Question about 1994 Ford Probe

3 Answers

How do I replace a water pump on a ford probe coupe 1994 automatic 6 cylinder

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

This is amazing how is it possible for this guy name steve to give ppl advice on how to replace water pump on a probe here. read what he said carefully "drain coolant system..remove belt...remove all bolts..careful to not strip them, rotate removal off screws have a new gasket ready to but on new one and do the reverse..after installing i'd put into a can of pump lubricant and then a 50/50 mix of antifreeze..you can but it premixed." even a crackhead can tell you that much, the best advise here is the one boydlawnmowr has said here" i have a 95 ford probe gt, and i replaced my water pump myself. my advice to you is, if you are not a mechanic that has a carlift, metric tools, small hands, and no time frame, i would pay someone to do it for you. i will not do mine again, but if i had to i would pull the motor out and do it. if i hadnt of got my hands on a master mech. serving books, im not sure if i would have ever got the job done." its very time consuming and if you dont have the proper tools to do this you are looking to just get trapped because here is what ppl dont tell you the crankdshaft pulley has to come off the timing chain has to come last but not least the motor mount has to be removed and low jack needs to be used to lift engine up and down as needed to have aproper leverage for water pump removal. so you can imagine its no joke its crazy how this is incorporated deep under the hood

Posted on Apr 06, 2012

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

I have a 95 ford probe gt, and i replaced my water pump myself. my advice to you is, if you are not a mechanic that has a carlift, metric tools, small hands, and no time frame, i would pay someone to do it for you. i will not do mine again, but if i had to i would pull the motor out and do it. if i hadnt of got my hands on a master mech. serving books, im not sure if i would have ever got the job done.

Posted on Oct 09, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 921 Answers

Drain coolant system..remove belt...remove all bolts..careful to not strip them, rotate removal off screws have a new gasket ready to but on new one and do the reverse..after installing i'd put into a can of pump lubricant and then a 50/50 mix of antifreeze..you can but it premixed.

Posted on Sep 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is egr valve on 1994 ford probe, 4 cylinder


getta repair manual at partsplace or go to library sec629 for details

Mar 26, 2012 | 1994 Ford Probe

1 Answer

How to change water pump on 1991 ford probe?


The water pump appears to be near the top of the engine on the passenger side of the car,you need to replace the water pump from under the car.The car has to be lifted on jackstands.
--------- For details and appropriate diagram,click this link below and get more details:---
http://technoanswers.blogspot.com/2011/10/how-to-replace-water-pump-on-1991-ford.html ------------ This should help.Thanks.Helpmech.

Oct 07, 2011 | 1991 Ford Probe

1 Answer

Im just asking what size the motor for a 1994 ford probe???


A dual-overhead-cam 4-cylinder engine powered base Probes in 1993, developing 115 horsepower. The GT coupe held a 164-horsepower V6, also of dual-overhead-cam configuration. Both engines are Mazda designs. No more turbocharged engines were available. A 5-speed manual transmission was standard; 4-speed overdrive automatic optional. Except for a slight horsepower/torque boost in 1995 for the 4-cylinder engine, and a mild V6 torque increase the year before, powertrains saw no change in this period.

zjlimited_447.jpg

Hope this helps (remember to rate this answer).

Jan 12, 2011 | 1994 Ford Probe

2 Answers

I Have a 92 ford probe lx 3.0 v-6 5-speed and everytime i press on the clutch the pedal doesnt come back up any ideas why


hi, you may run out of fluid, find the clutch pump container and fill it up with brake fluid, if you see that is getting better then you have to bleede it out, hope it helps.

Dec 21, 2010 | 1992 Ford Probe

1 Answer

I have a 94 ford probe 4 cylinder 2.0 liter engine could a 96 ford f150 battery fit?


take the battery out of the probe and try it, if it fits in the tray and does not hit the bottom of the hood then when you close then it fits.

Dec 15, 2010 | 1994 Ford Probe

1 Answer

How do you change the belts (power steering, air conditioning, and water pump) on 1994 dodge shadow?


2.2, 2.5 (4 cylinder) or 3.0 (6 cylinder)?

On the 4 cylinder models the belts are just held on by various tensors either attached to their accessories (alternator, Powersteering) or via a pulley (AC, water) Release the tension, remove and replace the belt.





Jan 30, 2010 | 1994 Dodge Shadow

1 Answer

Diagram for intake manifold and fuel lines93 ford probe 4 cylinder


I have a 1994 Ford Probe with a Mazda MX6 2L 4 cyl engine.
When I started the car, lots of white smoke comes out of the exhaust.
Thinking it was an oil problem, I had new valve stem seals installed, plus a new head gasket etc, The 4 cylinders all have excellent equal pressure.
This did not solve the problem, as I now realize that the white smoke is actually water steam, and not oil.
The engine fuel mixture is running too rich, as the plugs are
very black.
Is it possible that the problem could be due to something wrong
with the inlet manifold? Could a broken manifold gasket cause these symptoms.
I do not have a car manual, but someone said that they think there is some sort of water pipe which is connected to the inlet manifold. (Which might account for the steam)
Can anyone please give me some advice on this problem.

Oct 28, 2009 | 1990 Ford Probe

2 Answers

1994 Ford Probe GT standard transmission - Will not shift into first or second while car is running. Shifts fine while car is off.


Check your slave cylinder Usually located below the brake master cylinder. If there' Fluid you probably need a clutch.

Sep 09, 2009 | 1994 Ford Probe

1 Answer

Overheating


Water pump. Coolant Level and ratio. Radiator Fan. Clogged Radiator. (Head gasket as final option)

Thats about the entire list.

Good Luck! If you need more help. Please re-post.

Thanks for using FixYa - a FixYa rating is appreciated!!

Feb 10, 2009 | 1994 Ford Probe

Not finding what you are looking for?
1994 Ford Probe Logo

1,709 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...