Question about 2002 Volkswagen Golf

1 Answer

Hello. Could you please advise me what the camshaft torque tightening specs are for a 1993 SEAT IBIZA . Thank you

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Volkswagen Master
  • 14,036 Answers

CAM SHAFT BEARING CAPS 15 FT LBS. DRIVE SPROCKET BOLT 58 FT LBS. CAMSHAFT END PLAY IS 0.006 in. WARNING THIS IS THE 2.8L ENGINE WHEN TORQUEING CAM SHAFT BEARING CAPS YOU HAVE TO TIGHTEN THE BOLTS 2 TURNS AT A TIME IN A DIAGONAL PATTERN TO DRAW THE CAMSHAFT DOWN AGAINST THE VALVE SPRING.

Posted on Sep 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

I need the torque settings for toyota corola 1993 cylinder head torque please ?


Hi Manuel, There are a number of different engines used in the Corolla, knowing which would be a great help. The engines used in the 1993 are of the 'A' series and 'E' series. The torque for the A series is 29 nm + 90 degrees. When removing the head begin loosening from the outer bolts. When the head is off have it inspected for warpage and skimmed if it is required. Tightening any cylinder head always begins at the middle or centre and works outwards. As my friend has said, the camshaft caps are tightened to 9 nm and the inlet manifold goes to 24 nm, and the exhaust is 27 nm. The tappet cover I think is 29 nm. The tappet cover is tightened on the A series with nuts onto the plug tubes. Regards John

Mar 29, 2014 | 1993 Toyota Corolla

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

Intake Manifold tightening sequence plus torque specs


start in the middle and alternate left to right and the torque on a alloy manifold will be around 14lbs or a nip with a 3/8th drive rachet ,any water passages use contact adhesive around the water ports .

May 25, 2012 | Chevrolet Corsica Cars & Trucks

1 Answer

What are the torque specs. for the harmonic balancer on a 2004 ford explorer with the 4.0 V6


Hello qsswanson33: My name is Roger and I will help with your answer. Tighten the bolt to 33 ft.lbs. then tighten an additional 85 degreese. This will acheive the propper torque. Should you need further help please just ask. Please rate the answer. Thank you for using Fix Ya. Roger

Aug 01, 2011 | Ford Explorer Cars & Trucks

1 Answer

Seat inca van 00 sdi 1.9 diesel.. tension polly came loose.. timing belt slipped.. I need to know how to reset it again. Where are the markings on the crank shaft and the cam shaft? Please attach any...


Timing belt set-up for a 2000 Seat Inca 1.9 SDi

1. Align the crankshaft timing marks on the flywheel / gearbox

tdisline_583.jpg
2. Remove the valve cover
3. Lock the camshaft

tdisline_584.jpg
4. Fit the injection pump locking pin

tdisline_585.jpg

5. Loosen the camshaft gearwheel bolt, 180 degrees. Use a wrench to counter-hold
6. Loosen the camshaft gearwheel while holding it in place

tdisline_586.jpg

7. Fit the timing belt in the sequence as shown in the below figure: a - b - c - d - e - f - g

tdisline_587.jpg

8. Fit the timing belt and camshaft gearwheel together
9. Turn the tensioner clockwise to align both marks

tdisline_588.jpg

10. Tighten the large bolt on the tensioner to a torque of 20 Nm
11. Check for correct fit
12. Lock the camshaft. Tighten the camshaft gearwheel bolts: 45 Nm. Use a wrench to counter-hold
13. Remove helping tools
14. Turn the engine two rotations by hand
15. Repeat the procedure if required
16. Fit the vacuum pump
17. Refit the crankshaft pulley. Tighten torque: 20 Nm + 20 degrees
18. Fit the timing belt cover
19. Refit the valve cover
20. Fit the ancillary drive belt
21. Refit the inlet air manifold hoses
22. Check the injection timing

Torque settings:
Camshaft gearwheel: 45 Nm
Tensioner pulley: 20 Nm
Crankshaft pulley: 20 Nm + 20 degrees

May 26, 2011 | Volkswagen Passat Cars & Trucks

1 Answer

The torque specs for a 1999 4.6 liter northstar camshaft cap bolts


Hello: The following is straight from the 1999 4.6 service manual----Install the bearing caps according to the identification marks. The arrow should point toward the front of the engine. the number indicates the position from the front of the engine and the I or E indicates intake or exhaust camshaft. hand start all bolts. Tighten to 44 lb. in. plus 30 degrees Start from front and work back. A torque angle meter is used to measure degrees.

Sep 18, 2010 | Cadillac Cars & Trucks

1 Answer

What are the head bolt specs for a 95 tercel


Hello proskater442: My name is Roger and I will help you. The cylinder head torques in two steps. Make sure all bolts are good before attempting to torque them Inspect for any broken or deformed threads. Replace any that are damaged. I attached a picture of the torque specs. and tightening sequence. Should you need further help please just ask. Thank You for using Fix YA. Roger11e7f20.jpg

Jun 07, 2010 | 1998 Toyota Tercel

1 Answer

I need torque specs for head bolts on 1992 merc benz 230 e


hello,230e with engine 102.982,cylinder head bolt,double hexagonal socket m12, stage 1, 55 newton meter,stage 2 90 degrees stage 3 90 degrees,4 pcs. bolt with m8 tighten to 25 nm.ref. technical data year 1993,ty

Apr 17, 2009 | 1992 Mercedes-Benz E-Class

1 Answer

Kia sedona 2002


You should begin tightening from the middle and work your way out on each camshaft: Tighten the bearing cap in two or three steps. Tighten it to the standard torque at the last stage. *Bearing cap standard torque Torque
16 pieces at the both ends : 18.6 - 20.6 N·m
(190 - 210kg·cm, 13.7 - 15.2 lb·ft)
24 pieces in the middle : 10 - 12 N·m
(100 -120kg·cm, 7.38 - 8.85 lb·ft)

Jan 18, 2009 | 2002 Kia Sedona

Not finding what you are looking for?
2002 Volkswagen Golf Logo

315 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...