Question about 2001 Hyundai Santa Fe

Open Question

How do i program keyless remote..where is alarm system located?

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ghost4548
  • 776 Answers

SOURCE: Program factory remote keyless entry: 2003 Hyundai XG350

The procedures you list require the Hyundai Keyless Remote programming module, which you don't have. This module is proprietary - only Hyundai Dealerships have it. There is a 10 pin connector under the dash (next to the DLC - Data Link Connector) which is used to connect the Keyless Remote Programming Module. This module has two switch positions "Ready" and "SAVE". When the switch is place in the 'SAVE" position, that's when the keyless remotes are activated to send their 'codes' to the Electronic Time and Control System (ETACS). The module's switch is then set to "Ready" and the remote is tested to see if it works properly.

Posted on May 27, 2009

ghost4548
  • 776 Answers

SOURCE: Programming factory remote on 2003 Hyundai XG350

Again, the remotes can only be programmed by a Hyundai Technician (ETACS - Electronis Time and Alarm Control System).

Posted on May 27, 2009

ghost4548
  • 776 Answers

SOURCE: Program factory remote keyless entry 2003 Hyundai XG350

I've informed you of what you need to do. Take the veh into a Hyundai Service Center - let them program the remotes.

Posted on May 31, 2009

ghost4548
  • 776 Answers

SOURCE: program factory remote keyless entry for 2003 Hyundai XG350

This bulletin supersedes TSB# 02-90-001.
DESCRIPTION: The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03
or newer) and Data Link Connector (DLC) Cable. SERVICE INFORMATION: The keyless adapter cable can be used on the following vehicles:

  • 2001 - 2004 MY Elantra
  • 2001 - 2004 MY Santa Fe
  • 2002 - 2004 MY Sonata
  • 2001 - 2004 MY XG300/350 0390020a.gif
NOTE
  • The 2003 - 2004 MY Tiburon does not need the Keyless Adapter Cable to add keyless entry remotes to the factory security system. Instead, the Hi-Scan Pro connects to the vehicle using only the DLC cable. See page BE-60 in the 2004 MY Tiburon Shop Manual for the latest instructions.
  • The most current Keyless Adapter Cable Instructions are available in the following shop manuals:
SHOP MANUAL

PAGES

2004 MY Elantra
BE-73 - BE-74
2004 MY Santa Fe
BE-43 - BE-44
2004 MY Sonata
BE-40 - BE-41
2004 MY XG350
BE-46 - BE-47
KEYLESS ADAPTER CABLE INSTRUCTIONS:
  1. Connect the keyless adapter cable to the Hi-Scan Pro DLC cable. 0390020b.gif
  2. Plug the keyless adapter into the vehicle's 10-pin multi-purpose connector located behind the driver's side lower instrument panel (next to the DLC). NOTE Sample vehicle shown is the Santa Fe.
    0390020c.gif
  3. Turn the Hi-Scan Pro ON
    and press ENTER
    . NOTE "Release date 29. Sep. 2003" OR LATER
    must appear on this screen. To update your SOL card with the latest software go to www.hmaservice.com and refer to TSB 00-00-001.
    0390020d.gif
  4. Select option "HYUNDAI VEHICLE DIAGNOSIS"
    and press ENTER
    . 0390020e.gif
  5. Select vehicle model and press ENTER
    . 0390020f.gif
  6. Select option "TRANSMITTER CODE SAVING"
    and press ENTER
    . 0390020g.gif
  7. Ensure that the key has been removed from the ignition cylinder before proceeding. 0390020h.gif
  8. Follow the steps noted on the Hi-Scan Pro screen to program the remote(s). NOTE The factory security system can only be programmed to accept two remote transmitters and MUST be programmed for both remote transmitters at the same time.
    0390020i.gif
  9. Press ESC
    on the Hi-Scan Pro and verify that the remote(s) are functioning properly.
  10. Turn the Hi-Scan Pro OFF
    and disconnect the adapter cable from the multi-purpose connector.

Posted on May 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset keyless door entry that is in lock out mode


Viper Keyless Entry Systems

https://www.viper.com/car/keylessentry/
Viper is the industry leader in keyless entry systems. Add the convenience of keylessentry to virtually any vehicle - even vehicles without power door locks!

Alarms, Remote Car Starters, Keyless Entry & Locks - JC ...

www.jcwhitney.com > Audio, Video & Electronics
20 out of 32 products in Alarms, Remote Car Starters, Keyless Entry & Locks ..... ofKeyless Entry & Car Alarms allow you to lock and unlock power door locks.
How to program your keyless entry keypad - Ford Ownerhttps://owner.ford.com/.../locks.../how-to-program...Ford Motor CompanyDiscover how to lock and unlock your doors and how to program memory settings that will adjust seats & mirrors for each driver.SecuriCodeā„¢ Keyless Entry Keypad - Ford Ownerowner.ford.com/.../locks.../securicode-keyless-entr...Ford Motor CompanyLearn how to set a 5 digit SecuriCode on the Ford keyless entry keypad. ... Sign out. Register/Sign In Ā· Your Vehicle. Service & Maintenance. Service & .... vehicle's SecuriCode keypad to lock and unlock your doors without having to use a key. ... Thekeypad will go into an anti-scan mode if you enter the wrong code seven ...How Programming Your Keyless Entry Can Make ... - Ford Life

Jan 08, 2016 | Cars & Trucks

1 Answer

Can I program the car to recognixe the key fob.


1996 Roadmaster

  1. Locate the programming connector located in the LH trunk. Trim may have to be pulled back to access programming connector. ( Connector has black/white wires leading up to it and it is not connected to anything.)
  2. Jump programming connector terminals. Leave terminals jumped unitl step 6.
  3. System should now lock and unlock doors to indicate programming mode has been entered.
  4. Press any button on keyless remote once. System should now lock and unlock doors, indicating successful programming of keyless remote.
  5. Repeat step 4 for additional remote or other existing keyless remote. NOTE: A maximum of only two Keyless Remotes can be programmed.
  6. Remove programming connector jumper wire to exit programming mode.
  7. Test remote(s).

Oct 19, 2015 | 1996 Buick Roadmaster

1 Answer

HOW PROGRAM THE KEY LESS ENTRY FOR SONATA 2012


  1. Cars
  2. Car Maintenance
  3. General Car Maintenance
  4. How to Program Keyless Entry Remotes in a Hyundai Sonata
How to Program Keyless Entry Remotes in a Hyundai Sonata By Christian Killian, eHow Contributor
20Found This Helpful The keyless entry system in your Hyundai Sonata is part of the factory alarm system. If you have to replace a lost or damaged remote, reprogramming will be necessary. The remote is important because not only does it lock and unlock the doors, it also arms and disarms that factory alarm when you open or close your car doors. New remotes are available from any Hyundai dealer. While they will program it for you, you can do it yourself and save a programming fee.
How to Program Keyless Entry Remotes in a Hyundai Sonata(Kleophaus Livingston/Demand Media)

Other People Are Reading


Step 1: Locate the fuse panel under the dash on the driver's side of the car. Just below it is the control module for the factory alarm system. Open the cover on the alarm system control module and locate the memory switch inside.
(Kleophaus Livingston/Demand Media) Step 2: Verify that the switch is in the "Off" position; if it is not, switch it to the "Off" position. This is important for the system to understand what you want it to do when you move to the programming mode.
(Kleophaus Livingston/Demand Media) Sponsored Links
Step 3: Insert the key into the ignition of your Sonata and turn the key to the "On" position. Wait for 60 seconds, then move the memory switch inside the control module to "Set."
(Kleophaus Livingston/Demand Media) Step 4: Depress and hold the "Lock" button on your remote for one full minute. This allows the remote and the control module to communicate and sync. Release the "Lock" button and turn the memory switch in the control module back to the "Off" position.
(Kleophaus Livingston/Demand Media) Step 5: Turn the ignition switch to the "Off" position and test the remote by pressing the "Lock" or "Unlock" button, verifying that the doors do lock or unlock.


Read more : http://www.ehow.com/how_6362326_program-entry-remotes-hyundai-sonata.html

Mar 29, 2015 | Hyundai Sonata Cars & Trucks

1 Answer

I need instructions to program keyless entry remote for 2002 Hundai Santa Fe


For a 1994 to 2006 Sonata, a 2001 to 2006 Elantra, a 2000 to 2006 XG350 or a 2001 to 2006 Santa Fe, you will need to access alarm system control module. On most of those vehicles it is located on the driver's side fascia panel. But on the Sonata, the facia panel is in the center.

  • 2 Once you have found this module, you will want to ensure that the memory switch is in the OFF position. Then turn the ignition on.
  • 3 Wait 5 seconds and set the memory switch to SET position and then press the remote transmitter lock button to send the code to the alarm system control module.
  • 4 If you would like to program a second remote transmitter then you will need to press second remote transmitter lock button.
  • 5 Next set the memory switch to off, then turn the ignition off. You can confirm your programming by locking and unlocking the vehicle with both of the remotes. good luck my friend
  • Feb 08, 2012 | Hyundai Cars & Trucks

    1 Answer

    New batteries but remote won't click the door(s) or trunk. Ron


    try programming the remote again, here is how u do that. if this doesn't fix the problem the remote may be defective, if you need a new one try ebay, they are very cheap to buy there.

    .

    Note: Existing keyless remotes will be erased with this procedure.
    Existing working remotes will have to reprogrammed also.
    1. Locate the programming connector wire located in the RH trunk area.
    You may have to pull back right side trunk trim on trunk wall to locate
    the single black/white wire.

    2. The programming connector wire should have one termial in the plastic
    connector on end of black/white wire. Ground the terminal in the connector
    to a nearby bolt or trunk latch.
    Leave connector wire connected to ground through out procedure.
    3. System will now lock and unlock doors automatically to indicate
    programming mode has been activated.
    4. Press any button on keyless remote. System will respond by locking
    and unlocking doors one time to indicate successful programming.
    5. Repeat step 4 for to program any additonal keyless remotes including
    and existing keyless remotes. Do not remove ground wire between
    programming of keyless remotes.
    6. Disconnect programming connector wire from ground to exit programming
    mode.
    7. Test keyless remote(s).

    Nov 30, 2009 | 1994 Pontiac Grand Prix

    2 Answers

    Program factory remote keyless entry: 2003 Hyundai XG350


    The procedures you list require the Hyundai Keyless Remote programming module, which you don't have. This module is proprietary - only Hyundai Dealerships have it. There is a 10 pin connector under the dash (next to the DLC - Data Link Connector) which is used to connect the Keyless Remote Programming Module. This module has two switch positions "Ready" and "SAVE". When the switch is place in the 'SAVE" position, that's when the keyless remotes are activated to send their 'codes' to the Electronic Time and Control System (ETACS). The module's switch is then set to "Ready" and the remote is tested to see if it works properly.

    May 22, 2009 | Hyundai Motor 2003 XG350

    1 Answer

    Program factory remote keyless entry 2003 Hyundai XG350


    I've informed you of what you need to do. Take the veh into a Hyundai Service Center - let them program the remotes.

    May 22, 2009 | Hyundai Motor 2003 XG350

    1 Answer

    Program factory remote keyless entry for 2003 Hyundai XG350


    This bulletin supersedes TSB# 02-90-001.
    DESCRIPTION: The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03
    or newer) and Data Link Connector (DLC) Cable. SERVICE INFORMATION: The keyless adapter cable can be used on the following vehicles:
    • 2001 - 2004 MY Elantra
    • 2001 - 2004 MY Santa Fe
    • 2002 - 2004 MY Sonata
    • 2001 - 2004 MY XG300/350 0390020a.gif
    NOTE
    • The 2003 - 2004 MY Tiburon does not need the Keyless Adapter Cable to add keyless entry remotes to the factory security system. Instead, the Hi-Scan Pro connects to the vehicle using only the DLC cable. See page BE-60 in the 2004 MY Tiburon Shop Manual for the latest instructions.
    • The most current Keyless Adapter Cable Instructions are available in the following shop manuals:
    SHOP MANUAL

    PAGES

    2004 MY Elantra
    BE-73 - BE-74
    2004 MY Santa Fe
    BE-43 - BE-44
    2004 MY Sonata
    BE-40 - BE-41
    2004 MY XG350
    BE-46 - BE-47
    KEYLESS ADAPTER CABLE INSTRUCTIONS:
    1. Connect the keyless adapter cable to the Hi-Scan Pro DLC cable. 0390020b.gif
    2. Plug the keyless adapter into the vehicle's 10-pin multi-purpose connector located behind the driver's side lower instrument panel (next to the DLC). NOTE Sample vehicle shown is the Santa Fe.
      0390020c.gif
    3. Turn the Hi-Scan Pro ON
      and press ENTER
      . NOTE "Release date 29. Sep. 2003" OR LATER
      must appear on this screen. To update your SOL card with the latest software go to www.hmaservice.com and refer to TSB 00-00-001.
      0390020d.gif
    4. Select option "HYUNDAI VEHICLE DIAGNOSIS"
      and press ENTER
      . 0390020e.gif
    5. Select vehicle model and press ENTER
      . 0390020f.gif
    6. Select option "TRANSMITTER CODE SAVING"
      and press ENTER
      . 0390020g.gif
    7. Ensure that the key has been removed from the ignition cylinder before proceeding. 0390020h.gif
    8. Follow the steps noted on the Hi-Scan Pro screen to program the remote(s). NOTE The factory security system can only be programmed to accept two remote transmitters and MUST be programmed for both remote transmitters at the same time.
      0390020i.gif
    9. Press ESC
      on the Hi-Scan Pro and verify that the remote(s) are functioning properly.
    10. Turn the Hi-Scan Pro OFF
      and disconnect the adapter cable from the multi-purpose connector.

    May 22, 2009 | Hyundai Motor 2003 XG350

    1 Answer

    Alarm problem on my 2001 elantra


    This alarm system can only be 'disarmed' using the keyless remote programmed for this specific vehicle. Press the "Unlock" button on the keyless remote -- this resets/disarms the alarm system. If you do not have keyless remote for this vehicle, get one and have it programmed at a Hyundai Service Center. Problem solved.

    May 11, 2009 | 2001 Hyundai Elantra

    1 Answer

    VEHICLE WONT START


    Section 13-11: Anti-Theft System, Active 1998 Windstar Workshop Manual DESCRIPTION AND OPERATION Anti-Theft Alarm System NOTE: The system immediately monitors the ignition key lock cylinder upon removal of the key from the ignition. It is not necessary to arm the system for ignition key lock monitoring.

    The anti-theft alarm system:
    • protects the vehicle from unauthorized entry into the passenger compartment, engine compartment and cargo area.
    • monitors the status of the ignition key lock cylinder.
    • is controlled by a remote anti-theft personality (RAP) module. The remote anti-theft personality module also controls the electronic door lock functions. Refer to Section 01-14B for more details.
    • when armed, detects unauthorized entry into the passenger compartment by using an input from the GEM module regarding the state of the door or liftgate (open or closed).
    • protects the engine compartment with a hood switch which is located on the LH cowl vent panel and is part of windshield wiper motor wiring (17A477) .
    • triggers an alarm if the ignition lock cylinder is forcibly removed from the steering column.
    Once triggered, the system responds by:
    • flashing the low beam headlamps, the parklamps, rear lamps and the alarm indicator warning light emitting diode (LED).
    • sounding the horn (13832).
    • disabling the starter circuit until the system is disarmed.
    ---------------------------------------------------------------------------------------------
    Remote Anti-Theft Personality Module
    • The remote anti-theft personality module is located behind the instrument panel (04320).
    • It contains a radio receiver that receives the RF signal from the keyless entry remote transmitter (15K601) through the alarm and lock system antenna (15603) and sends the appropriate command to the power door locks, the horn relay, or the generic electronic module.
    • The remote anti-theft personality module is equipped with an internal backup power supply which holds the programmed code in memory in the event the vehicle battery is disconnected.
    -------------------------------------------------------------------------------
    Remote Anti-Theft Personality Module Removal
    1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    1. Remove radio. Refer to Section 15-01 .
    1. Remove lower instrument panel center finish panel. Refer to Section 01-12 .
    1. Lower glove box.
    1. Remove two remote anti-theft personality module bracket retaining screws.
    1. Disconnect electrical connectors and alarm and lock system antenna (15603).
    1. Remove remote anti-theft personality module and bracket.
    1. Remove remote anti-theft personality module from mounting bracket.
    Installation
    1. To install, follow removal procedure in reverse order.
    1. Tighten remote anti-theft personality module bracket retaining screws to 6-8 Nm (54-70 lb-in).

      34bdf35.gif
    Components The system is composed of the following components:
    • remote anti-theft personality (RAP) module with integral antenna
    • alarm indicator LED
    • door lock cylinder switch RH, door lock cylinder switch LH
    • liftgate door lock cylinder switch (220A40)
    • hood switch (part of windshield wiper motor wiring (17A477))
    • ignition lock anti-theft switch (19A438)
    The following vehicle components are also used by the anti-theft alarm system:
    • generic electronic module
    • power door lock switch (14028)
    • door open warning lamp switch (14018)
    • autolamp relay (14N089)
    • horn relay and bracket (13853) and horn (13832)
    • low beam headlamps
    • rear lamps (13404) and parking lamps (13200)
    • starter relay
    • door lock relays
    • keyless entry remote transmitter (15K601)
    --------------------------------
    Disarming an Untriggered System NOTE: A perimeter alarm will "shut off" after 165 seconds, but the system is still triggered and is not disarmed.

    An armed but untriggered perimeter anti-theft system can be disarmed by one of the following four events:
    1. Unlock the doors by pressing the keyless entry remote transmitter (15K601) UNLOCK button once.
    2. Unlock any door with a key.
    3. Turn ignition switch to RUN or ACC.
    4. The remote entry PANIC button will disarm the anti-theft system only when the perimeter alarm is triggered and sounding.
    ------------------------------------------------
    System Triggering NOTE: Although the remote entry PANIC alarm is not associated with the monitoring of the vehicle, the user will frequently say that the theft system was triggered when actually the keyless entry remote transmitter PANIC button was inadvertently pressed. A panic alarm will not flash the THEFT indicator.

    The alarm can be triggered by the following events if the system has been armed and has not been disarmed first:
    • Open any door or liftgate.
    • Open the hood (16612) (if the hood was open when the system was armed, it must be closed before it can trigger the alarm).
    • Dislodge the ignition key lock cylinder.
    • The anti-theft system may be triggered inadvertently when the module is disconnected and then reconnected. To avoid inadvertent alarm triggering, disconnect the smaller 22-way connector first.
    When the system is triggered the perimeter alarm will operate as follows: The remote anti-theft personality module will pulse the following outputs at approximately 1.3 Hz, 50 percent duty cycle for two minutes 45 seconds for North America. NOTE: Other perimeter alarms can be programmed for the system.

    • low beam headlamps
    • parking lamps
    • horn
    • THEFT indicator
    The perimeter alarm can be retriggered, after a perimeter alarm has sounded for 165 seconds. After a perimeter alarm has timed out, if any trigger input is first seen as normal and is then seen in its trigger state, the perimeter alarm will be retriggered. The perimeter alarm can be triggered a total of three times between an arming sequence and a disarm event. An active panic alarm will be deactivated when a perimeter alarm is triggered (a perimeter alarm overrides a panic alarm).

    Mar 02, 2009 | 1998 Ford Windstar

    Not finding what you are looking for?
    2001 Hyundai Santa Fe Logo

    Related Topics:

    95 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    75817 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8180 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...