Question about 1984 Ford Thunderbird

1 Answer

SEAL ON THE REAR END WERE DRIVE SHAFT HOOKS UP.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

This is called the front youke seal, if it is leaking you will have to replace the seal and the crsuh bearing underneath the seal and change the oil. you can reuse the crush seal so you need a tork wrench to do this. If you want detailed help doing this let me know and I will walk you threw it.

Posted on Sep 29, 2009

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
chitownbob45
  • 316 Answers

SOURCE: want to change a leaky seal on a axle shaft on

take off the housing cover in the middle of the rear end and to each side there is a retainer clip for each side. Pull it out and that side comes out. I don't think you needed to remove the rear end to do this though.

Posted on Oct 03, 2009

ftw1952
  • 10319 Answers

SOURCE: loose collar on rear end were pinion hooks to

It is the pinion yoke flange to the driveshaft. NO you can not cut it off. A large nut in the middle of it has to be removed. The nut attaches to the pinion driven gearand if cut off a new gear will be needed

Posted on May 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace rear seal (drive shaft) on manual trans and started leaking badly


Drive shaft have only one seal and seal rear side on metal bush
1 jak up littil gear box because after shaft remov ing time oil no feldown
2 remove drive shaft rear bolt
3 mesher drive shaft seal touching area
4 mesher drive shaft Bush touching area this area damage want send machine Shoppe bush cover and drive shaft that time send seal also
Damege change that Bush also

Apr 25, 2016 | 1998 Isuzu Amigo

1 Answer

How to remove rear diff. cover on a 87 honda acty ?


you may have to break the adhesive seal around the flange . Rem,ember that you will also have to pull the drive shaft (axles) to the diff. To break the adhesive seal you may use a jack and lift a bit under the pinion flange while using something like a chisel to help break the seal

Jan 05, 2015 | Honda Cars & Trucks

1 Answer

2003 gmc sierra 2500 hd axial seal leaks


not enough detail for what end the leak is at. Front sounds strange for a pickup unless 4 wheel drive and then if the style is open shaft behind the brake rotor this would require dissemble of a few more things. If from the rear,which is the common repair, this is from a worn axle bearing on the axle shaft,which causes wear to the rear axle seal either located on the shaft before the bearing to the outside. Or the second option can be a axle seal located in the end of the axle housing. when you remove the axle shaft you would be looking at the end of the housing tube and see this seal. On older models ( My younger days ) they would also install one on the inner side of the housing next to the Gear Unit in the center of housing, ( also known as the PIG Unit ).need further info....

Jun 05, 2013 | Cars & Trucks

2 Answers

1993 Chevy w/t 1500 rear end is leaking by drive shaft


The rear end seal.first block the wheels,so truck does not roll away.remove drive shaft four bolts to do this.might have to a pry bar to seperate .then take a center punch and make a mark on the nut.then mark the yoke.with a mark.this is done,so when its put back together,you dont over tightn the crush spacer.then remove the yoke.have a pan under neath to catch any rear end oil.remove yoke,then remove seal.reinstall seal,and reverse the process.hope this helped brad

Sep 16, 2011 | 1993 Chevrolet C1500

1 Answer

Rear axle removal on a 2004 f150 fx4


First thing is to make sure you chock the front tires so the truck will not roll. Raise the rear end and set it on jack stands. Put the transmission in Neutral and make sure the parking brake is off. Remove the rear tires and disassemble the brakes on the side with the leaking seal. Place a drain pan under the rear differential and remove the cover. Remove the differential shaft lock bolt. You will need to turn the drive shaft by hand to access the bolt. It will be on the right side off the spider gear housing. Only use a 5/16 or 8mm 6 point box end wrench to remove the bolt. After you remove the bolt reach on the top of the spider gear housing and push the differential lock shaft down to remove it. Make sure the spider gears do not rotate after you remove the shaft. If they do you will need to realign everything to reinstall the lock shaft. Push the axle shaft in enough to remove the "C" clip from the tip of it. The axle will now slide out of the rear end. You can use the tip of the axle shaft to remove the axle seal. If you're changing the bearing as well you will need a slide hammer with axle bearing adapters to remove it. You can use a socket and hammer to install the new bearing and seal. Be careful not to damage the bearing and seal. I recommend packing grease in the back side of the seal. This helps prevent the spring on the seal lip from coming off. Assembly is the reverse. Clean off all the gear oil from the differential cover and the axle. You can use RTV as a gasket if the OEM gasket is damaged. Fill the rear end with new gear oil of the proper type. Refer to your owner's manual.

Jun 05, 2010 | 2004 Ford F150

1 Answer

Loose collar on rear end were pinion hooks to drive shaft after it fell off. it is large in diameter and is very thick and heavy stuck between rear end and pinion were the drive shaft hooks up in the rear....


It is the pinion yoke flange to the driveshaft. NO you can not cut it off. A large nut in the middle of it has to be removed. The nut attaches to the pinion driven gearand if cut off a new gear will be needed

May 29, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

Leaking fluid from rear end


hello, fluid leaking out of rear end is probably the pinion shaft seal, its were the drive shaft hooks to the rearend, you have to drop drive shaft, take yoke off rearend, or if it is,more further towards the back,were wheels are, then you need axle shaft seal, you have one on both sides on the rearend, behind the drums, where the back brakes are, also look and see if its coming from back of transmission, where drive shaft goes into the transmission, see if you can tell what color fluid is, if its red, its probably rear transmission seal, where drive shaft goes into the transmission.

Apr 08, 2010 | 2003 Kia Sedona

2 Answers

Where is the rear pinion seal


It's in the rear differential under the yolk where the propeller shaft(Drive Shaft) connects to it!
Have a Nice Day!! GMJ

Mar 11, 2010 | 1998 Mercury Mountaineer

1 Answer

How hard is it to replace the rear main seal in a '87 Samurai?


Is it a 4x4 if it is you would have to seperate the tranny from transfer case and drive shaft tp change out seal.If not just drop the drive shaft and replace seal.We are talking about the rear seal at the end of the tranny.

May 17, 2009 | 1987 Suzuki Samurai

1 Answer

Leak at rear diff (pinion seal?) 03 4X4 ford ranger


the part is called the pinion flange seal, pull the drive shaft, remove the large nut on the flange the drive shaft connects to and remove the flange, then pry out the old seal and lube the lip of the new seal with motor oil and press it into the opening. The 7.5 hour estimate is way wrong, about 1.5 hours labor and $4 for the part.

Apr 23, 2009 | 2002 Ford Ranger Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...