Question about 1999 Chevrolet S-10 Pickup

1 Answer

How do you replace the starter on a 1999 Chevy S10 4 cylinder?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 496 Answers

Hi,
Start by disconnecting the negative battery cable.
I don't know if your vehicle is 2 wheel or 4 wheel drive, but please note that on some 4WD vehicles, access to the starter is difficult due to the front driveshaft and/or related hardware. This may or may not be the case with your vehicle, but be prepared to remove other parts if necessary.
There are two bolts that are installed vertically at the bottom of the starter near the bell housing cover. Remove them and hold the starter up while doing so. The starter should then drop down far enough to disconnect the wiring attached to the solenoid. Note where the wires are removed from in order to reconnect them correctly.
Remove the starter and reverse the process to install the new one.
You may have to twist and/or reorient the starter to get it out and to replace it. Remove other parts, such as the bell housing inspection cover, as necessary.
Good luck with your project! Hope this helps...

Posted on Sep 29, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 217 Answers

SOURCE: how do i adjust the

you need to make sure your rear brakes are adjusted up properly and then adjust your emergency brake.the adjustment cable is along the frame on the drivers side.

Posted on Feb 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REMOVE CHEVY TRACKER STARTER


How do we get the starter out of my 1999 chevy tracker so we can replace it?

Jul 16, 2012 | 2003 Chevrolet Tracker

1 Answer

My Distributor shaft gears stripped out I will need to replace the gears. I have no idea how to figure out when #1 cylinder is at top dead center for the enitial timing.I am working on a 1999 chevy vortec...


remove plug from #1 cylinder have someone to bump the starter , while you place a finger over the spark plug hole, when the pressure from the cylinder blowes your finger off of the hole, check the timing marks,if they are lined up right ,#1 should then be on "top dead center"
hope you make it !

Sep 25, 2011 | Chevrolet Chevy Cars & Trucks

2 Answers

L999 Chevy Cavalier keeps blowing fuses and won't start


you have a SERIOUS electrical problem. - '.
BUT which fuses keep blowing - that is where we need to start.
1. is it the ignition circuit. - - does starter motor turn over when you trun the key.
2. is it the starter relay circuit.
3. is it the starter motor circuit.
4. is it the computer circuit. - - do you have fuel pumping to the engine and cylinders.
5. none of the above. - - do you have spark at the spark plugs.

Apr 14, 2011 | 1999 Chevrolet Cavalier

1 Answer

Last week my 1999 chevy shut off while it was running outside of my house... Tried replacing the coil & changing the battery & it still won't crank. The electric works fine but engine only makes...


Sounds like your starter is bad, the clicking is the starter solenoid, but the starter motor don't work, starter motor and solenoid, will come as one assembly, replace starter.

Sep 16, 2010 | 1999 Chevrolet Tahoe

1 Answer

HOW DO I FIX/REPLACE STARTER ON 1999 MALIBU?


Starter Solenoid needs to be replaced.
Remove starter and install new solenoid

May 05, 2010 | 1999 Chevrolet Malibu

2 Answers

Where is the starter located on a 1999 chevy


Follow the positive battery cable down to the starter.

Dec 27, 2009 | 1999 Chevrolet Malibu

1 Answer

1999 chevy blazer. brake pedel go to floor. getting flow. with no pressure. maybe brake booster? master cylinder?


If you are not having to add any brake fluid to the master cylinder the master cylinder must be replaced.

Oct 23, 2009 | 1999 Chevrolet Blazer

1 Answer

How to change my starter on a 1999 Chevy P10 Step Van


Remove the negative cable from the battery.
Remove wires off of starter.
Remove 2 starter bolts.
Reuse shims that may be installed.
Replace the starter in reverse order.

Jun 09, 2009 | 1999 GMC Sonoma

2 Answers

Starter replacement......needs to know how many cylinders my cars has


The starter has no cylinders. it is an electric motor powered from the battery and ignition system.
The chevy cavalier has a 4 cylinder engine though.

Jun 02, 2009 | 1992 Chevrolet Cavalier

1 Answer

1999 suburban starter replaced battery good turns over eratic


The starter may be binding on the flywheel/flex plate. Your new starter should have come with shims. Try putting them between the starter and the block one at a time and see if that helps.

Dec 20, 2008 | 1999 GMC Suburban

Not finding what you are looking for?
1999 Chevrolet S-10 Pickup Logo

2,362 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...