2000 Daewoo Lanos Logo

Related Topics:

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...