Question about Hyundai Motor 2002 Elantra

Open Question

Need rear axle nut torque setting 2002 Hyundai Elantra

Posted by on

  • Anonymous Mar 28, 2014

    axle nut torque specs

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What tools are needed to remove a 2002 Hyundai Elantra GT front passenger axle ?


36mm socket and long breaker bar, 12mm and 14mm wrenches and a ball joint separator fork.

Oct 12, 2014 | Hyundai Motor 2002 Elantra

1 Answer

Need to intall new front exterior drivers side door handle on a 2002 Hyundai Elantra GLS


remove the interior door trim and you will see small nuts holding the handle onto the outer door skin. Remove any rods /clips and undo the nuts and the handle will come out.

Mar 18, 2014 | Hyundai Motor 2002 Elantra

1 Answer

What are the torque settings of the j2 1.8GLS 1996 hyundai elantra


cylinder head bolt torque

10 mm bolts

step 1 22 ft lbs
step 2 additional 60 degrees
step 3 additional 60 degrees

12 mm bolts

step 1 26 ft lbs.
step 2 additional 60 degrees
step 3 additional 60 degrees

exhaust manifold nut 32-41 ft lbs.

intake manifold nut 11-15 ft lbs.

rocker cover 71-86 in. lbs.

Dec 14, 2010 | Hyundai Motor 1996 Elantra

1 Answer

I want to know the torque spec for a wheel bearing on an Hyundai accent 2002


front hub axle nut 162-192 ft lbs.

lug nut 66-81 ft lbs.

rear hub nut 148-192 ft lbs.

Dec 11, 2010 | 2002 Hyundai Accent

1 Answer

How to disassemble the rear end in a 2000 gmc yukon and how to remove axles


Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Loosen the lug nuts on the wheel and tire assemblies but do not remove the lug nuts
  3. Raise and support the vehicle
  4. Remove or disconnect the following:
    • Wheel and tire assemblies
    • Axle lubricant into a suitable container
    • Rear driveshaft
    • Parking brake cable
    • Brake calipers
    • Shock absorbers from the axle brackets
    • Vent hose from the rear axle vent fitting
    • Nuts and the washers from the U-bolts
    • U-bolts, spring plates and spacers from the axle assembly
  5. Lower the axle assembly from the vehicle
To Install:
  1. Place the rear axle assembly under the vehicle
  2. Align the rear axle assembly with the springs then connect the spacers, spring plates and the U-bolts to the rear axle
  3. Raise the rear axle assembly into position
  4. Install or connect the following:
    • Washers and nuts to the U-bolts; Torque to: 59 lb-ft. (80 Nm) then, Torque to: 89 lb-ft. (120 Nm)
    • Vent hose to the rear axle vent fitting
    • Shock absorbers to the rear axle
    • Brake calipers (See: Brake Caliper)
    • Parking brake cable (See: Parking Brake Cable)
    • Rear driveshaft (See: Rear Driveshaft)
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  5. Fill the rear axle with lubricant
  6. Bleed the brake system (See: Brake Bleeding)
  7. Install the wheel and tire assemblies
  8. Lower the vehicle to the ground
  9. Torque lug nuts as follows:
    • Single Wheel: Torque to: 140 lb-ft. (190 Nm)
    • Dual Wheel: Torque to: 175 lb-ft. (240 Nm)
  10. Road test the vehicle to check performance
prev.gif next.gif

Aug 03, 2010 | 2000 GMC Yukon XL

1 Answer

How to replace 2002 hyundai elantra hub and bearing


With the car on ground, break loose the drive-axle nut, and the wheel nuts , than jack up the car, support it properly, remove the wheel ,remove the axle-nut.
Remove the brake caliper assembly-- support it properly.
Remove the two bolts that hold the hub bracket to the Macpherson strut assemble, remove the lower arm ball joint and remove the steering tie- rod ball-joint attached to the hub bracket. That's it.Slide off the hub /with the bracket off the drive-shaft.
Follow steps backwards to assemble back.

Apr 09, 2010 | Hyundai Motor 2002 Elantra

1 Answer

Cv joint replacement procedure


You will need to replace the entire CV axle. Loosen the axle nut, loosen the lug nuts, lift the car, remove the wheel, remove the axle nut, undo the tie rod end to free the steering knuckle, tap the axle out of the hub, then pry the other end of the axle out of the transmission. When putting the new axle in place, take care not to damage the transmission seals or the hub seals.

Oct 14, 2009 | 2000 Hyundai Elantra

2 Answers

How to replace front wheel bearing on 2003 GMC ENVOY


Jack up vehicle and support with jack stands
Take off wheel
remove brake caliper
remove caliper bracket
remove rotor
remove axle retaining nut cotter pin
remove axle retaining nut
remove axle from output flange
pull axle out of vehicle
hub and bearing assembly held in by 4 bolts

installation is reverse of removal. You will need to find out the torque specs for the axle retaining nut.

Jan 14, 2009 | 2002 GMC Envoy

Not finding what you are looking for?
Hyundai Motor 2002 Elantra Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...